Jehu4u Posted August 9, 2018 Share Posted August 9, 2018 Can anyone point me in the right direction? i have a couple USB wifi adapters and i reboot with them attached and they dont show. whats a good know adapter that works with the Tetras? and setup steps as Im sure its not plug and play and select wanX Link to comment Share on other sites More sharing options...
Just_a_User Posted August 9, 2018 Share Posted August 9, 2018 7 minutes ago, Jehu4u said: whats a good know adapter that works with the Tetras? I like using my TL-WN722N V1 with my TETRA as it allows for an external antenna if needed. But also use a Ralink USB WiFi RT5370 now and then. Link to comment Share on other sites More sharing options...
Jehu4u Posted August 9, 2018 Author Share Posted August 9, 2018 4 minutes ago, Just_a_User said: I like using my TL-WN722N V1 with my TETRA as it allows for an external antenna if needed. But also use a Ralink USB WiFi RT5370 now and then. THX! ordered 2 Link to comment Share on other sites More sharing options...
Jehu4u Posted August 13, 2018 Author Share Posted August 13, 2018 So got the TL-WN722N plugged int and no lights. whats the steps to enable this so the Tetra see's it as WAN3 or whatever? Link to comment Share on other sites More sharing options...
Just_a_User Posted August 13, 2018 Share Posted August 13, 2018 3 minutes ago, Jehu4u said: So got the TL-WN722N plugged int and no lights. whats the steps to enable this so the Tetra see's it as WAN3 or whatever? Mine is picked up automagicly... do you not get a wlan2 on netowkring advanced tile or inclient mode? or terminal with a ifconfig? Link to comment Share on other sites More sharing options...
Jehu4u Posted August 13, 2018 Author Share Posted August 13, 2018 nothing, on any of them, no lights or discovery. mines V3 though. poop Link to comment Share on other sites More sharing options...
Just_a_User Posted August 13, 2018 Share Posted August 13, 2018 1 minute ago, Jehu4u said: nothing, on any of them, no lights or discovery. mines V3 though. poop Humm...anything on DMESG? or... can you prove a working device by using on another machine? and also can you confirm a working USB port on the tetra with a USB storage/GPS/4Gmodem/RTL-SDR etc.? Link to comment Share on other sites More sharing options...
Jehu4u Posted August 13, 2018 Author Share Posted August 13, 2018 I have 3 tetras (they keep sending me ones that have power over usb issues) all the same. No activity on reboot while plugged to USB. All stock settings on firmware USB wlans work fine in laptop im on 2.2.0 tplink-wn722n v3 root@Pineapple:~# dmesg [ 0.000000] Linux version 3.18.84 (@40b5f1d45edc) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #135 Wed Jul 4 00:43:07 UTC 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 3 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 803a7cf0, node_mem_map 81000000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=PINEAPPLE-TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125668K/131072K available (2748K kernel code, 126K rwdata, 580K rodata, 184K init, 187K bss, 5404K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] NET: Registered protocol family 16 [ 0.090000] MIPS: machine is WiFi Pineapple TETRA [ 0.100000] ar71xx: using random MAC address for eth0 [ 0.320000] ar71xx: using random MAC address for eth1 [ 0.540000] registering PCI controller with io_map_base unset [ 0.550000] PCI host bridge to bus 0000:00 [ 0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.560000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.570000] pci 0000:00:00.0: [168c:abcd] type 00 class 0x020000 [ 0.570000] pci 0000:00:00.0: invalid calibration data [ 0.570000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit] [ 0.570000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.570000] pci 0000:00:00.0: supports D1 [ 0.570000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.570000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.570000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.580000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.580000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.590000] Switched to clocksource MIPS [ 0.590000] NET: Registered protocol family 2 [ 0.600000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.600000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.610000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.620000] TCP: reno registered [ 0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.630000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.630000] NET: Registered protocol family 1 [ 0.640000] PCI: CLS 0 bytes, default 32 [ 0.640000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.670000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.680000] msgmni has been set to 245 [ 0.690000] io scheduler noop registered [ 0.690000] io scheduler deadline registered (default) [ 0.700000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.710000] console [ttyS0] disabled [ 0.730000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.740000] console [ttyS0] enabled [ 0.750000] bootconsole [early0] disabled [ 0.760000] m25p80 spi0.0: found s25fl008k, expected m25p80 [ 0.760000] m25p80 spi0.0: s25fl008k (1024 Kbytes) [ 0.770000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.770000] Creating 4 MTD partitions on "spi0.0": [ 0.780000] 0x000000000000-0x000000040000 : "u-boot" [ 0.790000] 0x000000040000-0x000000080000 : "u-boot-env" [ 0.790000] 0x000000080000-0x0000000c0000 : "caldata" [ 0.800000] 0x0000000c0000-0x000000100000 : "mb0" [ 0.800000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 0.810000] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit [ 0.820000] nand: 2048MiB, SLC, page size: 4096, OOB size: 224 [ 0.820000] Scanning device for bad blocks [ 1.090000] random: nonblocking pool is initialized [ 1.100000] 2 cmdlinepart partitions found on MTD device ar934x-nfc [ 1.110000] Creating 2 MTD partitions on "ar934x-nfc": [ 1.110000] 0x000000000000-0x000000200000 : "kernel" [ 1.120000] 0x000000200000-0x000080000000 : "ubi" [ 1.130000] libphy: ag71xx_mdio: probed [ 1.730000] ag71xx-mdio.1: Found an AR934X built-in switch [ 1.770000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 2.370000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 2.380000] TCP: cubic registered [ 2.390000] NET: Registered protocol family 17 [ 2.390000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.410000] 8021q: 802.1Q VLAN Support v1.8 [ 2.410000] UBI: auto-attach mtd5 [ 2.420000] UBI: attaching mtd5 to ubi0 [ 13.250000] UBI: fixable bit-flip detected at PEB 3511 [ 14.990000] UBI: fixable bit-flip detected at PEB 4071 [ 15.060000] UBI: scanning is finished [ 15.090000] UBI: attached mtd5 (name "ubi", size 2046 MiB) to ubi0 [ 15.090000] UBI: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes [ 15.100000] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 15.110000] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 15.110000] UBI: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0 [ 15.120000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 15.130000] UBI: max/mean erase counter: 7/1, WL threshold: 4096, image sequence number: 858528783 [ 15.140000] UBI: available PEBs: 0, total reserved PEBs: 4092, PEBs reserved for bad PEB handling: 80 [ 15.150000] UBI: background thread "ubi_bgt0d" started, PID 243 [ 15.150000] UBI: ubiblock0_0 created from ubi0:0(rootfs) [ 15.160000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 15.170000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 15.180000] Freeing unused kernel memory: 184K [ 16.810000] init: Console is alive [ 16.810000] init: - watchdog - [ 18.780000] usbcore: registered new interface driver usbfs [ 18.790000] usbcore: registered new interface driver hub [ 18.790000] usbcore: registered new device driver usb [ 18.840000] SCSI subsystem initialized [ 18.850000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 18.860000] ehci-platform: EHCI generic platform driver [ 18.860000] ehci-platform ehci-platform: EHCI Host Controller [ 18.870000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 18.880000] ehci-platform ehci-platform: TX-TX IDP fix enabled [ 18.890000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 18.910000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 18.910000] hub 1-0:1.0: USB hub found [ 18.920000] hub 1-0:1.0: 1 port detected [ 18.920000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 18.930000] ohci-platform: OHCI generic platform driver [ 18.940000] uhci_hcd: USB Universal Host Controller Interface driver [ 18.950000] usbcore: registered new interface driver usb-storage [ 19.240000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 19.890000] init: - preinit - [ 21.390000] mount_root: loading kmods from internal overlay [ 21.790000] UBIFS: background thread "ubifs_bgt0_1" started, PID 337 [ 22.290000] UBIFS: recovery needed [ 23.090000] UBIFS: recovery completed [ 23.100000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 23.100000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 23.110000] UBIFS: FS size: 2049933312 bytes (1954 MiB, 3972 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs) [ 23.120000] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 23.130000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E2FF6C89-A2DA-4D97-87A3-488200A4C3FE, small LPT model [ 23.140000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 23.170000] block: extroot: not configured [ 23.170000] UBIFS: un-mount UBI device 0, volume 1 [ 23.180000] UBIFS: background thread "ubifs_bgt0_1" stops [ 23.190000] UBIFS: background thread "ubifs_bgt0_1" started, PID 340 [ 24.240000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 24.250000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 24.260000] UBIFS: FS size: 2049933312 bytes (1954 MiB, 3972 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs) [ 24.270000] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 24.280000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E2FF6C89-A2DA-4D97-87A3-488200A4C3FE, small LPT model [ 24.300000] mount_root: loading kmods from internal overlay [ 24.530000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 24.540000] block: extroot: not configured [ 24.550000] mount_root: switching to jffs2 overlay [ 24.600000] procd: - early - [ 24.610000] procd: - watchdog - [ 25.450000] procd: - ubus - [ 26.470000] procd: - init - [ 28.870000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68 [ 28.880000] Backport generated by backports.git backports-20151218-0-g2f58d9d [ 29.000000] ath: EEPROM regdomain: 0x0 [ 29.000000] ath: EEPROM indicates default country code should be used [ 29.000000] ath: doing EEPROM country->regdmn map search [ 29.000000] ath: country maps to regdmn code: 0x3a [ 29.000000] ath: Country alpha2 being used: US [ 29.000000] ath: Regpair used: 0x3a [ 29.010000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 29.010000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47 [ 29.020000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 29.250000] ath: EEPROM regdomain: 0x0 [ 29.250000] ath: EEPROM indicates default country code should be used [ 29.250000] ath: doing EEPROM country->regdmn map search [ 29.250000] ath: country maps to regdmn code: 0x3a [ 29.250000] ath: Country alpha2 being used: US [ 29.250000] ath: Regpair used: 0x3a [ 29.260000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 29.270000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40 [ 29.280000] usbcore: registered new interface driver ath9k_htc [ 29.310000] RPC: Registered named UNIX socket transport module. [ 29.320000] RPC: Registered udp transport module. [ 29.320000] RPC: Registered tcp transport module. [ 29.330000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 29.350000] tun: Universal TUN/TAP device driver, 1.6 [ 29.350000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 29.380000] usbcore: registered new interface driver rt2800usb [ 29.390000] usbcore: registered new interface driver rtl8187 [ 29.410000] usbcore: registered new interface driver rtl8192cu [ 29.450000] usbcore: registered new interface driver cdc_acm [ 29.460000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 29.470000] usbcore: registered new interface driver cdc_wdm [ 29.480000] nf_conntrack version 0.5.0 (1966 buckets, 7864 max) [ 29.510000] usbcore: registered new interface driver ums-alauda [ 29.520000] usbcore: registered new interface driver ums-cypress [ 29.530000] usbcore: registered new interface driver ums-datafab [ 29.540000] usbcore: registered new interface driver ums-freecom [ 29.550000] usbcore: registered new interface driver ums-isd200 [ 29.550000] usbcore: registered new interface driver ums-jumpshot [ 29.560000] usbcore: registered new interface driver ums-karma [ 29.570000] usbcore: registered new interface driver ums-sddr09 [ 29.580000] usbcore: registered new interface driver ums-sddr55 [ 29.590000] usbcore: registered new interface driver ums-usbat [ 29.610000] usbcore: registered new interface driver usbserial [ 29.610000] usbcore: registered new interface driver usbserial_generic [ 29.620000] usbserial: USB Serial support registered for generic [ 29.720000] xt_time: kernel timezone is -0000 [ 29.720000] usbcore: registered new interface driver asix [ 29.730000] usbcore: registered new interface driver ax88179_178a [ 29.740000] usbcore: registered new interface driver cdc_ether [ 29.750000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 29.780000] usbcore: registered new interface driver pl2303 [ 29.790000] usbserial: USB Serial support registered for pl2303 [ 29.800000] PPP generic driver version 2.4.2 [ 29.810000] NET: Registered protocol family 24 [ 29.820000] usbcore: registered new interface driver qmi_wwan [ 29.830000] usbcore: registered new interface driver rndis_host [ 29.850000] usbcore: registered new interface driver sierra_net [ 29.870000] usbcore: registered new interface driver option [ 29.870000] usbserial: USB Serial support registered for GSM modem (1-port) [ 39.550000] device eth1 entered promiscuous mode [ 39.550000] br-lan: port 1(eth1) entered forwarding state [ 39.560000] br-lan: port 1(eth1) entered forwarding state [ 39.690000] br-lan: port 1(eth1) entered disabled state [ 42.300000] eth1: link up (100Mbps/Full duplex) [ 42.300000] br-lan: port 1(eth1) entered forwarding state [ 42.310000] br-lan: port 1(eth1) entered forwarding state [ 44.310000] br-lan: port 1(eth1) entered forwarding state [ 45.100000] device wlan0 entered promiscuous mode [ 45.140000] br-lan: port 2(wlan0) entered forwarding state [ 45.150000] br-lan: port 2(wlan0) entered forwarding state [ 45.200000] device wlan0-1 entered promiscuous mode [ 45.210000] br-lan: port 3(wlan0-1) entered forwarding state [ 45.210000] br-lan: port 3(wlan0-1) entered forwarding state [ 46.240000] br-lan: port 3(wlan0-1) entered disabled state [ 47.150000] br-lan: port 2(wlan0) entered forwarding state [ 47.220000] br-lan: port 3(wlan0-1) entered forwarding state [ 47.220000] br-lan: port 3(wlan0-1) entered forwarding state [ 49.220000] br-lan: port 3(wlan0-1) entered forwarding state [ 66.590000] usb 1-1: USB disconnect, device number 2 [ 68.650000] usb 1-1: new high-speed USB device number 3 using ehci-platform [ 185.890000] eth1: link down [ 185.890000] br-lan: port 1(eth1) entered disabled state [ 187.890000] eth1: link up (100Mbps/Full duplex) [ 187.890000] br-lan: port 1(eth1) entered forwarding state [ 187.900000] br-lan: port 1(eth1) entered forwarding state [ 189.900000] br-lan: port 1(eth1) entered forwarding state [ 194.570000] usb 1-1: USB disconnect, device number 3 [ 197.630000] usb 1-1: new high-speed USB device number 4 using ehci-platform root@Pineapple:~# Link to comment Share on other sites More sharing options...
Jehu4u Posted August 14, 2018 Author Share Posted August 14, 2018 Anyone else pipe in on a know working model with TETRA latest firmware 2.2.0 anything i need to enable for the USB to work ? Link to comment Share on other sites More sharing options...
Just_a_User Posted August 14, 2018 Share Posted August 14, 2018 9 hours ago, Jehu4u said: I have 3 tetras (they keep sending me ones that have power over usb issues) It seems very unlikely (not impossible just unlikely) that hak5 would ship 3x faulty units, if they all have no voltage on the USB port is it possible you have been connecting something that draws more current than the tetras USB port can deliver and popping the VREG inside? Link to comment Share on other sites More sharing options...
Jehu4u Posted August 14, 2018 Author Share Posted August 14, 2018 8 hours ago, Just_a_User said: It seems very unlikely (not impossible just unlikely) that hak5 would ship 3x faulty units, if they all have no voltage on the USB port is it possible you have been connecting something that draws more current than the tetras USB port can deliver and popping the VREG inside? Let me clarify, all 3 do not work with the WiFi adapters. The voltage issues were when running from USB power (micro) using the Y cable to a laptop or battery. When you do recon or a deauth it would reboot With 12 v cord it’s fine. The standard USB2 port will not power on the new tplink USB wlan adapter i have another usb wlan adapter that shows power to its LED but not life beyond that. Link to comment Share on other sites More sharing options...
Just_a_User Posted August 14, 2018 Share Posted August 14, 2018 1 hour ago, Jehu4u said: Let me clarify, Ahh makes much more sense Its most likely a driver issue though. from the wiki - Quote Compatible chipsets include RaLink RT2800 devices, as well as some Atheros and RealTek devices. Wireless adapters from HakShop.com are certified to work with the WiFi Pineapple. The V1 I use is an Atheros device. Link to comment Share on other sites More sharing options...
L07TB0Y Posted August 14, 2018 Share Posted August 14, 2018 I got the wireless card from HAK5 at DEFCON for free and when i plug it in it is automatically recognized as wlan2. The issue i have is the network i want to connect it to is hidden and if i scan it doesnt show up. If i go to the WIRELESS file and manually add config to connect to the hidden wpa2 wireless it does not get an ip or connect. Is there a command i am suppose to run after making changes to the wireless file? Link to comment Share on other sites More sharing options...
Just_a_User Posted August 14, 2018 Share Posted August 14, 2018 23 minutes ago, L07TB0Y said: If i go to the WIRELESS file and manually add config to connect to the hidden wpa2 wireless it does not get an ip or connect. show us your wireless file config (excluding sensitive data)? Link to comment Share on other sites More sharing options...
L07TB0Y Posted August 14, 2018 Share Posted August 14, 2018 had to issue "wifi up wlan2" to get things going after the wireless file change Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.