Search the Community

I have been running the payload to install the tools for the bashbunny but it is not working. It doesn't turn on the led at first and then it flashes a white light and it boots normally. After it boots there is no tools folder and the install.sh file doesn't change to INSTALLED. Is there anyway I can fix this or is there another way to install the tools?

My Wifi Pineapple Nano Tactical Elite edtion just arrived and I have some problems with it. The Wifi dongle wich it came with disconnect's after around 5 minutes, my system logs gives the following: Tue Jun 6 15:53:31 2017 kern.info kernel: [ 394.880000] wlan2: authenticate with e4:f4:c6:XX:XX:XX Tue Jun 6 15:53:31 2017 kern.info kernel: [ 394.940000] wlan2: send auth to e4:f4:c6:XX:XX:XX (try 1/3) Tue Jun 6 15:53:31 2017 kern.info kernel: [ 394.950000] wlan2: authenticated Tue Jun 6 15:53:31 2017 kern.info kernel: [ 394.960000] wlan2: associate with e4:f4:c6:XX:XX:XX (try 1/3) Tue Jun 6 15:53:31 2017 kern.info kernel: [ 394.960000] wlan2: RX AssocResp from e4:f4:c6:XX:XX:XX (capab=0x1411 status=0 aid=2) Tue Jun 6 15:53:31 2017 kern.info kernel: [ 395.000000] wlan2: associated Tue Jun 6 15:53:32 2017 daemon.notice netifd: Network device 'wlan2' link is up Tue Jun 6 15:53:32 2017 daemon.notice netifd: Interface 'wan' has link connectivity Tue Jun 6 15:53:32 2017 daemon.notice netifd: Interface 'wan' is setting up now Tue Jun 6 15:53:32 2017 kern.info kernel: [ 395.120000] wlan2: deauthenticating from e4:f4:c6:XX:XX:XX by local choice (Reason: 3=DEAUTH_LEAVING) Tue Jun 6 15:53:32 2017 daemon.notice netifd: Network device 'wlan2' link is down Tue Jun 6 15:53:32 2017 daemon.notice netifd: Interface 'wan' has link connectivity loss And when the dongle is working then for some reason my SD-Card is not showing up, I am using a Sandisk 16GB Micro SD Ultra. Greetings, Nathan102

Hello, I just received my WifiPineapple Elite edition in the mail today and i am having issues setting it up. I run my Kali 2.0 through virtualbox and it is setup with a bridged connection. I've added the WP to the list of USB devices in the VM settings. I run the wp6 and do the guided setup, confirm my default address as 10.0.2.1, confirm eth0 is my internet connection, then confirm that eth1 is the pineapple. I look at my network connection and it shows both eth0 and eth1 are connected. My ip to eth0 is given as 10.0.2.100 and eth1 is 172.16.42.42. When i select "connect using saved settings" in the wp6 script, it says it is "detecting wifi pineapple" and just hangs there, throwing periods for dayzzz! I cant ping 172.16.42.1 either. Anybody know whats going on? Thank you.

I mean Not getting stuck while scanning wifi networks. With clients not losing connectivity all the time SD Card reads all the time Broadcast SSID Pool all the time not just a few minutes Or it's just me?? I already reset, format, reboot many times, checked all the instructions, I'm pretty sure is not an user problem I wished i read the post from this forum before i bought the nano elite, it seems like many users have the same problem, so far is just an expensive brick.

Good Morning all, I have upgraded to the new Codename Buffalo Bulldozer release and have been running into some issues using PineAP. With the settings as Allow Associations, Log Probes, Log Associations, PineAP Daemon: Enabled, Capture SSIDs to Pool, Beacon Response and Beacon Response Interval set to Aggressive I have not been able to get clients to connect as before with the previous release, before these settings would work flawlessly and any device not connected to wifi but beaconing would be added to the SSID Pool and connected as a client. Now I am unable to get any automatic associations, matter of fact for the last two days I have been working with the new firmware I have yet to get any ( I have three devices set up probing right next to the Pineapple). It doesn't even seem to be reading the Probes but sporadically and even then its two at max. Just wondering if anyone else is having these issues? Also the Save active config as default dose not seem to be working as before, with the same settings annotated above every time I start up the NANO PineAP is Disabled... The previous version fired right up into the settings I needed. Thanks in advance for the support Oh and not to pile too much into one post but I have had the Recon hang at 100% again, I hope these issues are user error lol since the release directly addressed this issue.

Good evening, I own a wifi pineapple nano and ever since the firmware upgrade it has been acting funny I wiped it 3 days ago and it was working fine yesterday. Today it won't even stay on at all I plug it up and lights up then turns right back off. Also after not even having it for 3 months the antennae broke on it the black part came off and after continuous attmpts to make it stay on the wite finally ended up breaking. Please help I would like to be assured that the $200 I spent wasn't a waste of money......

So I recently bought a Pineapple Mark V, and for some reason when I went to plug it in earlier it wouldn't turn on. I've went through all the logical checks, there have been no power surges, I've never cut it on without having antennas plugged in, it stays in the box it came in on a shelf when not in use, no one else has used it, I have not messed with any of the DO NOT TOUCH UNLESS YOU KNOW WHAT YOUR DOING stuff. I don't know what to do. I tried factory reseting it to get it to cut on by putting the second and third switches in the down position, cutting it on and leaving it on for five minutes with no response. No LEDs light up it wont conenect via ethernet nothing. Please help. It is still within warantee and if I cannot get it to work then I will just have it replaced as this is obviously a manufacturer issue, but I was hoping SOMEONE might know how to fix this.

Hello hak5! My name is Danny and im 20 years old. I come from Denmark and at this point I'm writing my final project. My subject is "DDoS" - "How can the British authorities tackle DDoS-attacks" Therefor I have to explain how a DDoS attack actually works. Also I have to involve technical, legal and ethical issues that may arise in connection with DDoS-attacks. I hope you can help me with some of these questions. Appreciated. Regards from Kappa!

Hi, I just received my WiFi Pineapple Mark V today. I successfully updated the firmware. I was about to plug the ethernet cable into the Mark V and then I started hearing clicking noises coming from the power adapter, and when I looked at the Mark V there is no lights on the Mark V and unplugging/replugging in the power adapter into the Mark V did nothing. Then the power adapter stopped making the noises and power came back to the Mark V, and after a few minutes it starts happening again? Sounds strange; Anyone else had similar issues? Should I stop using the power adapter incase it fries my Mark V? Any UK Mark V owners replaced the bundle power adapter with a UK only power adapter? The included battery pack, doesn't have a UK plug, can I use the bundle UK plug from the mains adapter? I guess I am lucky it didn't happen while I was updating the firmware :) Regards,

OK.. I have been on this for about 12 hours now trying to setup my Pineapple. I..Think..I..Need..help.. I'm breaking down my setup/connection so you all get the gist. Computer Hardware: 15" Retinal MBP Pineapple hardware Version: MarkV Pineapple Firmware Version: 1.0.4 OS used to connect to the Pineapple: OS X Mavericks Network Layout: Pineapple is supplied power from wall outlet. I have my wifi pineapple connected to my Mac via USB to ethernet, ethernet cable connected into pineapple. My Mac is connected via WiFi from my personal Access Point. I have manually configured the settings per the booklet that came with the Pineapple.-- IP address: 172.16.42.42 / subnet mask 255.255.255.0 / DNS server: 8.8.8.8 (I have toggled this on and off) . I have set the connection service order Wi-Fi FIRST and then USB ethernet SECOND. REMINDER: (no I'm not forgetting the part where I turn on ICS in the sharing tab inside system preferences.. I'll get to that part in just a moment) After the hardware is set up you go to sign in and essentially when setting up the pineapple you have to create a password, accept the terms and then you're in. Walla, right?! not so much. Here's what happened... After the "first boot setup" I Looked at the pineapple hardware and noticed I got a solid green. "POWERED" and secondly I get Yellow "ETHERNET". I got in and played around checking out the WiFi Pineapple - Management interface. Went to set up Karma it was as easy as typing in your personal access point name and then clicking START from the main menu. The newly named AP would show up in the "looking for WiFi networks" menu. AWESOME. Went to connect to the device with another computer to start this party and no connection. Bummer. Then I noticed that I had not turned on ICS. Turned that on in system preferences / sharing tab and toggled USB Ethernet check box then checked internet sharing and POW we should have connection right? nope. This is where it all went down hill. After I did this I tried to connect back to the http://172.16.42.1:1471 site and it would not. Turned off ICS and rebooted my computer and I get connection. weird. I thought something went wrong so I reset the Pineapple to system defaults. Went through everything again and same issue occurred. Went to try and run updates and no connection. This is with ICS turned OFF. Here's where things get weird.. After the 3rd or 4th default reset (using the dip switches, AWESOME) I noticed a solid blue light on the pineapple "ARN331"... Not sure what caused that but I got something different. Went to run updates and randomly I could! (at this point the pineapple could connect to run updates and install infusions but not give off any wifi to have other clients connect) I ran all my updates and even did the firmware update 1.0.4 and I thought surly I was good to go. At this point I downloaded infusions and getting everything set up. Went to have some fun and tried to connect a computer to Karma's "made up AP" that I created and stillllll no connection. Frustrated I reset back to defaults and tried everything over again. Firmware is still at 1.0.4 (latest update as of 11/23/2013) This time I get ALL LIGHTS on my pineapple! green yellow blue and red! (this is still with no ICS on.. because IF I do that I can't even connect to http://172.16.42.1:1471 it just times out on my web browser) Went to connect a device to my Karam "made up AP" and walla I had it made. Don't know what I did different but I had connection. Just to make sure it was not a fluke. I unplugged the Pineapple and connected it back up and now I only get green yellow blue lights. ------------------------- My setup: I have not changed a thing. Everything is still the same, yet I got different results after a power cycle. I tried a different ethernet cable but they both responded the same. Rebooted my computer multiple times to make sure connection was clear. ERRORS I get right now: When I go to Pineapple bar I get "Error connecting. Please check your internet connection!" (but remember I got into here to run updates before.. with the same exact settings before) I also get the error under Network tab Internet IP: "error connecting"... although randomly when I could connect to the pineapple bar/ run updates but NOT have karma working I got a internet IP (obviously) My Question is: What should my settings be? I had full connection but lost it. I have read and re read all the OS X Setup forums. The youtube videos. None of them work.. suggestions? I'm willing to do anything, to start all over, to order a new one whatever at this point.. I just want this thing to work.. what should my settings be?

Hello, Has anybody experienced issues with the hak5 shop lately ? I tried using two different credit cards to make a purchase but it gives me "Error from gateway, Your card was decline" The funny thing is it doesn't even show up with the bank that the payment attempt was ever made. I tried contacting support but they couldnt help me much. It seems like its an issue with the hak5 payment gateway. :(