Jump to content

Search the Community

Showing results for tags 'clean flash over TTL UART'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 1 result

  1. Problem with flashing over Serial PLZ HELP Iv'e done every step by step to do a clean flash over TTL UART OVER SERIAL because iv'e bricked it. Iv'e set the local area connection to iP 192.168.2.11 for the pinapple Iv'e set the same IP on Tftpd server. Iv'e set up putty right, serial line COM3 speed 115200, even in the serial tab flow control none. but putty is where i'm having a problem. once i open it i choosed 1, then i open Trtpd64 server I set my server interface to 192.168.2.11 change my dir to the factory files i run in putty "setenv bootargs "board=ALFA console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd" "saveenv" "tftp 0x80600000 kernel.bin" < this is where i get stuck! putty say's ar7240> tftp 0x80600000 kernel.bin eth0 link down FAIL dup 1 speed 1000 Using eth1 device TFTP from server "192.168.2.100";<(problem it should be 192.168.2.11) our IP address is 192.168.2.1 Filename 'kernel.bin'. Load address: 0x80600000 Loading: T T T T T T T T T T Retry count exceeded; starting again eth0 link down FAIL I can't get Putty to use the 192.168.2.11 it try's to connect to 192.168.2.100. on Putty Iv'e tried everything i can think of PLZ HELP THNKS ALOT (I miss playing around with my Wifi pineapple I was learning alot)I have set everything up right put for some reason putty will not connect to the Tftpd64 server, Iv'e ever tried to set the pineapple to the ip that putty's trying to connect to " 192.168.2.100" still no luck, it just wont connect to the server. IF ANYBODY HAS A IDEA HOW TO HELP ME FLASH MY PINEAPPLE OVER Serial IT WOULD MEAN ALOT TO ME THNKS
×
×
  • Create New...