Search the Community

What's up everybody, I'm having some issues. I just got a new wifi pineapple nano tactical and it's not being detected by Kali. It powers on, flickers a little before becoming solid blue. I followed the tutorial exactly as show and still no results. I issued a iwconfig, dmesg, lsusb and nothing is listed. Just to eliminate all possibilities, I used another wireless usb and it registered ASAP. Just wondering if the device may be defective or if there's something that I'm not accounting for. Please help! I'm teaching myself about pen testing and cyber security in general, even installed Snort on my ubuntu machine and have been fun with that. Any help would be greatly appreciated!

I love this little thing, I've had it for less than a week and I've learned a lot already. Sadly, my WLAN0 has gone missing from my WIFI Client dropdown menu under Networking. I can see that it exsists under the Advanced Menu, I can also change it's MAC address. I was using an AWUS036H, a tiny Edimax Dongle and/or the tiny dongle sold by Hakshop testing out range for about an hour. I turned it off via the GUI, came back to it a few hours later and I was wlan0-less. I wish I knew more about the UNIX commands but I don't at the moment. Somewhere in one of the logs, I believe I saw something that seemed the firmware for one of the dongles had replaced the wlan0 firmware. I'm not sure but I sure do miss it. I get paranoid when powerful little tools act funky. Could you glance over these logs and tell me if something nefarious is going on? I've reset it hard and soft, flashed the firmware and updated it all in different order several times. The logs change slightly from here to there but I can't tell what it all means exactly. Here are the logs from this morning (5am is) DMESG AFTER REFLASHING FIRMWARE: [ 0.000000] Linux version 3.18.23 (sebkinne@Worker) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46591) ) #13 Thu Jan 21 13:34:28 PST 2016 [ 0.000000] MyLoader: sysp=8a14b024, boardp=44b65156, parts=b69f8d32 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80355cf0, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=PINEAPPLE-NANO console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 60944K/65536K available (2465K kernel code, 128K rwdata, 528K rodata, 260K init, 188K bss, 4592K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] NET: Registered protocol family 16 [ 0.100000] MIPS: machine is WiFi Pineapple NANO [ 0.380000] Switched to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.400000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.400000] TCP: reno registered [ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] NET: Registered protocol family 1 [ 0.420000] PCI: CLS 0 bytes, default 32 [ 0.420000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.450000] msgmni has been set to 119 [ 0.460000] io scheduler noop registered [ 0.460000] io scheduler deadline registered (default) [ 0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART [ 0.480000] console [ttyATH0] enabled [ 0.490000] bootconsole [early0] disabled [ 0.500000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.500000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.510000] 5 tp-link partitions found on MTD device spi0.0 [ 0.510000] Creating 5 MTD partitions on "spi0.0": [ 0.520000] 0x000000000000-0x000000020000 : "u-boot" [ 0.520000] 0x000000020000-0x000000134994 : "kernel" [ 0.530000] 0x000000134994-0x000000ff0000 : "rootfs" [ 0.530000] mtd: device 2 (rootfs) set to be root filesystem [ 0.540000] 1 squashfs-split partitions found on MTD device rootfs [ 0.540000] 0x000000db0000-0x000000ff0000 : "rootfs_data" [ 0.550000] 0x000000ff0000-0x000001000000 : "art" [ 0.560000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.590000] libphy: ag71xx_mdio: probed [ 1.190000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.200000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 1.200000] TCP: cubic registered [ 1.200000] NET: Registered protocol family 17 [ 1.210000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.220000] 8021q: 802.1Q VLAN Support v1.8 [ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.240000] Freeing unused kernel memory: 260K (8036f000 - 803b0000) [ 2.640000] init: Console is alive [ 2.640000] init: - watchdog - [ 5.280000] usbcore: registered new interface driver usbfs [ 5.290000] usbcore: registered new interface driver hub [ 5.290000] usbcore: registered new device driver usb [ 5.350000] SCSI subsystem initialized [ 5.360000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.370000] ehci-platform: EHCI generic platform driver [ 5.370000] ehci-platform ehci-platform: EHCI Host Controller [ 5.380000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.390000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 5.410000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 5.410000] hub 1-0:1.0: USB hub found [ 5.410000] hub 1-0:1.0: 1 port detected [ 5.420000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.430000] ohci-platform: OHCI generic platform driver [ 5.440000] uhci_hcd: USB Universal Host Controller Interface driver [ 5.450000] usbcore: registered new interface driver usb-storage [ 5.740000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 5.780000] init: - preinit - [ 6.070000] hub 1-1:1.0: USB hub found [ 6.070000] hub 1-1:1.0: 4 ports detected [ 6.440000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 6.670000] random: procd urandom read with 11 bits of entropy available [ 6.810000] mount_root: loading kmods from internal overlay [ 7.070000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform [ 7.110000] block: attempting to load /etc/config/fstab [ 7.230000] block: extroot: not configured [ 7.230000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 7.280000] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 7.280000] scsi host0: usb-storage 1-1.2:1.0 [ 7.310000] procd: - early - [ 7.310000] procd: - watchdog - [ 8.230000] procd: - ubus - [ 8.430000] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0933 PQ: 0 ANSI: 6 [ 8.540000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 9.260000] procd: - init - [ 13.420000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 13.430000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 13.470000] cfg80211: Calling CRDA to update world regulatory domain [ 13.490000] cfg80211: World regulatory domain updated: [ 13.490000] cfg80211: DFS Master region: unset [ 13.490000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 13.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 13.510000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 13.520000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 13.530000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 13.540000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 13.550000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 13.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 13.560000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 13.700000] ath: EEPROM regdomain: 0x0 [ 13.700000] ath: EEPROM indicates default country code should be used [ 13.700000] ath: doing EEPROM country->regdmn map search [ 13.700000] ath: country maps to regdmn code: 0x3a [ 13.700000] ath: Country alpha2 being used: US [ 13.700000] ath: Regpair used: 0x3a [ 13.710000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 13.710000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 13.730000] usb 1-1.1: ath9k_htc: Firmware htc_9271.fw requested [ 13.740000] usbcore: registered new interface driver ath9k_htc [ 13.790000] cfg80211: Calling CRDA for country: US [ 13.810000] cfg80211: Regulatory domain changed to country: US [ 13.810000] cfg80211: DFS Master region: FCC [ 13.810000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 13.820000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 13.830000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A) [ 13.840000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) [ 13.850000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s) [ 13.860000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 13.870000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 13.880000] RPC: Registered named UNIX socket transport module. [ 13.880000] RPC: Registered udp transport module. [ 13.890000] RPC: Registered tcp transport module. [ 13.890000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 13.930000] tun: Universal TUN/TAP device driver, 1.6 [ 13.930000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 13.990000] usbcore: registered new interface driver rt2800usb [ 14.000000] usbcore: registered new interface driver rtl8187 [ 14.050000] usbcore: registered new interface driver rtl8192cu [ 14.080000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 14.100000] usbcore: registered new interface driver cdc_acm [ 14.100000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 14.140000] usbcore: registered new interface driver cdc_wdm [ 14.170000] nf_conntrack version 0.5.0 (956 buckets, 3824 max) [ 14.190000] usb 1-1.1: ath9k_htc: Transferred FW: htc_9271.fw, size: 50980 [ 14.240000] usbcore: registered new interface driver ums-alauda [ 14.250000] usbcore: registered new interface driver ums-cypress [ 14.260000] usbcore: registered new interface driver ums-datafab [ 14.260000] usbcore: registered new interface driver ums-freecom [ 14.270000] usbcore: registered new interface driver ums-isd200 [ 14.290000] usbcore: registered new interface driver ums-jumpshot [ 14.310000] usbcore: registered new interface driver ums-karma [ 14.320000] usbcore: registered new interface driver ums-sddr09 [ 14.320000] usbcore: registered new interface driver ums-sddr55 [ 14.330000] usbcore: registered new interface driver ums-usbat [ 14.360000] usbcore: registered new interface driver usbserial [ 14.370000] usbcore: registered new interface driver usbserial_generic [ 14.370000] usbserial: USB Serial support registered for generic [ 14.440000] xt_time: kernel timezone is -0000 [ 14.450000] usbcore: registered new interface driver asix [ 14.450000] usbcore: registered new interface driver cdc_ether [ 14.480000] ath9k_htc 1-1.1:1.0: ath9k_htc: HTC initialized with 33 credits [ 14.480000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.530000] usbcore: registered new interface driver pl2303 [ 14.530000] usbserial: USB Serial support registered for pl2303 [ 14.540000] PPP generic driver version 2.4.2 [ 14.550000] NET: Registered protocol family 24 [ 14.560000] usbcore: registered new interface driver qmi_wwan [ 14.570000] usbcore: registered new interface driver rndis_host [ 14.580000] usbcore: registered new interface driver sierra_net [ 14.600000] usbcore: registered new interface driver option [ 14.600000] usbserial: USB Serial support registered for GSM modem (1-port) [ 17.090000] ath9k_htc 1-1.1:1.0: ath9k_htc: FW Version: 1.3 [ 17.090000] ath9k_htc 1-1.1:1.0: FW RMW support: Off [ 17.100000] ath: EEPROM regdomain: 0x0 [ 17.100000] ath: EEPROM indicates default country code should be used [ 17.100000] ath: doing EEPROM country->regdmn map search [ 17.100000] ath: country maps to regdmn code: 0x3a [ 17.100000] ath: Country alpha2 being used: US [ 17.100000] ath: Regpair used: 0x3a [ 17.120000] ieee80211 phy1: Atheros AR9271 Rev:1 [ 25.070000] device eth0 entered promiscuous mode [ 28.170000] eth0: link up (100Mbps/Full duplex) [ 28.320000] br-lan: port 1(eth0) entered forwarding state [ 28.320000] br-lan: port 1(eth0) entered forwarding state [ 30.080000] device wlan0 entered promiscuous mode [ 30.090000] br-lan: port 2(wlan0) entered forwarding state [ 30.090000] br-lan: port 2(wlan0) entered forwarding state [ 30.320000] br-lan: port 1(eth0) entered forwarding state [ 30.560000] eth0: link down [ 31.560000] br-lan: port 1(eth0) entered disabled state [ 32.090000] br-lan: port 2(wlan0) entered forwarding state [ 32.560000] eth0: link up (100Mbps/Full duplex) [ 32.560000] br-lan: port 1(eth0) entered forwarding state [ 32.570000] br-lan: port 1(eth0) entered forwarding state [ 34.570000] br-lan: port 1(eth0) entered forwarding state [ 48.420000] random: nonblocking pool is initialized [ 63.590000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 63.590000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 63.600000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 73.340000] jffs2: notice: (1694) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 74.950000] device wlan0 left promiscuous mode [ 74.960000] br-lan: port 2(wlan0) entered disabled state [ 77.130000] device wlan0 entered promiscuous mode [ 77.130000] br-lan: port 2(wlan0) entered forwarding state [ 77.140000] br-lan: port 2(wlan0) entered forwarding state [ 78.710000] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 78.720000] scsi host1: usb-storage 1-1.2:1.0 [ 79.140000] br-lan: port 2(wlan0) entered forwarding state [ 79.720000] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 0933 PQ: 0 ANSI: 6 [ 79.720000] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 79.770000] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 86.470000] br-lan: port 2(wlan0) entered disabled state [ 86.730000] device wlan0 left promiscuous mode [ 86.740000] br-lan: port 2(wlan0) entered disabled state [ 86.780000] eth0: link down [ 87.470000] br-lan: port 1(eth0) entered disabled state [ 88.780000] eth0: link up (100Mbps/Full duplex) [ 88.780000] br-lan: port 1(eth0) entered forwarding state [ 88.790000] br-lan: port 1(eth0) entered forwarding state [ 90.790000] br-lan: port 1(eth0) entered forwarding state [ 232.940000] device wlan0 entered promiscuous mode [ 232.940000] br-lan: port 2(wlan0) entered forwarding state [ 232.950000] br-lan: port 2(wlan0) entered forwarding state [ 233.040000] device wlan0-1 entered promiscuous mode [ 233.050000] br-lan: port 3(wlan0-1) entered forwarding state [ 233.050000] br-lan: port 3(wlan0-1) entered forwarding state [ 233.570000] br-lan: port 3(wlan0-1) entered disabled state [ 233.770000] br-lan: port 3(wlan0-1) entered forwarding state [ 233.770000] br-lan: port 3(wlan0-1) entered forwarding state [ 234.950000] br-lan: port 2(wlan0) entered forwarding state [ 235.770000] br-lan: port 3(wlan0-1) entered forwarding state SYSTEM LOG AT SAME TIME AFTER FM FLASHING: Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.450000] usbcore: registered new interface driver cdc_ether Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.480000] ath9k_htc 1-1.1:1.0: ath9k_htc: HTC initialized with 33 credits Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.480000] ip_tables: (C) 2000-2006 Netfilter Core Team Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.530000] usbcore: registered new interface driver pl2303 Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.530000] usbserial: USB Serial support registered for pl2303 Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.540000] PPP generic driver version 2.4.2 Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.550000] NET: Registered protocol family 24 Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.560000] usbcore: registered new interface driver qmi_wwan Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.570000] usbcore: registered new interface driver rndis_host Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.580000] usbcore: registered new interface driver sierra_net Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.600000] usbcore: registered new interface driver option Thu Jan 21 21:34:28 2016 kern.info kernel: [ 14.600000] usbserial: USB Serial support registered for GSM modem (1-port) Thu Jan 21 21:34:28 2016 kern.info kernel: [ 17.090000] ath9k_htc 1-1.1:1.0: ath9k_htc: FW Version: 1.3 Thu Jan 21 21:34:28 2016 kern.info kernel: [ 17.090000] ath9k_htc 1-1.1:1.0: FW RMW support: Off Thu Jan 21 21:34:28 2016 kern.debug kernel: [ 17.100000] ath: EEPROM regdomain: 0x0 Thu Jan 21 21:34:28 2016 kern.debug kernel: [ 17.100000] ath: EEPROM indicates default country code should be used Thu Jan 21 21:34:28 2016 kern.debug kernel: [ 17.100000] ath: doing EEPROM country->regdmn map search Thu Jan 21 21:34:28 2016 kern.debug kernel: [ 17.100000] ath: country maps to regdmn code: 0x3a Thu Jan 21 21:34:28 2016 kern.debug kernel: [ 17.100000] ath: Country alpha2 being used: US Thu Jan 21 21:34:28 2016 kern.debug kernel: [ 17.100000] ath: Regpair used: 0x3a Thu Jan 21 21:34:28 2016 kern.info kernel: [ 17.120000] ieee80211 phy1: Atheros AR9271 Rev:1 Thu Jan 21 21:34:30 2016 user.emerg syslog: this file has been obseleted. please call "/sbin/block mount" directly Thu Jan 21 21:34:31 2016 cron.info crond[1328]: crond (busybox 1.23.2) started, log level 5 Thu Jan 21 21:34:34 2016 daemon.notice netifd: Interface 'lan' is enabled Thu Jan 21 21:34:34 2016 daemon.notice netifd: Interface 'lan' is setting up now Thu Jan 21 21:34:34 2016 kern.info kernel: [ 25.070000] device eth0 entered promiscuous mode Thu Jan 21 21:34:35 2016 daemon.notice netifd: Interface 'lan' is now up Thu Jan 21 21:34:35 2016 daemon.notice netifd: Interface 'loopback' is enabled Thu Jan 21 21:34:35 2016 daemon.notice netifd: Interface 'loopback' is setting up now Thu Jan 21 21:34:35 2016 daemon.notice netifd: Interface 'loopback' is now up Thu Jan 21 21:34:35 2016 daemon.notice netifd: Network device 'lo' link is up Thu Jan 21 21:34:35 2016 daemon.notice netifd: Interface 'loopback' has link connectivity Thu Jan 21 21:34:36 2016 user.info autossh[1409]: starting ssh (count 1) Thu Jan 21 21:34:36 2016 user.info autossh[1409]: ssh child pid is 1411 Thu Jan 21 21:34:36 2016 user.notice firewall: Reloading firewall due to ifup of lan (br-lan) Thu Jan 21 21:34:38 2016 kern.info kernel: [ 28.170000] eth0: link up (100Mbps/Full duplex) Thu Jan 21 21:34:38 2016 kern.info kernel: [ 28.320000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:34:38 2016 kern.info kernel: [ 28.320000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:34:38 2016 daemon.notice netifd: Network device 'eth0' link is up Thu Jan 21 21:34:38 2016 daemon.notice netifd: Bridge 'br-lan' link is up Thu Jan 21 21:34:38 2016 daemon.notice netifd: Interface 'lan' has link connectivity Thu Jan 21 21:34:39 2016 daemon.notice netifd: radio0 (1353): Configuration file: /var/run/hostapd-phy0.conf Thu Jan 21 21:34:39 2016 kern.info kernel: [ 30.080000] device wlan0 entered promiscuous mode Thu Jan 21 21:34:39 2016 kern.info kernel: [ 30.090000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:34:39 2016 kern.info kernel: [ 30.090000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:34:40 2016 daemon.notice netifd: radio0 (1353): Using interface wlan0 with hwaddr 00:c0:ca:8d:92:b1 and ssid "Pineapple_92B1" Thu Jan 21 21:34:40 2016 daemon.notice netifd: radio0 (1353): wlan0: interface state UNINITIALIZED->ENABLED Thu Jan 21 21:34:40 2016 daemon.notice netifd: radio0 (1353): wlan0: AP-ENABLED Thu Jan 21 21:34:40 2016 kern.info kernel: [ 30.320000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:34:40 2016 kern.info kernel: [ 30.560000] eth0: link down Thu Jan 21 21:34:41 2016 daemon.notice netifd: Network device 'eth0' link is down Thu Jan 21 21:34:41 2016 kern.info kernel: [ 31.560000] br-lan: port 1(eth0) entered disabled state Thu Jan 21 21:34:41 2016 kern.info kernel: [ 32.090000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:34:42 2016 kern.info kernel: [ 32.560000] eth0: link up (100Mbps/Full duplex) Thu Jan 21 21:34:42 2016 kern.info kernel: [ 32.560000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:34:42 2016 kern.info kernel: [ 32.570000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:34:42 2016 daemon.notice netifd: Network device 'eth0' link is up Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: started, version 2.73 cachesize 150 Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: compile time options: no-IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: DNS service limited to local subnets Thu Jan 21 21:34:43 2016 daemon.info dnsmasq-dhcp[1576]: DHCP, IP range 172.16.42.100 -- 172.16.42.249, lease time 12h Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: using local addresses only for domain lan Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: reading /tmp/resolv.conf.auto Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: using local addresses only for domain lan Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: using nameserver 8.8.4.4#53 Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: read /etc/hosts - 1 addresses Thu Jan 21 21:34:43 2016 daemon.info dnsmasq[1576]: read /tmp/hosts/dhcp - 1 addresses Thu Jan 21 21:34:43 2016 daemon.info dnsmasq-dhcp[1576]: read /etc/ethers - 0 addresses Thu Jan 21 21:34:44 2016 kern.info kernel: [ 34.570000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:34:44 2016 user.err autossh[1409]: ssh exited prematurely with status 255; autossh exiting Thu Jan 21 21:34:46 2016 daemon.notice netifd: Network device 'wlan0' link is up Thu Jan 21 21:34:48 2016 daemon.info dnsmasq-dhcp[1576]: DHCPDISCOVER(br-lan) 00:c0:ca:8d:d8:3d Thu Jan 21 21:34:48 2016 daemon.info dnsmasq-dhcp[1576]: DHCPOFFER(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:34:48 2016 daemon.info dnsmasq-dhcp[1576]: DHCPREQUEST(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:34:48 2016 daemon.info dnsmasq-dhcp[1576]: DHCPACK(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:34:58 2016 kern.notice kernel: [ 48.420000] random: nonblocking pool is initialized Thu Jan 21 21:35:13 2016 auth.info sshd[1661]: Server listening on 0.0.0.0 port 22. Thu Jan 21 21:35:13 2016 daemon.err mount_root: no jffs2 marker found Thu Jan 21 21:35:13 2016 kern.warn kernel: [ 63.590000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 Thu Jan 21 21:35:13 2016 kern.warn kernel: [ 63.590000] jffs2_build_filesystem(): unlocking the mtd device... done. Thu Jan 21 21:35:17 2016 auth.err sshd[1695]: error: Could not load host key: /etc/ssh/ssh_host_ecdsa_key Thu Jan 21 21:35:17 2016 auth.err sshd[1695]: error: Could not load host key: /etc/ssh/ssh_host_ed25519_key Thu Jan 21 21:35:23 2016 kern.warn kernel: [ 63.600000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. Thu Jan 21 21:35:23 2016 kern.notice kernel: [ 73.340000] jffs2: notice: (1694) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. Thu Jan 21 21:35:23 2016 daemon.info mount_root: performing overlay whiteout Thu Jan 21 21:35:23 2016 auth.info sshd[1661]: Received signal 15; terminating. Thu Jan 21 21:35:24 2016 kern.info kernel: [ 74.950000] device wlan0 left promiscuous mode Thu Jan 21 21:35:24 2016 kern.info kernel: [ 74.960000] br-lan: port 2(wlan0) entered disabled state Thu Jan 21 21:35:24 2016 daemon.notice netifd: Network device 'wlan0' link is down Thu Jan 21 21:35:25 2016 daemon.err block: /dev/mtdblock3 is already mounted Thu Jan 21 21:35:26 2016 daemon.notice netifd: radio1 (1764): Interface 0 setup failed: BRIDGE_NOT_ALLOWED Thu Jan 21 21:35:26 2016 daemon.notice netifd: radio0 (1827): Configuration file: /var/run/hostapd-phy0.conf Thu Jan 21 21:35:26 2016 daemon.info dnsmasq-dhcp[1576]: DHCPDISCOVER(br-lan) 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:26 2016 daemon.info dnsmasq-dhcp[1576]: DHCPOFFER(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:26 2016 daemon.info dnsmasq-dhcp[1576]: DHCPREQUEST(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:26 2016 daemon.info dnsmasq-dhcp[1576]: DHCPACK(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:27 2016 kern.info kernel: [ 77.130000] device wlan0 entered promiscuous mode Thu Jan 21 21:35:27 2016 kern.info kernel: [ 77.130000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:35:27 2016 kern.info kernel: [ 77.140000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:35:27 2016 daemon.notice netifd: radio0 (1827): Using interface wlan0 with hwaddr 00:c0:ca:8d:92:b1 and ssid "Pineapple_92B1" Thu Jan 21 21:35:27 2016 daemon.notice netifd: radio0 (1827): wlan0: interface state UNINITIALIZED->ENABLED Thu Jan 21 21:35:27 2016 daemon.notice netifd: radio0 (1827): wlan0: AP-ENABLED Thu Jan 21 21:35:27 2016 user.emerg syslog: find: /proc/1954: No such file or directory Thu Jan 21 21:35:27 2016 user.emerg syslog: find: /proc/1957: No such file or directory Thu Jan 21 21:35:27 2016 user.emerg syslog: find: /proc/1958: No such file or directory Thu Jan 21 21:35:28 2016 kern.info kernel: [ 78.710000] usb-storage 1-1.2:1.0: USB Mass Storage device detected Thu Jan 21 21:35:28 2016 kern.info kernel: [ 78.720000] scsi host1: usb-storage 1-1.2:1.0 Thu Jan 21 21:35:28 2016 user.emerg syslog: setting up led wlan0 Thu Jan 21 21:35:29 2016 kern.info kernel: [ 79.140000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:35:29 2016 user.emerg syslog: WiFi Pineapple Controller version 0.1 Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 user.emerg syslog: Usage: pineapple [command] [[options]] [[[args]]] Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 user.emerg syslog: A Program to controll your WiFi Pineapple over the commandline. Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 user.emerg syslog: Commands: Thu Jan 21 21:35:29 2016 user.emerg syslog: karma Thu Jan 21 21:35:29 2016 user.emerg syslog: start - Starts Karma Thu Jan 21 21:35:29 2016 user.emerg syslog: stop - Stops Karma Thu Jan 21 21:35:29 2016 user.emerg syslog: list_ssids - Lists all SSIDs in Karma's black/white list. Thu Jan 21 21:35:29 2016 user.emerg syslog: list_macs - Lists all SSIDs in Karma's black list. Thu Jan 21 21:35:29 2016 user.emerg syslog: add_ssid [SSID] - Adds the specified SSID to the black/white list. Thu Jan 21 21:35:29 2016 user.emerg syslog: del_ssid [SSID] - Delete the specified SSID from the black/white list. Thu Jan 21 21:35:29 2016 user.emerg syslog: add_mac [MAC] - Adds the specified MAC to the black list. Thu Jan 21 21:35:29 2016 user.emerg syslog: del_mac [MAC] - Delete the specified MAC from the black list. Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 user.emerg syslog: led Thu Jan 21 21:35:29 2016 user.emerg syslog: on - Turn's the blue LED on. Thu Jan 21 21:35:29 2016 user.emerg syslog: off - Turn's the blue LED off. Thu Jan 21 21:35:29 2016 user.emerg syslog: reset - Reset's LED behaviour to default Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 user.emerg syslog: module Thu Jan 21 21:35:29 2016 user.emerg syslog: list - Lists all available modules with a CLI component. Thu Jan 21 21:35:29 2016 user.emerg syslog: [Module Name] [[args]] - Runs specified module with args if given. Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 user.emerg syslog: notify [notification text] - Sends a notification to the webinterface Thu Jan 21 21:35:29 2016 user.emerg syslog: Thu Jan 21 21:35:29 2016 daemon.info dnsmasq-dhcp[1576]: DHCPDISCOVER(br-lan) 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:29 2016 daemon.info dnsmasq-dhcp[1576]: DHCPOFFER(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:29 2016 daemon.info dnsmasq-dhcp[1576]: DHCPREQUEST(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:29 2016 daemon.info dnsmasq-dhcp[1576]: DHCPACK(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:29 2016 kern.notice kernel: [ 79.720000] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 0933 PQ: 0 ANSI: 6 Thu Jan 21 21:35:29 2016 kern.notice kernel: [ 79.720000] sd 1:0:0:0: Attached scsi generic sg0 type 0 Thu Jan 21 21:35:29 2016 kern.notice kernel: [ 79.770000] sd 1:0:0:0: [sda] Attached SCSI removable disk Thu Jan 21 21:35:30 2016 daemon.notice netifd: Network device 'wlan0' link is up Thu Jan 21 21:35:30 2016 daemon.info procd: - init complete - Thu Jan 21 21:35:30 2016 daemon.err block: Unkown action change Thu Jan 21 21:35:30 2016 daemon.err block: Unkown action change Thu Jan 21 21:35:36 2016 user.notice root: First Setup: Disable WiFi Thu Jan 21 21:35:36 2016 daemon.notice netifd: Network device 'wlan0' link is down Thu Jan 21 21:35:36 2016 kern.info kernel: [ 86.470000] br-lan: port 2(wlan0) entered disabled state Thu Jan 21 21:35:36 2016 kern.info kernel: [ 86.730000] device wlan0 left promiscuous mode Thu Jan 21 21:35:36 2016 kern.info kernel: [ 86.740000] br-lan: port 2(wlan0) entered disabled state Thu Jan 21 21:35:36 2016 kern.info kernel: [ 86.780000] eth0: link down Thu Jan 21 21:35:37 2016 daemon.notice netifd: Network device 'eth0' link is down Thu Jan 21 21:35:37 2016 kern.info kernel: [ 87.470000] br-lan: port 1(eth0) entered disabled state Thu Jan 21 21:35:38 2016 daemon.notice netifd: Bridge 'br-lan' link is down Thu Jan 21 21:35:38 2016 daemon.notice netifd: Interface 'lan' has link connectivity loss Thu Jan 21 21:35:38 2016 kern.info kernel: [ 88.780000] eth0: link up (100Mbps/Full duplex) Thu Jan 21 21:35:38 2016 kern.info kernel: [ 88.780000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:35:38 2016 kern.info kernel: [ 88.790000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:35:38 2016 daemon.notice netifd: Network device 'eth0' link is up Thu Jan 21 21:35:38 2016 daemon.notice netifd: Bridge 'br-lan' link is up Thu Jan 21 21:35:38 2016 daemon.notice netifd: Interface 'lan' has link connectivity Thu Jan 21 21:35:40 2016 kern.info kernel: [ 90.790000] br-lan: port 1(eth0) entered forwarding state Thu Jan 21 21:35:42 2016 daemon.info dnsmasq-dhcp[1576]: DHCPDISCOVER(br-lan) 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:42 2016 daemon.info dnsmasq-dhcp[1576]: DHCPOFFER(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:42 2016 daemon.info dnsmasq-dhcp[1576]: DHCPREQUEST(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:35:42 2016 daemon.info dnsmasq-dhcp[1576]: DHCPACK(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:38:01 2016 auth.info sshd[2343]: Server listening on 0.0.0.0 port 22. Thu Jan 21 21:38:02 2016 daemon.notice netifd: radio1 (2358): Interface 0 setup failed: BRIDGE_NOT_ALLOWED Thu Jan 21 21:38:02 2016 daemon.notice netifd: radio0 (2357): Configuration file: /var/run/hostapd-phy0.conf Thu Jan 21 21:38:02 2016 kern.info kernel: [ 232.940000] device wlan0 entered promiscuous mode Thu Jan 21 21:38:02 2016 kern.info kernel: [ 232.940000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:38:02 2016 kern.info kernel: [ 232.950000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:38:02 2016 daemon.notice netifd: radio0 (2357): Using interface wlan0 with hwaddr 00:c0:ca:8d:92:b1 and ssid "Pineapple_92B1" Thu Jan 21 21:38:02 2016 kern.info kernel: [ 233.040000] device wlan0-1 entered promiscuous mode Thu Jan 21 21:38:02 2016 kern.info kernel: [ 233.050000] br-lan: port 3(wlan0-1) entered forwarding state Thu Jan 21 21:38:02 2016 kern.info kernel: [ 233.050000] br-lan: port 3(wlan0-1) entered forwarding state Thu Jan 21 21:38:03 2016 daemon.notice netifd: radio0 (2357): Using interface wlan0-1 with hwaddr 02:c0:ca:8d:92:b1 and ssid "chunbks" Thu Jan 21 21:38:03 2016 kern.info kernel: [ 233.570000] br-lan: port 3(wlan0-1) entered disabled state Thu Jan 21 21:38:03 2016 kern.info kernel: [ 233.770000] br-lan: port 3(wlan0-1) entered forwarding state Thu Jan 21 21:38:03 2016 kern.info kernel: [ 233.770000] br-lan: port 3(wlan0-1) entered forwarding state Thu Jan 21 21:38:03 2016 daemon.notice netifd: radio0 (2357): wlan0: interface state UNINITIALIZED->ENABLED Thu Jan 21 21:38:03 2016 daemon.notice netifd: radio0 (2357): wlan0: AP-ENABLED Thu Jan 21 21:38:04 2016 kern.info kernel: [ 234.950000] br-lan: port 2(wlan0) entered forwarding state Thu Jan 21 21:38:05 2016 daemon.info dnsmasq-dhcp[1576]: DHCPDISCOVER(br-lan) 00:c0:ca:8d:d8:3d Thu Jan 21 21:38:05 2016 daemon.info dnsmasq-dhcp[1576]: DHCPOFFER(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:38:05 2016 daemon.info dnsmasq-dhcp[1576]: DHCPREQUEST(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:38:05 2016 daemon.info dnsmasq-dhcp[1576]: DHCPACK(br-lan) 172.16.42.223 00:c0:ca:8d:d8:3d Thu Jan 21 21:38:05 2016 kern.info kernel: [ 235.770000] br-lan: port 3(wlan0-1) entered forwarding state Thu Jan 21 21:38:06 2016 daemon.notice netifd: Network device 'wlan0' link is up Thu Jan 21 21:38:06 2016 daemon.notice netifd: Network device 'wlan0-1' link is up Thu Mar 31 06:50:48 2016 cron.err crond[1328]: time disparity of 99912 minutes detected Thu Mar 31 06:50:53 2016 auth.err sshd[2652]: error: Could not load host key: /etc/ssh/ssh_host_ecdsa_key Thu Mar 31 06:50:53 2016 auth.err sshd[2652]: error: Could not load host key: /etc/ssh/ssh_host_ed25519_key Thu Mar 31 06:51:53 2016 auth.info sshd[2652]: Accepted password for root from 172.16.42.42 port 52056 ssh2 Also, is there a repository of Commands that are applicable for the nano? Other than Googling? I get overwhelmed with information sometimes when I go looking for information. Thank you again.

I can't seem to remember now but is it normal for wlan0 to always go into monitor mode when turning on? I can't seem to get PineAP to work now. It won't enable and I keep seeing wlan0mon on and i can't disable it. Any help would be great. here is my dmesg -Mark [ 0.000000] Linux version 3.18.23 (sebkinne@Worker) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46591) ) #13 Thu Jan 21 13:34:28 PST 2016 [ 0.000000] MyLoader: sysp=8a14b024, boardp=44b65156, parts=b69f8d32 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 80355cf0, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=PINEAPPLE-NANO console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 60944K/65536K available (2465K kernel code, 128K rwdata, 528K rodata, 260K init, 188K bss, 4592K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.100000] NET: Registered protocol family 16 [ 0.100000] MIPS: machine is WiFi Pineapple NANO [ 0.380000] Switched to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.400000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.400000] TCP: reno registered [ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] NET: Registered protocol family 1 [ 0.420000] PCI: CLS 0 bytes, default 32 [ 0.420000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.450000] msgmni has been set to 119 [ 0.460000] io scheduler noop registered [ 0.460000] io scheduler deadline registered (default) [ 0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART [ 0.480000] console [ttyATH0] enabled [ 0.490000] bootconsole [early0] disabled [ 0.500000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.500000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.510000] 5 tp-link partitions found on MTD device spi0.0 [ 0.510000] Creating 5 MTD partitions on "spi0.0": [ 0.520000] 0x000000000000-0x000000020000 : "u-boot" [ 0.520000] 0x000000020000-0x000000134994 : "kernel" [ 0.530000] 0x000000134994-0x000000ff0000 : "rootfs" [ 0.530000] mtd: device 2 (rootfs) set to be root filesystem [ 0.540000] 1 squashfs-split partitions found on MTD device rootfs [ 0.540000] 0x000000db0000-0x000000ff0000 : "rootfs_data" [ 0.550000] 0x000000ff0000-0x000001000000 : "art" [ 0.560000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.590000] libphy: ag71xx_mdio: probed [ 1.190000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.200000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 1.200000] TCP: cubic registered [ 1.200000] NET: Registered protocol family 17 [ 1.210000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.220000] 8021q: 802.1Q VLAN Support v1.8 [ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.240000] Freeing unused kernel memory: 260K (8036f000 - 803b0000) [ 2.640000] init: Console is alive [ 2.640000] init: - watchdog - [ 5.280000] usbcore: registered new interface driver usbfs [ 5.290000] usbcore: registered new interface driver hub [ 5.290000] usbcore: registered new device driver usb [ 5.350000] SCSI subsystem initialized [ 5.360000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.370000] ehci-platform: EHCI generic platform driver [ 5.370000] ehci-platform ehci-platform: EHCI Host Controller [ 5.380000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.390000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 5.410000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 5.410000] hub 1-0:1.0: USB hub found [ 5.410000] hub 1-0:1.0: 1 port detected [ 5.420000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.430000] ohci-platform: OHCI generic platform driver [ 5.440000] uhci_hcd: USB Universal Host Controller Interface driver [ 5.450000] usbcore: registered new interface driver usb-storage [ 5.740000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 5.780000] init: - preinit - [ 6.070000] hub 1-1:1.0: USB hub found [ 6.070000] hub 1-1:1.0: 4 ports detected [ 6.440000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 6.670000] random: procd urandom read with 11 bits of entropy available [ 6.810000] mount_root: loading kmods from internal overlay [ 7.060000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform [ 7.140000] jffs2: notice: (325) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (1 unchecked, 3 orphan) and 12 of xref (0 dead, 9 orphan) found. [ 7.150000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 7.170000] block: extroot: not configured [ 7.210000] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 7.210000] scsi host0: usb-storage 1-1.2:1.0 [ 7.230000] jffs2: notice: (322) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (1 unchecked, 3 orphan) and 12 of xref (0 dead, 9 orphan) found. [ 7.360000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab [ 7.370000] block: extroot: not configured [ 7.380000] mount_root: switching to jffs2 overlay [ 7.450000] procd: - early - [ 7.450000] procd: - watchdog - [ 8.220000] scsi 0:0:0:0: Direct-Access Generic STORAGE DEVICE 0933 PQ: 0 ANSI: 6 [ 8.380000] procd: - ubus - [ 8.770000] sd 0:0:0:0: [sda] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB) [ 8.770000] sd 0:0:0:0: [sda] Write Protect is off [ 8.780000] sd 0:0:0:0: [sda] Mode Sense: 21 00 00 00 [ 8.790000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.810000] sda: sda1 sda2 [ 8.830000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 9.390000] procd: - init - [ 13.680000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 13.690000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 13.760000] cfg80211: Calling CRDA to update world regulatory domain [ 13.800000] cfg80211: World regulatory domain updated: [ 13.800000] cfg80211: DFS Master region: unset [ 13.800000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 13.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 13.820000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 13.830000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 13.840000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 13.850000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 13.860000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 13.870000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 13.870000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 14.090000] ath: EEPROM regdomain: 0x0 [ 14.090000] ath: EEPROM indicates default country code should be used [ 14.090000] ath: doing EEPROM country->regdmn map search [ 14.090000] ath: country maps to regdmn code: 0x3a [ 14.090000] ath: Country alpha2 being used: US [ 14.090000] ath: Regpair used: 0x3a [ 14.100000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 14.100000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 14.110000] cfg80211: Calling CRDA for country: US [ 14.110000] cfg80211: Regulatory domain changed to country: US [ 14.120000] cfg80211: DFS Master region: FCC [ 14.120000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 14.130000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 14.140000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A) [ 14.150000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) [ 14.160000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s) [ 14.170000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 14.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 14.220000] usb 1-1.1: ath9k_htc: Firmware htc_9271.fw requested [ 14.230000] usbcore: registered new interface driver ath9k_htc [ 14.320000] RPC: Registered named UNIX socket transport module. [ 14.320000] RPC: Registered udp transport module. [ 14.320000] RPC: Registered tcp transport module. [ 14.330000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 14.370000] tun: Universal TUN/TAP device driver, 1.6 [ 14.370000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 14.440000] usbcore: registered new interface driver rt2800usb [ 14.450000] usbcore: registered new interface driver rtl8187 [ 14.500000] usbcore: registered new interface driver rtl8192cu [ 14.550000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 14.560000] usbcore: registered new interface driver cdc_acm [ 14.570000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 14.580000] usbcore: registered new interface driver cdc_wdm [ 14.600000] nf_conntrack version 0.5.0 (956 buckets, 3824 max) [ 14.660000] usbcore: registered new interface driver ums-alauda [ 14.680000] usbcore: registered new interface driver ums-cypress [ 14.700000] usbcore: registered new interface driver ums-datafab [ 14.700000] usbcore: registered new interface driver ums-freecom [ 14.710000] usbcore: registered new interface driver ums-isd200 [ 14.720000] usbcore: registered new interface driver ums-jumpshot [ 14.730000] usbcore: registered new interface driver ums-karma [ 14.750000] usb 1-1.1: ath9k_htc: Transferred FW: htc_9271.fw, size: 50980 [ 14.760000] usbcore: registered new interface driver ums-sddr09 [ 14.770000] usbcore: registered new interface driver ums-sddr55 [ 14.790000] usbcore: registered new interface driver ums-usbat [ 14.810000] usbcore: registered new interface driver usbserial [ 14.820000] usbcore: registered new interface driver usbserial_generic [ 14.820000] usbserial: USB Serial support registered for generic [ 14.910000] xt_time: kernel timezone is -0000 [ 14.920000] usbcore: registered new interface driver asix [ 14.940000] usbcore: registered new interface driver cdc_ether [ 14.950000] ip_tables: © 2000-2006 Netfilter Core Team [ 14.980000] usbcore: registered new interface driver pl2303 [ 14.990000] usbserial: USB Serial support registered for pl2303 [ 15.000000] ath9k_htc 1-1.1:1.0: ath9k_htc: HTC initialized with 33 credits [ 15.020000] PPP generic driver version 2.4.2 [ 15.040000] NET: Registered protocol family 24 [ 15.050000] usbcore: registered new interface driver qmi_wwan [ 15.060000] usbcore: registered new interface driver rndis_host [ 15.060000] usbcore: registered new interface driver sierra_net [ 15.080000] usbcore: registered new interface driver option [ 15.080000] usbserial: USB Serial support registered for GSM modem (1-port) [ 16.910000] usb 1-1.2: USB disconnect, device number 4 [ 16.910000] scsi 0:0:0:0: rejecting I/O to offline device [ 16.910000] scsi 0:0:0:0: [sda] killing request [ 16.920000] scsi 0:0:0:0: [sda] [ 16.930000] Result: hostbyte=0x01 driverbyte=0x00 [ 16.930000] scsi 0:0:0:0: [sda] CDB: [ 16.930000] cdb[0]=0x28: 28 00 00 00 00 20 00 00 40 00 [ 16.940000] blk_update_request: I/O error, dev sda, sector 32 [ 16.950000] Buffer I/O error on dev sda, logical block 7, async page read [ 17.860000] ath9k_htc 1-1.1:1.0: ath9k_htc: FW Version: 1.3 [ 17.860000] ath9k_htc 1-1.1:1.0: FW RMW support: Off [ 17.870000] ath: EEPROM regdomain: 0x0 [ 17.870000] ath: EEPROM indicates default country code should be used [ 17.870000] ath: doing EEPROM country->regdmn map search [ 17.870000] ath: country maps to regdmn code: 0x3a [ 17.870000] ath: Country alpha2 being used: US [ 17.870000] ath: Regpair used: 0x3a [ 17.890000] ieee80211 phy1: Atheros AR9271 Rev:1 [ 20.290000] usb 1-1.2: new high-speed USB device number 5 using ehci-platform [ 20.430000] usb-storage 1-1.2:1.0: USB Mass Storage device detected [ 20.460000] scsi host1: usb-storage 1-1.2:1.0 [ 21.660000] scsi 1:0:0:0: Direct-Access Generic STORAGE DEVICE 0933 PQ: 0 ANSI: 6 [ 21.670000] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 22.030000] sd 1:0:0:0: [sda] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB) [ 22.060000] sd 1:0:0:0: [sda] Write Protect is off [ 22.060000] sd 1:0:0:0: [sda] Mode Sense: 21 00 00 00 [ 22.060000] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 22.120000] sda: sda1 sda2 [ 22.160000] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 25.520000] random: nonblocking pool is initialized [ 27.690000] device eth0 entered promiscuous mode [ 33.050000] eth0: link up (100Mbps/Full duplex) [ 33.150000] br-lan: port 1(eth0) entered forwarding state [ 33.160000] br-lan: port 1(eth0) entered forwarding state [ 33.400000] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities [ 33.420000] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities [ 33.510000] EXT4-fs (sda1): recovery complete [ 33.510000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 34.540000] device wlan0 entered promiscuous mode [ 34.660000] Adding 1004024k swap on /dev/sdcard/sd2. Priority:-1 extents:1 across:1004024k [ 34.760000] device wlan0-1 entered promiscuous mode [ 34.780000] br-lan: port 3(wlan0-1) entered forwarding state [ 34.790000] br-lan: port 3(wlan0-1) entered forwarding state [ 35.090000] br-lan: port 2(wlan0) entered forwarding state [ 35.100000] br-lan: port 2(wlan0) entered forwarding state [ 35.160000] br-lan: port 1(eth0) entered forwarding state [ 35.170000] eth0: link down [ 35.330000] br-lan: port 3(wlan0-1) entered disabled state [ 35.570000] br-lan: port 1(eth0) entered disabled state [ 37.100000] br-lan: port 2(wlan0) entered forwarding state [ 37.340000] br-lan: port 3(wlan0-1) entered forwarding state [ 37.340000] br-lan: port 3(wlan0-1) entered forwarding state [ 38.230000] eth0: link up (100Mbps/Full duplex) [ 38.230000] br-lan: port 1(eth0) entered forwarding state [ 38.240000] br-lan: port 1(eth0) entered forwarding state [ 39.340000] br-lan: port 3(wlan0-1) entered forwarding state [ 39.670000] br-lan: port 3(wlan0-1) entered disabled state [ 39.700000] device wlan0-1 left promiscuous mode [ 39.700000] br-lan: port 3(wlan0-1) entered disabled state [ 39.830000] device wlan0 left promiscuous mode [ 39.830000] br-lan: port 2(wlan0) entered disabled state [ 40.240000] br-lan: port 1(eth0) entered forwarding state [ 40.480000] eth0: link down [ 40.720000] br-lan: port 1(eth0) entered disabled state [ 42.170000] device wlan0 entered promiscuous mode [ 42.170000] br-lan: port 2(wlan0) entered forwarding state [ 42.180000] br-lan: port 2(wlan0) entered forwarding state [ 42.570000] device wlan0-1 entered promiscuous mode [ 42.600000] br-lan: port 3(wlan0-1) entered forwarding state [ 42.600000] br-lan: port 3(wlan0-1) entered forwarding state [ 42.720000] br-lan: port 3(wlan0-1) entered disabled state [ 43.480000] eth0: link up (100Mbps/Full duplex) [ 43.480000] br-lan: port 1(eth0) entered forwarding state [ 43.490000] br-lan: port 1(eth0) entered forwarding state [ 44.180000] br-lan: port 2(wlan0) entered forwarding state [ 45.490000] br-lan: port 1(eth0) entered forwarding state [ 45.620000] br-lan: port 3(wlan0-1) entered forwarding state [ 45.630000] br-lan: port 3(wlan0-1) entered forwarding state [ 46.360000] br-lan: port 2(wlan0) entered disabled state [ 46.440000] device wlan0mon entered promiscuous mode [ 47.630000] br-lan: port 3(wlan0-1) entered forwarding state

I think this is a completely different subject from the previous thread, so forgive me is this is double posting. I found this program called auto-reaver for backtrack: https://code.google.com/p/auto-reaver/ I edited it, changing the mon0 to wlan0mon in one of the scripts, titled "wash". I'm trying to edit it to work with kali 2.0. I did what one of the guys in this thread did: https://forums.kali.org/showthread.php?19641-Reaver-WPS-Locked-Situation-and-Useful-Link/page4 And I quote: I know how to do the first part of that and I did. I did both commands. But I'm lost as to how to change all gawk entries to mawk. I'll research it, but I'm asking because when I look at the script, I don't want to screw up the script as is. I want to edit it correctly. There are also some changes I think need to be made to make this backtrack program work for kali 2.0. Could someone explain what I need to read or how to change this properly to fit kali 2.0? There are various scripts.

Hi all, new to the forums. Anyways in short, why can I not change the mac address of mon0? I can change the mac address of wlan1 and wlan0 successfully. But when put in monitor mode, mon0 still has the original mac address of the interface. Say on wlan0 my real mac is 11:11:11:11:11:11 and my spoofed address is 00:11:22:33:44:55. When I put wlan0 into monitor mode it will have the address 11:11:11:11:11:11:00:00:00:00:00... ect. which is normal. But in linux when i run: ifconfig mon0 down macchanger -m 00:11:22:33:44:55 mon0 ifconfig mon0 up I have no problems and my new mac address for mon0 shows up as 00:11:22:33:44:55:00:00:00:00:00:00 etc. (this is on linux with an atheros chipset usb wifi adapter) However on my pineapple if I try to run this same set of commands over ssh i get: Current MAC: 11:11:11:11:11:11 (unknown)ERROR: Can't change MAC: interface up or not permission: Device or resource busy And when I use the network advanced setting on the web interface to change mac address of mon0, it will say it has been set, and it will show the same mac as wlan0 but when i run ifconfig over ssh it still shows me the 11:11:11:11:11:11:00:00:00:00:00 address. Or it shuts down my mon0 completely. Am I missing something here? I looked around and could not find anything. Thank you for any help.

so, i enable wlan0, set the encryption to wpa2, put in my encrypted password, reset the wireless, remove my ethernet connection, adn try to connect wirelessly. it just keeps asking me for the encryption, like it's failing to connect and im very very sure its the right encryption. is it a dhcp issue? if so i tried to manually enter my ip (172.16.42.30), netmask (255.255.255.0), and gateway (172.16.42.1) with no avail. please help?

Hey guys! First off, Kudos to Darren for such a great product and website :) I'm having a slight problem ever since I got the Mark V. I set it up all fine, connected it to my Wifi connection and in the start, I could browse the internet through the eth0 port. But after a day or two, that's changed. Now internet won't work no matter what. At times even the Pineapple bar wouldn't connect to internet. any ideas how I get it to connect to my wifi and the internet to work on the Karma ? I can get devices to connect to it but no internet at all.

Hello, I'd like to hide original pineapple mac addresses, even after a reboot. Of course, by defaut eth0, wlan0 and br-lan have the same mac address (00:13:37:A5:0F:01). So I added in /etc/init.d/network, in start() function : macchanger --mac=01:02:03:04:05:06 eth0 macchanger --mac=01:02:03:04:05:06 wlan0 ...where 01:02:03:04:05:06 is the new mac address I chose. At reboot, the eth0 and br-lan interfaces are well configured, with the 01:02:03:04:05:06 mac address. But the wlan0 interface keeps it's original mac address (00:13:37:A5:0F:01). :( So I tried to fix the wlan0 mac address in /etc/config/wireless, and I used : config wifi-device 'radio0' option type 'mac80211' option hwmode '11ng' option macaddr '01:02:03:04:05:06' [...] But after a reboot the wlan0 interface keeps it's original mac address (00:13:37:A5:0F:01), and in the file /etc/config/wireless new configurations were automatically added at the bottom : config wifi-device 'radio2' option type 'mac80211' option hwmode '11ng' option macaddr '00:13:37:A5:0F:01' [...] config wifi-iface option device 'radio2' [...] So, how to fix the mac address for wlan0, even after a reboot ? Regards.

Ok here is my issue when i try enabling the Wlan0 it does not enable also when i try enabling wlan1 it says enabled but when i refresh it disables again. Could this be a Firmware issue as i just got it. Note I tried Resetting it to factory defaults already. Some Snap Shots http://imgur.com/LHqHFod,JiS3eTd#0 Note Firmware 1.0.4

Hi guys! Yestarday i just got the Mark V and i'm really happy about that. It's been a long waiting till coming in Europe but now here it is. I do have some problems with it. After flashing and so worked perfectly first time and i could see Pineapple_XXXX on range despite the fact my android phone didn't connected auto. Anyway, i think i messed up a bit the things and routing table because i can't understand it anymore and i can't start karma. It just do noting when i try from WUI. I have seen in karma config there is no name for the of wireless networks should stream, i keep add and save with a name but still the same problems. Can somebody first of all help me with routing table and to understand which wlan number works for each thing? Also if i have turned on wlan0 and wlan1 I still can't see any pineapple network in range. I used wiki page but unfortunately there are not so much topics covered there. I was looking also around for some tutorials in the really begging after you boot first time the pineapple. I appreciate any help and explanation and i do hope i will have it working soon. Thanks a lot guys, Alex

I'm having some issues that began immediately after performing a factory reset. My issues pertain primarily to connectivity, client mode, and AutoSSH. Connectivity issues: 1) I cannot connect to my Pineapple AP when I use my Alfa AWUS036NHA (ar9271) USB network adapter with Kali Linux; however, I am able to connect with my Netgear (rtl8187) USB network adapter with Kali Linux. I'm also able to connect with my MacBook Pro, MacBook, and iMac's built-in network adapters. Only when trying to connect with my Alfa, I receive the error- "Unable to obtain an IP address." I've rebooted Kali, rebooted the Pineapple, factory reset the Pineapple, enabled/disabled the radios, changed my Alfa's MAC, and various other things. 2) Prior to performing the first factory reset, I did not have any problems with client mode. After the reset, however, I had the following problems: As soon as I'd use client mode, wlan0 would stop broadcasting permanently and wlan1 would not connect to the wireless network that I selected. To get wlan0 up again, I had to perform a factory reset. Eventually I found that both radios had the same MAC address, so I changed the MACs (in /etc/config/wireless) and the radios began to function again. Now the issue is that all of my Pineapple clients, with the exception of Mac OS X clients (VERY STRANGE), are disconnected immediately after enabling client mode. Issues with AutoSSH: 1) AutoSSH doesn't start on boot or remain persistent 2) If I manually use client mode to connect to a network after a fresh reboot, AutoSSH will not connect to my server although it indicates that it's connected. To get AutoSSH working, here's the procedure that I have to perform: a- Use the client mode tab to connect to the wireless network that I need for internet b- Reboot the Pineapple c- The Pineapple will automatically enable client mode and reconnect to the wireless network that I connected to prior to reboot. d- Click Connect in the AutoSSH tile This gets me connected to my server. However, when managing the Pineapple remotely, I depend on AutoSSH to start on boot and automatically connect after switching between networks in client mode. These issues are very frustrating. Insight is appreciated. Thanks.

Hi all, Having what seems like a problem with the Pineapple and wondering if anyone else has seen this or can offer support... It seems like the radio in my Pineapple isn't functioning properly. After boot up, I can see my Pineapple's SSID but can no longer connect to it. I receive a general connection time-out from BT5, Win7, and Mac OS X. When I enable Karma, I have at least 5 devices in my house that Karma should see including BT5 on an HP Laptop, Windows 7 machine, Linux Machine, an iPhone (I've even got apple's success.html on the pineapple to enable this) and a few others, but it seems that it doesn't detect any clients. These all have a few unsecured and remembered networks. Lastly, I've stopped my wireless, opened the site survey module, enable wlan0 (and then mon0) and tried to scan for APs but none appear (I usually see about 12 with a regular laptop internal wlan). Oh yeah, I also SSHed into it and loaded airodump-ng and that comes up blank too. I've reset cache, factory reset, rebooted, and re-flashed to 2.7.0 (which was my first firmware on the unit.) Thoughts?