MKIV & OS X Mountain Lion issues

[securitycrush]

So we've recently acquired a handful of the MKIV's for work and I'm trying to get it to work on my Air.

Trying to set it up to my Air, I've set the following:

In Service Order:

Wi-Fi:

Configure IPv4: Using DHCP

IPv4 Address: 192.168.1.10

Subnet Mask: 255.255.255.0

Router: 192.168.1.1

DNS: 8.8.8.8

Thunderbolt Ethernet

Configure IPv4: Manually

IP Address: 172.16.42.42

Subnet Mask: 255.255.255.0

DNS: 8.8.8.8

Internet Sharing: On (Thunderbolt Ethernet)

I tried running the wp4.sh through terminal and it hangs after entering the last prompt, I have to CTRL+C to get out of it.

I've also tried setting it up within Ubuntu 12.04 using the wp4.sh script within a VM with 2 bridged adapters setup for wireless and ethernet, however, only one will connect and the other constantly flashes in the status bar saying not connect (ethernet).

Pinging 172.16.42.1 does not work.

I can use my wireless no problem, however, for some reason ethernet is not working - even with wireless off just to see if that matters. I've attached my network settings for my Air below. I've tried both in the WAN and PoE/LAN ports.

MacBook-Air:jasegar SECAir$ ifconfig
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether b8:8d:12:0e:2a:c8
inet6 fe80::ba8d:12ff:fe0e:2ac8%en0 prefixlen 64 scopeid 0x4
inet 192.168.1.10 netmask 0xffffff00 broadcast 192.168.1.255
media: autoselect
status: active[/font][/color]

[color=#282828][font=helvetica, arial, sans-serif]p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
ether 0a:8d:12:0e:2a:c8
media: autoselect
status: inactive[/font][/color]

[color=#282828][font=helvetica, arial, sans-serif]en2: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=b<RXCSUM,TXCSUM,VLAN_HWTAGGING>
ether 40:6c:8f:37:8c:0e
inet6 fe80::426c:8fff:fe37:8c0e%en2 prefixlen 64 scopeid 0x6
media: autoselect (100baseTX <full-duplex,flow-control>)
status: active[/font][/color]

[color=#282828][font=helvetica, arial, sans-serif]bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether ac:de:48:29:88:19
inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255
Configuration:
priority 0 hellotime 0 fwddelay 0 maxage 0
ipfilter disabled flags 0x2
member: en2 flags=3<LEARNING,DISCOVER>
		 port 6 priority 0 path cost 0
[/CODE]

[/font][/color]

[barry99705]

bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500

ether ac:de:48:29:88:19

inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255

Configuration:

priority 0 hellotime 0 fwddelay 0 maxage 0

ipfilter disabled flags 0x2

member: en2 flags=3<LEARNING,DISCOVER>

port 6 priority 0 path cost 0

This is your problem.

[securitycrush]

bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500

ether ac:de:48:29:88:19

inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255

Configuration:

priority 0 hellotime 0 fwddelay 0 maxage 0

ipfilter disabled flags 0x2

member: en2 flags=3<LEARNING,DISCOVER>

port 6 priority 0 path cost 0

This is your problem.

Thanks barry - I will try to figure out why its not setting properly, even when I go into my Network settings and set it the right way. For some reason it's not changing the config.

[tertko]

in mountain lion you can only share net if your network is at 192.168.2.0

you cannot change that

[thesugarat]

Check this out too.