holgerr Posted January 17, 2014 Share Posted January 17, 2014 Hi, I'm going insane trying to get my Mark V to work properly. There are a number of annoying problems that really prevent it from being useful at the moment. I can only get the second WLAN interface (client mode) to work exactly once after a factory reset. Even then it doesn't work all the time, but at least I usually get it to connect at some point. But as soon as I have to reboot, not only does it not reconnect to the network it was on, but it also doesn't allow me to manually reconnect anymore. It will try, but always fail for no apparent reason and the red light never comes on. If I have the wifimanager infusion installed by that point, it strangely shows me an additional radio interface (radio2) that doesn't have a MAC address and neither does radio1. If I go in through ssh and run the wifi command, it throws an error about a missing hardware interface. If I delete /etc/config/network and recreate it with the wifi command, that still doesn't help. So basically, whenever I need to reboot or move my Pineapple to a different power outlet, I need to start completely from scratch with everything I was doing - makes it pretty useless. I've had a ticket open in the bug tracker about this for almost as long as I've had the device - nobody has even touched it. At the moment it looks as if this device is in an alpha stage of development at best and should not have been sold in the state it's in (not to mention that my firmware SD card was empty, which caused another bit of hassle). Am I the only one who is having these problems - so in other words, does my device maybe have a hardware fault? Or am I the only one who is trying to use both WLAN interfaces the way they are intended to be used and everyone else happily creates an uplink via the ethernet interface? I specifically bought this thing as a lightweight solution for (authorized) penetration testing in circumstances where I need to be able to drop the device and leave it, but with the wifi not reconnecting and reverse-ssh not automatically working either (which doesn't matter since the network connection issue prevents it from being useful), it really feels like I've been sold a lemon instead of a pineapple... Quote Link to comment Share on other sites More sharing options...
RussDR Posted January 17, 2014 Share Posted January 17, 2014 (edited) I've honestly never had this issue before. Not exactly at least. I found I had a similar issue if I used wlan1 to access an AP with a login splash page. I use my Android phone as the interface when I'm mobile and it was getting the AP's login request. I was attempting to login and the Mark V hung then rebooted. I never got a chance to see if Wifi Manager showed additional interfaces but.. After reboot, the Mark V would connect to the same AP and the process would begin again. I would have about 30 seconds or so in the interface or in an SSH and then it would reboot. I found that the only way to make that quit was if I actually logged into the splash page. What I'd say is to try and give us as many variables as possible for how you arrived at your issue and maybe we can recreate it? What type of AP is it? What infusions/scripts/whatever are you running? Any additional peripherals attached to the Mark V? Another thing to keep in mind is not to run too many things at once. I've had my Mark V reboot on me due to that as well. Edited January 17, 2014 by RussDR Quote Link to comment Share on other sites More sharing options...
holgerr Posted January 17, 2014 Author Share Posted January 17, 2014 What I'd say is to try and give us as many variables as possible for how you arrived at your issue and maybe we can recreate it? What type of AP is it? What infusions/scripts/whatever are you running? Any additional peripherals attached to the Mark V? Another thing to keep in mind is not to run too many things at once. I've had my Mark V reboot on me due to that as well. Well, it's quite simple. It happens on every AP I have access to - they all use WPA2 and don't have any login pages. And since it happens right after a factory reset, there are absolutely no infusions, scripts and whatnot running other than what comes with the factory settings. There is also no additional hardware connected (other than my laptop via the eth0 interface, of course). So here is what I do in simple steps: 1) factory reset 2) set root password and reboot 3) log in 4) go to network settings in the web interface 5) go to client mode 6) select appropriate AP and enter PSK (connection quality up to 70/70) 7) click connect 8) wait if something happens - in about 20% of the cases I will get a connection 9) if connection works: reboot 10) wifi client connection won't work at all anymore, so 11) factory reset Quote Link to comment Share on other sites More sharing options...
thesugarat Posted January 17, 2014 Share Posted January 17, 2014 What firmware version are you on? Quote Link to comment Share on other sites More sharing options...
holgerr Posted January 17, 2014 Author Share Posted January 17, 2014 1.0.4 Quote Link to comment Share on other sites More sharing options...
Foxtrot Posted January 17, 2014 Share Posted January 17, 2014 Can you try and connect to an AP, then post your Syslog, Dmesg and output of iwconfig and ifconfig in the spoiler tags please :P Quote Link to comment Share on other sites More sharing options...
RussDR Posted January 17, 2014 Share Posted January 17, 2014 Well, it's quite simple. It happens on every AP I have access to - they all use WPA2 and don't have any login pages. And since it happens right after a factory reset, there are absolutely no infusions, scripts and whatnot running other than what comes with the factory settings. There is also no additional hardware connected (other than my laptop via the eth0 interface, of course). So here is what I do in simple steps: 1) factory reset 2) set root password and reboot 3) log in 4) go to network settings in the web interface 5) go to client mode 6) select appropriate AP and enter PSK (connection quality up to 70/70) 7) click connect 8) wait if something happens - in about 20% of the cases I will get a connection 9) if connection works: reboot 10) wifi client connection won't work at all anymore, so 11) factory reset Hmm. Did you try re-flashing the Mark V? Not factory reset, but re-flash. Quote Link to comment Share on other sites More sharing options...
holgerr Posted January 20, 2014 Author Share Posted January 20, 2014 Can you try and connect to an AP, then post your Syslog, Dmesg and output of iwconfig and ifconfig in the spoiler tags please :P Yes, will do that later today when I'm done working on something else. Quote Link to comment Share on other sites More sharing options...
holgerr Posted January 20, 2014 Author Share Posted January 20, 2014 Hmm. Did you try re-flashing the Mark V? Not factory reset, but re-flash. I did - same result as a factory reset. I even reinstalled the stager. Quote Link to comment Share on other sites More sharing options...
holgerr Posted January 22, 2014 Author Share Posted January 22, 2014 (edited) Can you try and connect to an AP, then post your Syslog, Dmesg and output of iwconfig and ifconfig in the spoiler tags please :P Sorry for the delay - other, more urgent work got in the way. Anyway, here's everything but the syslog contents, since I couldn't find anything useful in /var/log (from what I've seen it looks like there should be a /var/log/messages file, but there isn't...). By the way, this is after I reinstalled the stager, the reflashed the 1.0.4 firmware and then connected to the AP (looks like I connected to the repeater instead of the main access point, but the results are the same with both): root@Pineapple:/etc# iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:"omict" Mode:Managed Frequency:2.457 GHz Access Point: 82:C7:A6:73:B4:44 Bit Rate=36 Mb/s Tx-Power=27 dBm RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=34/70 Signal level=-76 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:404 Invalid misc:3940 Missed beacon:0 wlan0 IEEE 802.11bgn Mode:Master Tx-Power=18 dBm RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. br-lan no wireless extensions. root@Pineapple:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 00:13:37:A5:11:77 inet addr:172.16.42.1 Bcast:172.16.42.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17362 errors:0 dropped:173 overruns:0 frame:0 TX packets:15863 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2405896 (2.2 MiB) TX bytes:5223233 (4.9 MiB) eth0 Link encap:Ethernet HWaddr 00:13:37:A5:11:77 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17676 errors:0 dropped:109 overruns:0 frame:0 TX packets:15863 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2676025 (2.5 MiB) TX bytes:5223233 (4.9 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:667 errors:0 dropped:0 overruns:0 frame:0 TX packets:667 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53110 (51.8 KiB) TX bytes:53110 (51.8 KiB) wlan0 Link encap:Ethernet HWaddr 00:13:37:A5:11:77 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:39678 (38.7 KiB) wlan1 Link encap:Ethernet HWaddr F2:25:AA:AC:A0:DC inet addr:10.10.192.21 Bcast:10.10.192.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13861 errors:0 dropped:292 overruns:0 frame:0 TX packets:11316 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4874649 (4.6 MiB) TX bytes:2097608 (2.0 MiB) [root@mybox ~]# cat pineapple.dmesg [ 0.000000] Linux version 3.3.8 (sebkinne@buildtop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #31 Fri Nov 22 15:47:49 CET 2013 [ 0.000000] MyLoader: sysp=97d936c9, boardp=61b798de, parts=6238a85e [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802d8470, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=MK5 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61596k/65536k available (2124k kernel code, 3940k reserved, 405k data, 208k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79 [ 0.100000] MIPS: machine is MK5 V1.0 [ 0.350000] bio: create slab at 0 [ 0.360000] Switching to clocksource MIPS [ 0.360000] NET: Registered protocol family 2 [ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.370000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.380000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.380000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.390000] TCP reno registered [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] NET: Registered protocol family 1 [ 0.410000] PCI: CLS 0 bytes, default 32 [ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.440000] msgmni has been set to 120 [ 0.440000] io scheduler noop registered [ 0.450000] io scheduler deadline registered (default) [ 0.450000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART [ 0.460000] console [ttyATH0] enabled, bootconsole disabled [ 0.480000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.480000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.490000] 5 tp-link partitions found on MTD device spi0.0 [ 0.490000] Creating 5 MTD partitions on "spi0.0": [ 0.500000] 0x000000000000-0x000000020000 : "u-boot" [ 0.510000] 0x000000020000-0x000000102748 : "kernel" [ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.520000] 0x000000102748-0x000000ff0000 : "rootfs" [ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.540000] mtd: partition "rootfs" set to be root filesystem [ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=BE0000, len=410000 [ 0.550000] 0x000000be0000-0x000000ff0000 : "rootfs_data" [ 0.560000] 0x000000ff0000-0x000001000000 : "art" [ 0.570000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.590000] ag71xx_mdio: probed [ 0.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.160000] TCP cubic registered [ 1.160000] NET: Registered protocol family 17 [ 1.160000] Bridge firewalling registered [ 1.170000] 8021q: 802.1Q VLAN Support v1.8 [ 1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.190000] Freeing unused kernel memory: 208k freed [ 3.680000] Registered led device: mk5:red:wlan1 [ 3.680000] Registered led device: mk5:blue:wlan0 [ 3.680000] Registered led device: mk5:amber:lan [ 6.160000] eth0: link up (100Mbps/Full duplex) [ 6.980000] JFFS2 notice: (421) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (0 unchecked, 2 orphan) and 27 of xref (0 dead, 9 orphan) found. [ 8.010000] SCSI subsystem initialized [ 8.300000] usbcore: registered new interface driver usbfs [ 8.310000] usbcore: registered new interface driver hub [ 8.310000] usbcore: registered new device driver usb [ 8.870000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.880000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 8.880000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 8.920000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 8.940000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 8.940000] hub 1-0:1.0: USB hub found [ 8.940000] hub 1-0:1.0: 1 port detected [ 9.070000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 9.190000] uhci_hcd: USB Universal Host Controller Interface driver [ 9.310000] Initializing USB Mass Storage driver... [ 9.320000] usbcore: registered new interface driver usb-storage [ 9.320000] USB Mass Storage support registered. [ 9.430000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 9.580000] hub 1-1:1.0: USB hub found [ 9.580000] hub 1-1:1.0: 4 ports detected [ 9.860000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 10.090000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform [ 10.220000] scsi0 : usb-storage 1-1.4:1.0 [ 11.220000] scsi 0:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0 [ 11.840000] sd 0:0:0:0: [sda] 3686400 512-byte logical blocks: (1.88 GB/1.75 GiB) [ 11.840000] sd 0:0:0:0: [sda] Write Protect is off [ 11.850000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 11.850000] sd 0:0:0:0: [sda] No Caching mode page present [ 11.850000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.860000] sd 0:0:0:0: [sda] No Caching mode page present [ 11.870000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.870000] sda: sda1 [ 11.880000] sda: p1 size 3686398 extends beyond EOD, enabling native capacity [ 11.890000] sd 0:0:0:0: [sda] No Caching mode page present [ 11.890000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.900000] sda: sda1 [ 11.900000] sda: p1 size 3686398 extends beyond EOD, truncated [ 11.910000] sd 0:0:0:0: [sda] No Caching mode page present [ 11.910000] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 11.920000] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 29.810000] eth0: link down [ 30.820000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5 [ 30.820000] Backport generated by backports.git backports-20130617-4-ge3220f5 [ 30.930000] cfg80211: Calling CRDA to update world regulatory domain [ 30.930000] cfg80211: World regulatory domain updated: [ 30.940000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 30.940000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.950000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 30.960000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 30.970000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.970000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 32.540000] usbcore: registered new interface driver rt73usb [ 32.600000] ath: EEPROM regdomain: 0x0 [ 32.600000] ath: EEPROM indicates default country code should be used [ 32.600000] ath: doing EEPROM country->regdmn map search [ 32.600000] ath: country maps to regdmn code: 0x3a [ 32.600000] ath: Country alpha2 being used: US [ 32.600000] ath: Regpair used: 0x3a [ 32.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 32.610000] Registered led device: ath9k-phy0 [ 32.610000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 32.620000] cfg80211: Calling CRDA for country: US [ 32.620000] cfg80211: Regulatory domain changed to country: US [ 32.620000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 32.630000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 32.640000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 32.650000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 32.660000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 32.660000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 32.670000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 32.700000] usbcore: registered new interface driver rt2800usb [ 32.920000] rtl8187: Invalid hwaddr! Using randomly generated MAC address [ 33.110000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 33.110000] ieee80211 phy1: hwaddr f2:25:aa:ac:a0:dc, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2 [ 33.140000] rtl8187: Customer ID is 0xFF [ 33.140000] Registered led device: rtl8187-phy1::radio [ 33.140000] Registered led device: rtl8187-phy1::tx [ 33.140000] Registered led device: rtl8187-phy1::rx [ 33.140000] rtl8187: wireless switch is on [ 33.140000] usbcore: registered new interface driver rtl8187 [ 33.160000] Button Hotplug driver version 0.4.1 [ 33.380000] RPC: Registered named UNIX socket transport module. [ 33.380000] RPC: Registered udp transport module. [ 33.390000] RPC: Registered tcp transport module. [ 33.390000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 33.650000] PPP generic driver version 2.4.2 [ 33.690000] tun: Universal TUN/TAP device driver, 1.6 [ 33.690000] tun: © 1999-2004 Max Krasnyansky [ 33.950000] ip_tables: © 2000-2006 Netfilter Core Team [ 34.180000] NET: Registered protocol family 24 [ 34.320000] nf_conntrack version 0.5.0 (965 buckets, 3860 max) [ 35.040000] xt_time: kernel timezone is -0000 [ 35.510000] usbcore: registered new interface driver ath9k_htc [ 35.740000] usbcore: registered new interface driver usbserial [ 35.750000] USB Serial support registered for generic [ 35.750000] usbcore: registered new interface driver usbserial_generic [ 35.760000] usbserial: USB Serial Driver core [ 35.900000] usbcore: registered new interface driver asix [ 36.030000] usbcore: registered new interface driver cdc_ether [ 36.150000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 36.260000] usbcore: registered new interface driver rndis_host [ 36.380000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 41.420000] usbcore: deregistering interface driver usbserial_generic [ 41.420000] USB Serial deregistering driver generic [ 41.430000] usbcore: deregistering interface driver usbserial [ 41.470000] usbcore: registered new interface driver usbserial [ 41.470000] USB Serial support registered for generic [ 41.480000] usbcore: registered new interface driver usbserial_generic [ 41.480000] usbserial: USB Serial Driver core [ 42.100000] usbcore: deregistering interface driver usbserial_generic [ 42.110000] USB Serial deregistering driver generic [ 42.110000] usbcore: deregistering interface driver usbserial [ 42.200000] usbcore: registered new interface driver usbserial [ 42.200000] USB Serial support registered for generic [ 42.210000] usbcore: registered new interface driver usbserial_generic [ 42.210000] usbserial: USB Serial Driver core [ 42.930000] usbcore: deregistering interface driver usbserial_generic [ 42.940000] USB Serial deregistering driver generic [ 42.940000] usbcore: deregistering interface driver usbserial [ 43.010000] usbcore: registered new interface driver usbserial [ 43.010000] USB Serial support registered for generic [ 43.020000] usbcore: registered new interface driver usbserial_generic [ 43.030000] usbserial: USB Serial Driver core [ 43.460000] usbcore: deregistering interface driver usbserial_generic [ 43.460000] USB Serial deregistering driver generic [ 43.470000] usbcore: deregistering interface driver usbserial [ 43.520000] usbcore: registered new interface driver usbserial [ 43.520000] USB Serial support registered for generic [ 43.530000] usbcore: registered new interface driver usbserial_generic [ 43.530000] usbserial: USB Serial Driver core [ 44.010000] device eth0 entered promiscuous mode [ 44.610000] eth0: link up (100Mbps/Full duplex) [ 44.610000] br-lan: port 1(eth0) entered forwarding state [ 44.620000] br-lan: port 1(eth0) entered forwarding state [ 46.620000] br-lan: port 1(eth0) entered forwarding state [ 49.190000] device wlan0 entered promiscuous mode [ 49.240000] br-lan: port 2(wlan0) entered forwarding state [ 49.240000] br-lan: port 2(wlan0) entered forwarding state [ 49.950000] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities [ 49.960000] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities [ 49.980000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 51.240000] br-lan: port 2(wlan0) entered forwarding state [ 299.730000] device wlan0 left promiscuous mode [ 299.730000] br-lan: port 2(wlan0) entered disabled state [ 301.400000] device wlan0 entered promiscuous mode [ 301.540000] br-lan: port 2(wlan0) entered forwarding state [ 301.540000] br-lan: port 2(wlan0) entered forwarding state [ 303.540000] br-lan: port 2(wlan0) entered forwarding state [ 309.970000] wlan1: authenticate with 24:65:11:d3:38:7a [ 310.330000] wlan1: send auth to 24:65:11:d3:38:7a (try 1/3) [ 310.340000] wlan1: authenticated [ 310.340000] rtl8187 1-1.1:1.0: wlan1: disabling HT/VHT due to WEP/TKIP use [ 310.360000] wlan1: associate with 24:65:11:d3:38:7a (try 1/3) [ 310.370000] wlan1: RX AssocResp from 24:65:11:d3:38:7a (capab=0x431 status=0 aid=8) [ 310.380000] wlan1: associated [ 315.380000] wlan1: disassociated from 24:65:11:d3:38:7a (Reason: 2) [ 315.480000] wlan1: deauthenticating from 24:65:11:d3:38:7a by local choice (reason=3) [ 315.700000] wlan1: authenticate with 82:c7:a6:73:b4:44 [ 315.870000] wlan1: send auth to 82:c7:a6:73:b4:44 (try 1/3) [ 315.880000] wlan1: authenticated [ 315.880000] rtl8187 1-1.1:1.0: wlan1: disabling HT/VHT due to WEP/TKIP use [ 315.900000] wlan1: associate with 82:c7:a6:73:b4:44 (try 1/3) [ 315.910000] wlan1: RX AssocResp from 82:c7:a6:73:b4:44 (capab=0x431 status=0 aid=3) [ 315.920000] wlan1: associated Jan 22 12:52:29 Pineapple daemon.warn dnsmasq-dhcp[1762]: no address range available for DHCP request via wlan1 Jan 22 12:43:54 Pineapple daemon.warn dnsmasq-dhcp[1762]: no address range available for DHCP request via wlan1 Jan 22 12:43:49 Pineapple daemon.warn dnsmasq-dhcp[1762]: no address range available for DHCP request via wlan1 Jan 22 12:43:49 Pineapple daemon.warn dnsmasq-dhcp[1762]: no address range available for DHCP request via wlan1 Jan 22 12:38:19 Pineapple daemon.warn dnsmasq-dhcp[1762]: no address range available for DHCP request via wlan1 Jan 22 12:34:22 Pineapple cron.err crond[1689]: time disparity of 23173229 minutes detected Jan 1 00:05:29 Pineapple daemon.info dnsmasq[1762]: using local addresses only for domain lan Jan 1 00:05:29 Pineapple daemon.info dnsmasq[1762]: using nameserver 8.8.8.8#53 Jan 1 00:05:29 Pineapple daemon.info dnsmasq[1762]: using nameserver 10.10.192.3#53 Jan 1 00:05:29 Pineapple daemon.info dnsmasq[1762]: using nameserver 10.10.192.1#53 Jan 1 00:05:29 Pineapple daemon.info dnsmasq[1762]: reading /tmp/resolv.conf.auto Jan 1 00:05:28 Pineapple user.notice firewall: Reloading firewall due to ifup of wan (wlan1) Jan 1 00:05:27 Pineapple daemon.notice netifd: Interface 'wan' is now up Jan 1 00:05:27 Pineapple daemon.notice netifd: wan (2612): Lease of 10.10.192.21 obtained, lease time 36000 Jan 1 00:05:27 Pineapple daemon.notice netifd: wan (2612): Sending select for 10.10.192.21... Jan 1 00:05:27 Pineapple daemon.warn dnsmasq-dhcp[1762]: DHCP packet received on wlan1 which has no address Jan 1 00:05:27 Pineapple daemon.warn dnsmasq-dhcp[1762]: DHCP packet received on wlan1 which has no address Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.920000] wlan1: associated Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.910000] wlan1: RX AssocResp from 82:c7:a6:73:b4:44 (capab=0x431 status=0 aid=3) Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.900000] wlan1: associate with 82:c7:a6:73:b4:44 (try 1/3) Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.880000] rtl8187 1-1.1:1.0: wlan1: disabling HT/VHT due to WEP/TKIP use Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.880000] wlan1: authenticated Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.870000] wlan1: send auth to 82:c7:a6:73:b4:44 (try 1/3) Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.700000] wlan1: authenticate with 82:c7:a6:73:b4:44 Jan 1 00:05:15 Pineapple daemon.notice netifd: wan (2612): Sending discover... Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.480000] wlan1: deauthenticating from 24:65:11:d3:38:7a by local choice (reason=3) Jan 1 00:05:15 Pineapple kern.info kernel: [ 315.380000] wlan1: disassociated from 24:65:11:d3:38:7a (Reason: 2) Jan 1 00:05:12 Pineapple daemon.notice netifd: wan (2612): Sending discover... Jan 1 00:05:10 Pineapple kern.info kernel: [ 310.380000] wlan1: associated Jan 1 00:05:10 Pineapple kern.info kernel: [ 310.370000] wlan1: RX AssocResp from 24:65:11:d3:38:7a (capab=0x431 status=0 aid=8) Jan 1 00:05:10 Pineapple kern.info kernel: [ 310.360000] wlan1: associate with 24:65:11:d3:38:7a (try 1/3) Jan 1 00:05:10 Pineapple kern.info kernel: [ 310.340000] rtl8187 1-1.1:1.0: wlan1: disabling HT/VHT due to WEP/TKIP use Jan 1 00:05:10 Pineapple kern.info kernel: [ 310.340000] wlan1: authenticated Jan 1 00:05:10 Pineapple kern.info kernel: [ 310.330000] wlan1: send auth to 24:65:11:d3:38:7a (try 1/3) Jan 1 00:05:09 Pineapple kern.info kernel: [ 309.970000] wlan1: authenticate with 24:65:11:d3:38:7a Jan 1 00:05:09 Pineapple daemon.notice netifd: wan (2612): Sending discover... Jan 1 00:05:09 Pineapple daemon.notice netifd: wan (2612): udhcpc (v1.19.4) started Jan 1 00:05:03 Pineapple kern.info kernel: [ 303.540000] br-lan: port 2(wlan0) entered forwarding state Jan 1 00:05:01 Pineapple kern.info kernel: [ 301.540000] br-lan: port 2(wlan0) entered forwarding state Jan 1 00:05:01 Pineapple kern.info kernel: [ 301.540000] br-lan: port 2(wlan0) entered forwarding state Jan 1 00:05:01 Pineapple kern.info kernel: [ 301.400000] device wlan0 entered promiscuous mode Jan 1 00:04:59 Pineapple kern.info kernel: [ 299.730000] br-lan: port 2(wlan0) entered disabled state Jan 1 00:04:59 Pineapple kern.info kernel: [ 299.730000] device wlan0 left promiscuous mode Jan 1 00:03:12 Pineapple auth.info sshd[1998]: Accepted password for root from 172.16.42.249 port 64881 ssh2 Jan 1 00:03:06 Pineapple auth.info sshd[1998]: WARNING: /etc/ssh/moduli does not exist, using fixed modulus Jan 1 00:01:04 Pineapple user.info sysinit: setting up led wlan1 Jan 1 00:01:04 Pineapple user.info sysinit: setting up led wlan0 Jan 1 00:01:04 Pineapple user.info sysinit: setting up led ethernet Jan 1 00:01:03 Pineapple daemon.info dnsmasq-dhcp[1762]: read /etc/ethers - 0 addresses Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: read /etc/hosts - 1 addresses Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: using local addresses only for domain lan Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: using nameserver 8.8.8.8#53 Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: reading /tmp/resolv.conf.auto Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: using local addresses only for domain lan Jan 1 00:01:03 Pineapple daemon.info dnsmasq-dhcp[1762]: DHCP, IP range 172.16.42.100 -- 172.16.42.249, lease time 12h Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth Jan 1 00:01:03 Pineapple daemon.info dnsmasq[1762]: started, version 2.66 cachesize 150 Jan 1 00:01:00 Pineapple user.notice dnsmasq: Allowing 127.0.0.0/8 responses Jan 1 00:01:00 Pineapple user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses! Jan 1 00:00:57 Pineapple auth.info sshd[1695]: Server listening on 0.0.0.0 port 22. Jan 1 00:00:55 Pineapple cron.info crond[1689]: crond: crond (busybox 1.19.4) started, log level 5 Jan 1 00:00:55 Pineapple user.info sysinit: Failed to start hostapd for phy1 Jan 1 00:00:52 Pineapple user.info sysinit: PHY for wifi device radio1 not found Jan 1 00:00:51 Pineapple kern.info kernel: [ 51.240000] br-lan: port 2(wlan0) entered forwarding state Jan 1 00:00:49 Pineapple kern.info kernel: [ 49.980000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) Jan 1 00:00:49 Pineapple kern.err kernel: [ 49.960000] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities Jan 1 00:00:49 Pineapple kern.err kernel: [ 49.950000] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities Jan 1 00:00:49 Pineapple kern.info kernel: [ 49.240000] br-lan: port 2(wlan0) entered forwarding state Jan 1 00:00:49 Pineapple kern.info kernel: [ 49.240000] br-lan: port 2(wlan0) entered forwarding state Jan 1 00:00:49 Pineapple kern.info kernel: [ 49.190000] device wlan0 entered promiscuous mode Jan 1 00:00:46 Pineapple user.info sysinit: PHY for wifi device radio1 not found Jan 1 00:00:46 Pineapple kern.info kernel: [ 46.620000] br-lan: port 1(eth0) entered forwarding state Jan 1 00:00:45 Pineapple user.info sysinit: PHY for wifi device radio1 not found Jan 1 00:00:44 Pineapple kern.info kernel: [ 44.620000] br-lan: port 1(eth0) entered forwarding state Jan 1 00:00:44 Pineapple kern.info kernel: [ 44.610000] br-lan: port 1(eth0) entered forwarding state Jan 1 00:00:44 Pineapple kern.info kernel: [ 44.610000] eth0: link up (100Mbps/Full duplex) Jan 1 00:00:44 Pineapple user.notice firewall: Reloading firewall due to ifup of lan (br-lan) Jan 1 00:00:44 Pineapple daemon.notice netifd: Interface 'loopback' is now up Jan 1 00:00:44 Pineapple daemon.notice netifd: Interface 'lan' is now up Jan 1 00:00:44 Pineapple kern.info kernel: [ 44.010000] device eth0 entered promiscuous mode Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.530000] usbserial: USB Serial Driver core Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.530000] usbcore: registered new interface driver usbserial_generic Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.520000] USB Serial support registered for generic Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.520000] usbcore: registered new interface driver usbserial Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.470000] usbcore: deregistering interface driver usbserial Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.460000] USB Serial deregistering driver generic Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.460000] usbcore: deregistering interface driver usbserial_generic Jan 1 00:00:43 Pineapple user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Generic Product=Mass_Storage_Device Serial=058F0O1111B1 Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.030000] usbserial: USB Serial Driver core Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.020000] usbcore: registered new interface driver usbserial_generic Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.010000] USB Serial support registered for generic Jan 1 00:00:43 Pineapple kern.info kernel: [ 43.010000] usbcore: registered new interface driver usbserial Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.940000] usbcore: deregistering interface driver usbserial Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.940000] USB Serial deregistering driver generic Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.930000] usbcore: deregistering interface driver usbserial_generic Jan 1 00:00:42 Pineapple user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=Realtek Product=RTL8187_Wireless_LAN_Adapter Serial=00e04c000001 Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.210000] usbserial: USB Serial Driver core Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.210000] usbcore: registered new interface driver usbserial_generic Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.200000] USB Serial support registered for generic Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.200000] usbcore: registered new interface driver usbserial Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.110000] usbcore: deregistering interface driver usbserial Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.110000] USB Serial deregistering driver generic Jan 1 00:00:42 Pineapple kern.info kernel: [ 42.100000] usbcore: deregistering interface driver usbserial_generic Jan 1 00:00:42 Pineapple user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0Hub Serial=? Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.480000] usbserial: USB Serial Driver core Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.480000] usbcore: registered new interface driver usbserial_generic Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.470000] USB Serial support registered for generic Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.470000] usbcore: registered new interface driver usbserial Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.430000] usbcore: deregistering interface driver usbserial Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.420000] USB Serial deregistering driver generic Jan 1 00:00:41 Pineapple kern.info kernel: [ 41.420000] usbcore: deregistering interface driver usbserial_generic Jan 1 00:00:41 Pineapple user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform Jan 1 00:00:38 Pineapple kern.notice kernel: [ 36.380000] sd 0:0:0:0: Attached scsi generic sg0 type 0 Jan 1 00:00:38 Pineapple kern.info kernel: [ 36.260000] usbcore: registered new interface driver rndis_host Jan 1 00:00:38 Pineapple kern.err kernel: [ 36.150000] Error: Driver 'gpio-keys-polled' is already registered, aborting... Jan 1 00:00:38 Pineapple kern.info kernel: [ 36.030000] usbcore: registered new interface driver cdc_ether Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.900000] usbcore: registered new interface driver asix Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.760000] usbserial: USB Serial Driver core Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.750000] usbcore: registered new interface driver usbserial_generic Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.750000] USB Serial support registered for generic Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.740000] usbcore: registered new interface driver usbserial Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.510000] usbcore: registered new interface driver ath9k_htc Jan 1 00:00:38 Pineapple kern.info kernel: [ 35.040000] xt_time: kernel timezone is -0000 Jan 1 00:00:38 Pineapple kern.info kernel: [ 34.320000] nf_conntrack version 0.5.0 (965 buckets, 3860 max) Jan 1 00:00:38 Pineapple kern.info kernel: [ 34.180000] NET: Registered protocol family 24 Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.950000] ip_tables: © 2000-2006 Netfilter Core Team Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.690000] tun: © 1999-2004 Max Krasnyansky Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.690000] tun: Universal TUN/TAP device driver, 1.6 Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.650000] PPP generic driver version 2.4.2 Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.390000] RPC: Registered tcp NFSv4.1 backchannel transport module. Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.390000] RPC: Registered tcp transport module. Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.380000] RPC: Registered udp transport module. Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.380000] RPC: Registered named UNIX socket transport module. Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.160000] Button Hotplug driver version 0.4.1 Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.140000] usbcore: registered new interface driver rtl8187 Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.140000] rtl8187: wireless switch is on Jan 1 00:00:38 Pineapple kern.debug kernel: [ 33.140000] Registered led device: rtl8187-phy1::rx Jan 1 00:00:38 Pineapple kern.debug kernel: [ 33.140000] Registered led device: rtl8187-phy1::tx Jan 1 00:00:38 Pineapple kern.debug kernel: [ 33.140000] Registered led device: rtl8187-phy1::radio Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.140000] rtl8187: Customer ID is 0xFF Jan 1 00:00:38 Pineapple kern.info kernel: [ 33.110000] ieee80211 phy1: hwaddr f2:25:aa:ac:a0:dc, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2 Jan 1 00:00:38 Pineapple kern.debug kernel: [ 33.110000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' Jan 1 00:00:38 Pineapple kern.warn kernel: [ 32.920000] rtl8187: Invalid hwaddr! Using randomly generated MAC address Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.700000] usbcore: registered new interface driver rt2800usb Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.670000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.660000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.660000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.650000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.640000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.630000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.620000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.620000] cfg80211: Regulatory domain changed to country: US Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.620000] cfg80211: Calling CRDA for country: US Jan 1 00:00:38 Pineapple kern.info kernel: [ 32.610000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 Jan 1 00:00:38 Pineapple kern.debug kernel: [ 32.610000] Registered led device: ath9k-phy0 Edited January 22, 2014 by holgerr Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.