Jump to content

Jashmane

Active Members
  • Posts

    11
  • Joined

  • Last visited

Recent Profile Visitors

636 profile views

Jashmane's Achievements

Newbie

Newbie (1/14)

  1. Yea i'm going to do that, could you send me to the right thread to do that. thnks for the help
  2. I'll try to set it to 192.168.2.11. But yea iv'e already tried to set it to .100 but i'm geting the same error
  3. Yes i have watched it many time's and i'm still getting stuck at the part of putty not connecting to the Tftpd server
  4. Problem with flashing over Serial PLZ HELP Iv'e done every step by step to do a clean flash over TTL UART OVER SERIAL because iv'e bricked it. Iv'e set the local area connection to iP 192.168.2.11 for the pinapple Iv'e set the same IP on Tftpd server. Iv'e set up putty right, serial line COM3 speed 115200, even in the serial tab flow control none. but putty is where i'm having a problem. once i open it i choosed 1, then i open Trtpd64 server I set my server interface to 192.168.2.11 change my dir to the factory files i run in putty "setenv bootargs "board=ALFA console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd" "saveenv" "tftp 0x80600000 kernel.bin" < this is where i get stuck! putty say's ar7240> tftp 0x80600000 kernel.bin eth0 link down FAIL dup 1 speed 1000 Using eth1 device TFTP from server "192.168.2.100";<(problem it should be 192.168.2.11) our IP address is 192.168.2.1 Filename 'kernel.bin'. Load address: 0x80600000 Loading: T T T T T T T T T T Retry count exceeded; starting again eth0 link down FAIL I can't get Putty to use the 192.168.2.11 it try's to connect to 192.168.2.100. on Putty Iv'e tried everything i can think of PLZ HELP THNKS ALOT (I miss playing around with my Wifi pineapple I was learning alot)I have set everything up right put for some reason putty will not connect to the Tftpd64 server, Iv'e ever tried to set the pineapple to the ip that putty's trying to connect to " 192.168.2.100" still no luck, it just wont connect to the server. IF ANYBODY HAS A IDEA HOW TO HELP ME FLASH MY PINEAPPLE OVER Serial IT WOULD MEAN ALOT TO ME THNKS
  5. problem's with flashing over TTL UART OVER SERIAL Iv'e done every step by step to do a clean flash over TTL UART OVER SERIAL because iv'e bricked it. Iv'e set the local area connection to iP 192.168.2.11 for the pinapple Iv'e set the same IP on Tftpd server. Iv'e set up putty right, serial line COM3 speed 115200, even in the serial tab flow control none. but putty is where i'm having a problem. once i open it i choosed 1, then i open Trtpd64 server I set my server interface to 192.168.2.11 change my dir to the factory files i run in putty "setenv bootargs "board=ALFA console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd" "saveenv" "tftp 0x80600000 kernel.bin" < this is where i get stuck! putty say's ar7240> tftp 0x80600000 kernel.bin eth0 link down FAIL dup 1 speed 1000 Using eth1 device TFTP from server "192.168.2.100";<(problem it should be 192.168.2.11) our IP address is 192.168.2.1 Filename 'kernel.bin'. Load address: 0x80600000 Loading: T T T T T T T T T T Retry count exceeded; starting again eth0 link down FAIL I can't get Putty to use the 192.168.2.11 it try's to connect to 192.168.2.100. on Putty Iv'e tried everything i can think of PLZ HELP THNKS ALOT (I miss playing around with my Wifi pineapple I was learning alot)
  6. Fixing my Pineapple IV Over Serial

×
×
  • Create New...