crepsidro Posted December 7, 2013 Share Posted December 7, 2013 Ok, after almost a year i finally have a setup as close to 'working' as it can get on that piece of...engineering (mk4). The ONLY way for it to work and not reboot at the fisrt sign of any real load is: Anker 14400mah 12v output to -> Mk4 Mk4 USB -> 4 port usb hub (NON POWERED!!!) 4 port hub -> 2gb flash stick (NOT SANDISK!!!!) -> 3g stick -> NHA from 'elite' set This way it works - jammer is running on wlan1, karma and sslstrip on wlan0+3g, two reverse ssh tunnels (shell and webface). Powered hub = fail. Any other power source (non a/c) = fail. Sandisk stick = fail. Hope this helps, as there's still no updates from the team. Oh, and it's on 2.8.1. 3.0 was stillborn... Quote Link to comment Share on other sites More sharing options...
crepsidro Posted December 7, 2013 Author Share Posted December 7, 2013 (edited) Also i had to change the fstab mount config to allow usb stick to always be mounted properly. I had it pop up as sda or sdb randomly, so i decided to go with uuid. Issue 'blkid' command to list the current volumes uuids (stick have to be mounted at this point). Edit fstab (/etc/config) and comment out 'option device /dev/sd*' lines and replace with corresponding 'option uuid '[uuid here]' lines for /usb and swap volumes. That works great and now my stick gets mounted regardless of physical device id. This also introduces some additional security so to speak - any other usb stick will not mount. If you need to change to another stick - edit fstab again to temporarily use 'option device /dev/sd?' lines again, mount, blkid, edit fstab. Cheers Edited December 7, 2013 by crepsidro Quote Link to comment Share on other sites More sharing options...
Foxtrot Posted December 7, 2013 Share Posted December 7, 2013 Ok, after almost a year i finally have a setup as close to 'working' as it can get on that piece of...engineering (mk4). The ONLY way for it to work and not reboot at the fisrt sign of any real load is: Anker 14400mah 12v output to -> Mk4 Mk4 USB -> 4 port usb hub (NON POWERED!!!) 4 port hub -> 2gb flash stick (NOT SANDISK!!!!) -> 3g stick -> NHA from 'elite' set Not true. I run my Mark IV with a Anker 10000mah 9v output, and it works fine. I use a D-Link 4 Port Powered Hub with a 3G Modem, and two USBs, one is a sandisk, again, works fine and dandy. Oh, and it's on 2.8.1. 3.0 was stillborn... 3.0 wasnt a stable release ;) Quote Link to comment Share on other sites More sharing options...
crepsidro Posted December 7, 2013 Author Share Posted December 7, 2013 Not true. I run my Mark IV with a Anker 10000mah 9v output, and it works fine. I use a D-Link 4 Port Powered Hub with a 3G Modem, and two USBs, one is a sandisk, again, works fine and dandy. Try adding NHA that was supplied with elite set ))) Without NHA i can run it all just off 1A usb port.... Quote Link to comment Share on other sites More sharing options...
Foxtrot Posted December 7, 2013 Share Posted December 7, 2013 Well what do you expect? Quote Link to comment Share on other sites More sharing options...
crepsidro Posted December 7, 2013 Author Share Posted December 7, 2013 (edited) I didn't expect anything. I found the working setup by trial and error. Oh, wait. I remember ordering the 'elite SET' hoping it'll include working setup. With likkle pineapple juice, powerhungry sandisk, 500mw nha an' all ;) I guess you can call that 'expectations'. Or was it false advertising? ;) Edited December 7, 2013 by crepsidro Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.