Sebkinne Posted August 15, 2018 Share Posted August 15, 2018 Hi everyone, After releasing firmware version 2.3.0 at DEF CON, I hadn't gotten around to creating a forum thread of it yet. As usual, please leave all feedback in this thread. ♥ - The Hak5 Development Team Changelog 2.3.1: Recon Fixed an issue where timed recon scans would fail the first time around. Fixed an issue where the stop handshake capture button would persist after a capture had completed. Changelog 2.3.2 Recon Fixed an issue where performing recon scans would lock up all further PineAP actions. Changelog 2.3.0: Recon Added the ability to capture WPA Handshakes by clicking on the arrow next to a WPA / WPA2 encrypted network. Fixed an issue where multicast MAC addresses were shown as clients to wireless networks. PineAP Fixed an issue where PineAP would remain running when the wlan1mon interface had been removed, causing confusion. Filters Fixed an issue where some combinations of filters did not apply correctly. Logging Fixed an issue where non-completed associations were logged as completed. General Fixed an issue where notifications would show invalid timestamps in Firefox. Fixed an issue that prevented the timezone set during initial Setup from persisting across reboots. Download: Over the air via your WiFi Pineapple's webinterface, or at https://wifipineapple.com/downloads 3 1 Quote Link to comment Share on other sites More sharing options...
keshav1434 Posted August 15, 2018 Share Posted August 15, 2018 Hi after updating not working open said..pls help on it Quote Link to comment Share on other sites More sharing options...
m40295 Posted August 15, 2018 Share Posted August 15, 2018 Thanks seb will check it out Quote Link to comment Share on other sites More sharing options...
theUNK0WN Posted August 16, 2018 Share Posted August 16, 2018 Thanks for the update. Everything that I've reported seems to have been fixed now. However, there might be an issue with PineAP not collecting any essid's into the pool but not 100% sure until I leave out somewhere near people as there's little to no wireless AP's near my home >.> Quote Link to comment Share on other sites More sharing options...
luckman212 Posted August 16, 2018 Share Posted August 16, 2018 Looks like this fw was pulled? I haven't updated yet but I do have the .bin saved on my disk. Any reason this was taken down? Quote Link to comment Share on other sites More sharing options...
Irukandji Posted August 16, 2018 Share Posted August 16, 2018 Maybe there was Really bad bug? Quote Link to comment Share on other sites More sharing options...
Sebkinne Posted August 16, 2018 Author Share Posted August 16, 2018 Nothing big or bad, but there is a bug with Recon / PineAP which we are releasing a fix for tomorrow. Until then, I want to prevent people updating to a bugged update, just to update again. Quote Link to comment Share on other sites More sharing options...
theUNK0WN Posted August 16, 2018 Share Posted August 16, 2018 Hi Sebkinne, Thanks for clarifying this! Saved me some time going out, walking around in the heat ... Quote Link to comment Share on other sites More sharing options...
NazgulAngmar Posted August 16, 2018 Share Posted August 16, 2018 Hi, with version 2.3.0 I had an issue when connected my wifi card ALFA AWUS036NHA to access Internet. All the configuration done under "Access Points" was established to default, losing the configurations done for "Management SSID" "Management PSK" "Disable Management AP" and "Open SSID". It happened only the first time when connected the ALFA card, after reconfigure all the section, the configurations remains even using the ALFA card. Quote Link to comment Share on other sites More sharing options...
NazgulAngmar Posted August 17, 2018 Share Posted August 17, 2018 Hi, in version 2.3.1, 3 unexpected restarts in a period of 3 hours. One of the restarts after the usb connection to my phone and enabling tethering. Quote Link to comment Share on other sites More sharing options...
Just_a_User Posted August 17, 2018 Share Posted August 17, 2018 35 minutes ago, NazgulAngmar said: Hi, in version 2.3.1, 3 unexpected restarts in a period of 3 hours. One of the restarts after the usb connection to my phone and enabling tethering. more likely a power issue, by the sounds of the symptoms anyway 1 Quote Link to comment Share on other sites More sharing options...
Exmix Posted August 17, 2018 Share Posted August 17, 2018 (edited) When I run recon now I end up getting this error. EDIT: Fixed with the 2.3.2 Update ? Thanks guys! Keep up the awesome work. Edited August 21, 2018 by Exmix Quote Link to comment Share on other sites More sharing options...
ACuriousMoose Posted August 31, 2018 Share Posted August 31, 2018 With the latest firmware when I try to download the results of a large recon scan (~30 minutes with lots of SSIDs) I get a 500 error, smaller scans however give me the expected JSON file. Quote Link to comment Share on other sites More sharing options...
simoncfc Posted September 2, 2018 Share Posted September 2, 2018 I am unable to connect to the open SSID I create get a network disabled service rejection or something or other....Never happened until I updated. Also PineAp has to be restarted when wanting to reckon again..... Quote Link to comment Share on other sites More sharing options...
Sebkinne Posted September 2, 2018 Author Share Posted September 2, 2018 20 minutes ago, simoncfc said: I am unable to connect to the open SSID I create get a network disabled service rejection or something or other....Never happened until I updated. Also PineAp has to be restarted when wanting to reckon again..... Are your filters set correctly? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.