HomerJS Posted December 29, 2019 Share Posted December 29, 2019 Hi everybody, i am new here. I get my WIFI Pineapple Tetra last week 🙂 Now i tried to use my AWUS036NHA with my tetra. It should be used for the client WIFI mode. When i put in the wifi adapter the tetra reconize it and i see wlan 2 under the interfaces. the scan for ssids is also posible. the led of the wifi adapter is solid blue. When i choose my ssid an try to connect the wlan the led of the wifi adapter starts to blink, but a connection is not established. After a sccond try interface changed to wlan1. after that i can not choose wlan2 any more. in the interface overview, wlan2 is still there. With wlan1 everything works fine. I tried also an shorter cable (about 40-50 cm) and a second wifi adapter from the same typ. Did anybody have an idea to solve my problem ? Best regards HomerJS Here is the dmesg output [ 0.000000] Linux version 4.14.134 (@149e44b6b356) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r0+10558-a2cbcfcdff)) #0 Tue Oct 8 15:43:02 2019 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 3 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 805481e0, node_mem_map 81000020 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x478 with crng_init=0 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=PINEAPPLE-TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 124044K/131072K available (3962K kernel code, 169K rwdata, 896K rodata, 212K init, 205K bss, 7028K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 51 [ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6825930166 ns [ 0.000009] sched_clock: 32 bits at 280MHz, resolution 3ns, wraps every 7669584382ns [ 0.008311] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.084943] pid_max: default: 32768 minimum: 301 [ 0.090077] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.097137] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.106916] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.117433] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.124423] NET: Registered protocol family 16 [ 0.130565] MIPS: machine is Hak5 WiFi Pineapple TETRA [ 0.136314] ar71xx: using random MAC address for eth0 [ 0.369488] ar71xx: using random MAC address for eth1 [ 0.613882] registering PCI controller with io_map_base unset [ 0.636149] PCI host bridge to bus 0000:00 [ 0.640580] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.647892] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.653836] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.661055] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.669535] pci 0000:00:00.0: [168c:abcd] type 00 class 0x020000 [ 0.669552] pci 0000:00:00.0: invalid calibration data [ 0.675055] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit] [ 0.675112] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.675194] pci 0000:00:00.0: supports D1 [ 0.675206] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.675422] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.675451] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.683285] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.691624] clocksource: Switched to clocksource MIPS [ 0.698118] NET: Registered protocol family 2 [ 0.703569] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.711002] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.717827] TCP: Hash tables configured (established 1024 bind 1024) [ 0.724733] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.730967] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.737936] NET: Registered protocol family 1 [ 0.742658] PCI: CLS 0 bytes, default 32 [ 0.747535] Crashlog allocated RAM at address 0x3f00000 [ 0.754489] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.766403] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.772657] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.793550] io scheduler noop registered [ 0.797727] io scheduler deadline registered (default) [ 0.803614] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.810762] console [ttyS0] disabled [ 0.834673] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.843869] console [ttyS0] enabled [ 0.851276] bootconsole [early0] disabled [ 0.863564] m25p80 spi0.0: found s25fl008k, expected m25p80 [ 0.879081] m25p80 spi0.0: s25fl008k (1024 Kbytes) [ 0.883999] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.890005] Creating 4 MTD partitions on "spi0.0": [ 0.894893] 0x000000000000-0x000000040000 : "u-boot" [ 0.901714] 0x000000040000-0x000000080000 : "u-boot-env" [ 0.908516] 0x000000080000-0x0000000c0000 : "caldata" [ 0.915754] 0x0000000c0000-0x000000100000 : "mb0" [ 0.923451] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 0.929907] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit [ 0.935516] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 0.943438] Scanning device for bad blocks [ 0.953146] random: fast init done [ 1.217496] 2 cmdlinepart partitions found on MTD device ar934x-nfc [ 1.223867] Creating 2 MTD partitions on "ar934x-nfc": [ 1.229092] 0x000000000000-0x000000200000 : "kernel" [ 1.235528] 0x000000200000-0x000080000000 : "ubi" [ 1.245813] libphy: Fixed MDIO Bus: probed [ 1.261750] libphy: ag71xx_mdio: probed [ 1.893506] ag71xx-mdio.1: Found an AR934X built-in switch [ 1.945683] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 2.583602] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 2.593490] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 2.601357] NET: Registered protocol family 10 [ 2.610517] Segment Routing with IPv6 [ 2.614406] NET: Registered protocol family 17 [ 2.619540] 8021q: 802.1Q VLAN Support v1.8 [ 2.628064] UBI: auto-attach mtd5 [ 2.631462] ubi0: attaching mtd5 [ 4.103596] random: crng init done [ 15.211872] ubi0: scanning is finished [ 15.240209] ubi0: attached mtd5 (name "ubi", size 2046 MiB) [ 15.245924] ubi0: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes [ 15.252914] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 15.259802] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 15.266869] ubi0: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0 [ 15.273064] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 15.280396] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2111571258 [ 15.289670] ubi0: available PEBs: 0, total reserved PEBs: 4092, PEBs reserved for bad PEB handling: 80 [ 15.299173] ubi0: background thread "ubi_bgt0d" started, PID 294 [ 15.307160] block ubiblock0_0: created from ubi0:0(rootfs) [ 15.312792] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 15.328360] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 15.336744] Freeing unused kernel memory: 212K [ 15.341250] This architecture does not have kernel memory protection. [ 15.926856] init: Console is alive [ 15.930557] init: - watchdog - [ 17.822831] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 18.014032] usbcore: registered new interface driver usbfs [ 18.019670] usbcore: registered new interface driver hub [ 18.025221] usbcore: registered new device driver usb [ 18.069648] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 18.086869] SCSI subsystem initialized [ 18.096395] ehci-platform: EHCI generic platform driver [ 18.101857] ehci-platform ehci-platform: EHCI Host Controller [ 18.107721] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 18.117861] ehci-platform ehci-platform: TX-TX IDP fix enabled [ 18.123839] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 18.151670] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 18.158859] hub 1-0:1.0: USB hub found [ 18.163132] hub 1-0:1.0: 1 port detected [ 18.170840] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 18.178893] ohci-platform: OHCI generic platform driver [ 18.186974] uhci_hcd: USB Universal Host Controller Interface driver [ 18.198442] usbcore: registered new interface driver usb-storage [ 18.205314] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 18.215232] init: - preinit - [ 19.286934] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 19.521101] mount_root: loading kmods from internal overlay [ 19.574366] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 19.586976] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 19.852469] UBIFS (ubi0:1): default file-system created [ 19.859214] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 401 [ 20.632214] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 20.640171] UBIFS (ubi0:1): LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 20.650266] UBIFS (ubi0:1): FS size: 2048901120 bytes (1953 MiB, 3970 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs) [ 20.661484] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 20.668212] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID B68B723A-8996-4F3B-90B4-085F569C440A, small LPT model [ 20.682273] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 20.689540] block: unable to load configuration (fstab: Entry not found) [ 20.696509] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 20.703343] block: unable to load configuration (fstab: Entry not found) [ 20.710243] block: attempting to load /etc/config/fstab [ 20.717625] block: unable to load configuration (fstab: Entry not found) [ 20.724586] block: no usable configuration [ 20.733657] UBIFS (ubi0:1): un-mount UBI device 0 [ 20.738501] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops [ 20.751064] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 404 [ 21.515950] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 21.523947] UBIFS (ubi0:1): LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 21.534016] UBIFS (ubi0:1): FS size: 2048901120 bytes (1953 MiB, 3970 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs) [ 21.545231] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 21.551961] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID B68B723A-8996-4F3B-90B4-085F569C440A, small LPT model [ 21.744808] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 21.752114] block: unable to load configuration (fstab: Entry not found) [ 21.759013] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 21.765779] block: unable to load configuration (fstab: Entry not found) [ 21.772834] block: attempting to load /etc/config/fstab [ 21.778288] block: unable to load configuration (fstab: Entry not found) [ 21.785228] block: no usable configuration [ 21.791256] mount_root: overlay filesystem has not been fully initialized yet [ 21.799046] mount_root: switching to ubifs overlay [ 21.861249] urandom-seed: Seed file not found (/etc/urandom.seed) [ 21.920065] procd: - early - [ 21.923896] procd: - watchdog - [ 22.659390] procd: - watchdog - [ 22.663015] procd: - ubus - [ 23.107285] procd: - init - [ 24.213773] kmodloader: loading kernel modules from /etc/modules.d/* [ 24.249852] Loading modules backported from Linux version v4.19.32-0-g3a2156c839c7 [ 24.257599] Backport generated by backports.git v4.19.32-1-0-g1c4f7569 [ 24.414363] urngd: v1.0.0 started. [ 24.531865] ath9k ar934x_wmac: Direct firmware load for soc_wmac.eeprom failed with error -2 [ 24.540434] ath9k ar934x_wmac: Falling back to user helper [ 24.783701] ath: EEPROM regdomain: 0x0 [ 24.783711] ath: EEPROM indicates default country code should be used [ 24.783715] ath: doing EEPROM country->regdmn map search [ 24.783732] ath: country maps to regdmn code: 0x3a [ 24.783738] ath: Country alpha2 being used: US [ 24.783742] ath: Regpair used: 0x3a [ 24.798126] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 24.800212] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47 [ 24.807211] pci 0000:00:00.0: using irq 40 for pin 1 [ 24.812316] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 24.819265] ath9k 0000:00:00.0: Direct firmware load for pci_wmac0.eeprom failed with error -2 [ 24.828062] ath9k 0000:00:00.0: Falling back to user helper [ 26.012946] ath: EEPROM regdomain: 0x0 [ 26.012955] ath: EEPROM indicates default country code should be used [ 26.012959] ath: doing EEPROM country->regdmn map search [ 26.012976] ath: country maps to regdmn code: 0x3a [ 26.012982] ath: Country alpha2 being used: US [ 26.012986] ath: Regpair used: 0x3a [ 26.024432] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 26.026552] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40 [ 26.067936] usbcore: registered new interface driver ath9k_htc [ 26.122920] RPC: Registered named UNIX socket transport module. [ 26.128935] RPC: Registered udp transport module. [ 26.133758] RPC: Registered tcp transport module. [ 26.138525] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 26.229459] usbcore: registered new interface driver mt76x2u [ 26.298803] usbcore: registered new interface driver rt2800usb [ 26.320018] usbcore: registered new interface driver rtl8187 [ 26.388766] usbcore: registered new interface driver rtl8192cu [ 26.473917] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 26.528195] usbcore: registered new interface driver cdc_acm [ 26.534002] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 26.572450] usbcore: registered new interface driver cdc_wdm [ 26.593939] ip_tables: (C) 2000-2006 Netfilter Core Team [ 26.621914] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 26.817434] usbcore: registered new interface driver ums-alauda [ 26.845121] usbcore: registered new interface driver ums-cypress [ 26.863855] usbcore: registered new interface driver ums-datafab [ 26.878724] usbcore: registered new interface driver ums-freecom [ 26.903798] usbcore: registered new interface driver ums-isd200 [ 26.914248] usbcore: registered new interface driver ums-jumpshot [ 26.931971] usbcore: registered new interface driver ums-karma [ 26.948489] usbcore: registered new interface driver ums-sddr09 [ 26.957478] usbcore: registered new interface driver ums-sddr55 [ 26.966776] usbcore: registered new interface driver ums-usbat [ 26.988301] usbcore: registered new interface driver usbserial [ 26.994403] usbcore: registered new interface driver usbserial_generic [ 27.001117] usbserial: USB Serial support registered for generic [ 27.029159] xt_time: kernel timezone is -0000 [ 27.037759] usbcore: registered new interface driver asix [ 27.046917] usbcore: registered new interface driver ax88179_178a [ 27.056794] usbcore: registered new interface driver cdc_ether [ 27.073297] usbcore: registered new interface driver pl2303 [ 27.079070] usbserial: USB Serial support registered for pl2303 [ 27.090336] PPP generic driver version 2.4.2 [ 27.097929] NET: Registered protocol family 24 [ 27.106127] usbcore: registered new interface driver rndis_host [ 27.117029] kmodloader: done loading kernel modules from /etc/modules.d/* [ 39.936226] br-lan: port 1(eth1) entered blocking state [ 39.941545] br-lan: port 1(eth1) entered disabled state [ 39.947229] device eth1 entered promiscuous mode [ 39.964280] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 40.176725] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 42.061418] eth1: link up (100Mbps/Full duplex) [ 42.083662] br-lan: port 1(eth1) entered blocking state [ 42.088987] br-lan: port 1(eth1) entered forwarding state [ 42.171519] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 69.247854] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 70.602949] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 70.630171] br-lan: port 2(wlan0) entered blocking state [ 70.635635] br-lan: port 2(wlan0) entered disabled state [ 70.641348] device wlan0 entered promiscuous mode [ 70.701450] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 70.708184] br-lan: port 2(wlan0) entered blocking state [ 70.713637] br-lan: port 2(wlan0) entered forwarding state [ 80.173898] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 83.385964] device wlan0 left promiscuous mode [ 83.390722] br-lan: port 2(wlan0) entered disabled state [ 84.113490] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 84.176750] br-lan: port 2(wlan0) entered blocking state [ 84.182211] br-lan: port 2(wlan0) entered disabled state [ 84.188014] device wlan0 entered promiscuous mode [ 84.192963] br-lan: port 2(wlan0) entered blocking state [ 84.198362] br-lan: port 2(wlan0) entered forwarding state [ 84.262022] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 88.726890] br-lan: port 2(wlan0) entered disabled state [ 89.103998] device wlan0 left promiscuous mode [ 89.108627] br-lan: port 2(wlan0) entered disabled state [ 159.949699] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 160.426744] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 160.437223] br-lan: port 2(wlan0) entered blocking state [ 160.442692] br-lan: port 2(wlan0) entered disabled state [ 160.448504] device wlan0 entered promiscuous mode [ 160.453460] br-lan: port 2(wlan0) entered blocking state [ 160.458885] br-lan: port 2(wlan0) entered forwarding state [ 160.488240] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 160.502101] br-lan: port 3(wlan0-1) entered blocking state [ 160.507820] br-lan: port 3(wlan0-1) entered disabled state [ 160.513849] device wlan0-1 entered promiscuous mode [ 160.532051] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready [ 160.538391] br-lan: port 3(wlan0-1) entered blocking state [ 160.544021] br-lan: port 3(wlan0-1) entered forwarding state [ 160.961690] br-lan: port 3(wlan0-1) entered disabled state [ 161.090438] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready [ 161.097307] br-lan: port 3(wlan0-1) entered blocking state [ 161.102934] br-lan: port 3(wlan0-1) entered forwarding state [ 448.431652] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 448.654897] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 449.064964] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 449.316052] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 449.581735] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 449.587355] ath9k_htc 1-1:1.0: FW RMW support: On [ 449.592236] ath: EEPROM regdomain: 0x833a [ 449.592241] ath: EEPROM indicates we should expect a country code [ 449.592257] ath: doing EEPROM country->regdmn map search [ 449.592265] ath: country maps to regdmn code: 0x37 [ 449.592271] ath: Country alpha2 being used: GB [ 449.592276] ath: Regpair used: 0x37 [ 449.621376] ieee80211 phy2: Atheros AR9271 Rev:1 [ 461.402618] eth1: link down [ 461.406347] br-lan: port 1(eth1) entered disabled state [ 462.443862] eth1: link up (100Mbps/Full duplex) [ 462.448513] br-lan: port 1(eth1) entered blocking state [ 462.453871] br-lan: port 1(eth1) entered forwarding state [ 648.021678] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 755.357813] device wlan0 left promiscuous mode [ 755.362589] br-lan: port 2(wlan0) entered disabled state [ 755.392726] device wlan0-1 left promiscuous mode [ 755.397571] br-lan: port 3(wlan0-1) entered disabled state [ 757.708484] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 757.952464] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 758.527049] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 758.625778] br-lan: port 2(wlan0) entered blocking state [ 758.631183] br-lan: port 2(wlan0) entered disabled state [ 758.637014] device wlan0 entered promiscuous mode [ 758.641986] br-lan: port 2(wlan0) entered blocking state [ 758.647402] br-lan: port 2(wlan0) entered forwarding state [ 758.755889] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 759.292222] usb 1-1: USB disconnect, device number 2 [ 759.404222] ath: phy2: RX failed to go idle in 10 ms RXSM=0x2000000 [ 759.512805] ath: phy2: RX failed to go idle in 10 ms RXSM=0x2000000 [ 759.622708] ath: phy2: RX failed to go idle in 10 ms RXSM=0x2000000 [ 759.641237] usb 1-1: ath9k_htc: USB layer deinitialized [ 760.031725] usb 1-1: new high-speed USB device number 3 using ehci-platform [ 760.254554] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 760.563322] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 760.814301] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 761.089959] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 761.095630] ath9k_htc 1-1:1.0: FW RMW support: On [ 761.100433] ath: EEPROM regdomain: 0x833a [ 761.100438] ath: EEPROM indicates we should expect a country code [ 761.100453] ath: doing EEPROM country->regdmn map search [ 761.100461] ath: country maps to regdmn code: 0x37 [ 761.100468] ath: Country alpha2 being used: GB [ 761.100472] ath: Regpair used: 0x37 [ 761.154213] ieee80211 phy3: Atheros AR9271 Rev:1 [ 761.351301] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 761.662269] usb 1-1: USB disconnect, device number 3 [ 761.782846] ath: phy3: RX failed to go idle in 10 ms RXSM=0x2000000 [ 761.891334] ath: phy3: RX failed to go idle in 10 ms RXSM=0x2000000 [ 762.000935] ath: phy3: RX failed to go idle in 10 ms RXSM=0x2000000 [ 762.867803] usb 1-1: ath9k_htc: USB layer deinitialized [ 763.271742] usb 1-1: new high-speed USB device number 4 using ehci-platform [ 763.494517] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 763.800559] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 764.052353] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 764.367587] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 764.373241] ath9k_htc 1-1:1.0: FW RMW support: On [ 764.378048] ath: EEPROM regdomain: 0x833a [ 764.378052] ath: EEPROM indicates we should expect a country code [ 764.378068] ath: doing EEPROM country->regdmn map search [ 764.378076] ath: country maps to regdmn code: 0x37 [ 764.378082] ath: Country alpha2 being used: GB [ 764.378087] ath: Regpair used: 0x37 [ 764.446324] ieee80211 phy4: Atheros AR9271 Rev:1 [ 764.937418] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 766.403534] usb 1-1: USB disconnect, device number 4 [ 766.524427] ath: phy4: RX failed to go idle in 10 ms RXSM=0x2000000 [ 766.632985] ath: phy4: RX failed to go idle in 10 ms RXSM=0x2000000 [ 766.742971] ath: phy4: RX failed to go idle in 10 ms RXSM=0x2000000 [ 767.352420] usb 1-1: ath9k_htc: USB layer deinitialized [ 767.731694] usb 1-1: new high-speed USB device number 5 using ehci-platform [ 767.954452] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 768.253061] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 768.504621] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 768.782937] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 768.788609] ath9k_htc 1-1:1.0: FW RMW support: On [ 768.793462] ath: EEPROM regdomain: 0x833a [ 768.793466] ath: EEPROM indicates we should expect a country code [ 768.793483] ath: doing EEPROM country->regdmn map search [ 768.793490] ath: country maps to regdmn code: 0x37 [ 768.793497] ath: Country alpha2 being used: GB [ 768.793501] ath: Regpair used: 0x37 [ 768.857542] ieee80211 phy5: Atheros AR9271 Rev:1 [ 772.373500] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 774.252244] usb 1-1: USB disconnect, device number 5 [ 774.365340] ath: phy5: RX failed to go idle in 10 ms RXSM=0x2000000 [ 774.473560] ath: phy5: RX failed to go idle in 10 ms RXSM=0x2000000 [ 774.583614] ath: phy5: RX failed to go idle in 10 ms RXSM=0x2000000 [ 774.742242] usb 1-1: ath9k_htc: USB layer deinitialized [ 775.091715] usb 1-1: new high-speed USB device number 6 using ehci-platform [ 775.314879] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 775.613441] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 775.864804] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 776.133940] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 776.139610] ath9k_htc 1-1:1.0: FW RMW support: On [ 776.144434] ath: EEPROM regdomain: 0x833a [ 776.144438] ath: EEPROM indicates we should expect a country code [ 776.144454] ath: doing EEPROM country->regdmn map search [ 776.144462] ath: country maps to regdmn code: 0x37 [ 776.144468] ath: Country alpha2 being used: GB [ 776.144473] ath: Regpair used: 0x37 [ 776.159829] ieee80211 phy6: Atheros AR9271 Rev:1 [ 776.347890] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 776.669659] usb 1-1: USB disconnect, device number 6 [ 776.781966] ath: phy6: RX failed to go idle in 10 ms RXSM=0x2000000 [ 776.890147] ath: phy6: RX failed to go idle in 10 ms RXSM=0x2000000 [ 776.999768] ath: phy6: RX failed to go idle in 10 ms RXSM=0x2000000 [ 777.582284] usb 1-1: ath9k_htc: USB layer deinitialized [ 777.951701] usb 1-1: new high-speed USB device number 7 using ehci-platform [ 778.185255] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 778.492688] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 778.743687] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 779.018938] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 779.024709] ath9k_htc 1-1:1.0: FW RMW support: On [ 779.029505] ath: EEPROM regdomain: 0x833a [ 779.029509] ath: EEPROM indicates we should expect a country code [ 779.029526] ath: doing EEPROM country->regdmn map search [ 779.029533] ath: country maps to regdmn code: 0x37 [ 779.029540] ath: Country alpha2 being used: GB [ 779.029544] ath: Regpair used: 0x37 [ 779.048935] ieee80211 phy7: Atheros AR9271 Rev:1 [ 782.798542] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 784.602287] usb 1-1: USB disconnect, device number 7 [ 784.714080] ath: phy7: RX failed to go idle in 10 ms RXSM=0x2000000 [ 784.822292] ath: phy7: RX failed to go idle in 10 ms RXSM=0x2000000 [ 784.932263] ath: phy7: RX failed to go idle in 10 ms RXSM=0x2000000 [ 785.342190] usb 1-1: ath9k_htc: USB layer deinitialized [ 785.721709] usb 1-1: new high-speed USB device number 8 using ehci-platform [ 785.954509] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 786.268615] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 786.513806] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 786.796190] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 786.801878] ath9k_htc 1-1:1.0: FW RMW support: On [ 786.806760] ath: EEPROM regdomain: 0x833a [ 786.806765] ath: EEPROM indicates we should expect a country code [ 786.806782] ath: doing EEPROM country->regdmn map search [ 786.806789] ath: country maps to regdmn code: 0x37 [ 786.806796] ath: Country alpha2 being used: GB [ 786.806800] ath: Regpair used: 0x37 [ 786.837309] ieee80211 phy8: Atheros AR9271 Rev:1 [ 787.012591] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 787.332252] usb 1-1: USB disconnect, device number 8 [ 787.448103] ath: phy8: RX failed to go idle in 10 ms RXSM=0x2000000 [ 787.556677] ath: phy8: RX failed to go idle in 10 ms RXSM=0x2000000 [ 787.666630] ath: phy8: RX failed to go idle in 10 ms RXSM=0x2000000 [ 788.432416] usb 1-1: ath9k_htc: USB layer deinitialized [ 788.831765] usb 1-1: new high-speed USB device number 9 using ehci-platform [ 789.057708] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 789.366971] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 789.618184] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 789.898314] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 789.904080] ath9k_htc 1-1:1.0: FW RMW support: On [ 789.908935] ath: EEPROM regdomain: 0x833a [ 789.908940] ath: EEPROM indicates we should expect a country code [ 789.908957] ath: doing EEPROM country->regdmn map search [ 789.908964] ath: country maps to regdmn code: 0x37 [ 789.908971] ath: Country alpha2 being used: GB [ 789.908975] ath: Regpair used: 0x37 [ 789.954953] ieee80211 phy9: Atheros AR9271 Rev:1 [ 790.373976] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 791.692241] usb 1-1: USB disconnect, device number 9 [ 791.813808] ath: phy9: RX failed to go idle in 10 ms RXSM=0x2000000 [ 791.921967] ath: phy9: RX failed to go idle in 10 ms RXSM=0x2000000 [ 792.031639] ath: phy9: RX failed to go idle in 10 ms RXSM=0x2000000 [ 792.842128] usb 1-1: ath9k_htc: USB layer deinitialized [ 793.191741] usb 1-1: new high-speed USB device number 10 using ehci-platform [ 793.424783] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 793.751942] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 793.998688] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 794.303048] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 794.308845] ath9k_htc 1-1:1.0: FW RMW support: On [ 794.313685] ath: EEPROM regdomain: 0x833a [ 794.313689] ath: EEPROM indicates we should expect a country code [ 794.313705] ath: doing EEPROM country->regdmn map search [ 794.313712] ath: country maps to regdmn code: 0x37 [ 794.313719] ath: Country alpha2 being used: GB [ 794.313723] ath: Regpair used: 0x37 [ 794.337310] ieee80211 phy10: Atheros AR9271 Rev:1 [ 794.528916] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 794.832242] usb 1-1: USB disconnect, device number 10 [ 794.948575] ath: phy10: RX failed to go idle in 10 ms RXSM=0x2000000 [ 795.057205] ath: phy10: RX failed to go idle in 10 ms RXSM=0x2000000 [ 795.171018] ath: phy10: RX failed to go idle in 10 ms RXSM=0x2000000 [ 795.882107] usb 1-1: ath9k_htc: USB layer deinitialized [ 796.261723] usb 1-1: new high-speed USB device number 11 using ehci-platform [ 796.484498] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 796.792198] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 797.043353] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 797.306048] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 797.311826] ath9k_htc 1-1:1.0: FW RMW support: On [ 797.316618] ath: EEPROM regdomain: 0x833a [ 797.316622] ath: EEPROM indicates we should expect a country code [ 797.316638] ath: doing EEPROM country->regdmn map search [ 797.316646] ath: country maps to regdmn code: 0x37 [ 797.316652] ath: Country alpha2 being used: GB [ 797.316657] ath: Regpair used: 0x37 [ 797.332237] ieee80211 phy11: Atheros AR9271 Rev:1 [ 798.753350] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 800.274854] usb 1-1: USB disconnect, device number 11 [ 800.401919] ath: phy11: RX failed to go idle in 10 ms RXSM=0x2000000 [ 800.510365] ath: phy11: RX failed to go idle in 10 ms RXSM=0x2000000 [ 800.620695] ath: phy11: RX failed to go idle in 10 ms RXSM=0x2000000 [ 801.152092] usb 1-1: ath9k_htc: USB layer deinitialized [ 801.531696] usb 1-1: new high-speed USB device number 12 using ehci-platform [ 801.764890] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 802.070463] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 802.321421] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 802.612333] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 802.617963] ath9k_htc 1-1:1.0: FW RMW support: On [ 802.622811] ath: EEPROM regdomain: 0x833a [ 802.622816] ath: EEPROM indicates we should expect a country code [ 802.622832] ath: doing EEPROM country->regdmn map search [ 802.622839] ath: country maps to regdmn code: 0x37 [ 802.622846] ath: Country alpha2 being used: GB [ 802.622850] ath: Regpair used: 0x37 [ 802.656238] ieee80211 phy12: Atheros AR9271 Rev:1 [ 805.965388] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 807.432258] usb 1-1: USB disconnect, device number 12 [ 807.549502] ath: phy12: RX failed to go idle in 10 ms RXSM=0x2000000 [ 807.658504] ath: phy12: RX failed to go idle in 10 ms RXSM=0x2000000 [ 807.768603] ath: phy12: RX failed to go idle in 10 ms RXSM=0x2000000 [ 808.182201] usb 1-1: ath9k_htc: USB layer deinitialized [ 808.551711] usb 1-1: new high-speed USB device number 13 using ehci-platform [ 808.774521] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 809.092320] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 809.343308] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 809.632440] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 809.638093] ath9k_htc 1-1:1.0: FW RMW support: On [ 809.642918] ath: EEPROM regdomain: 0x833a [ 809.642922] ath: EEPROM indicates we should expect a country code [ 809.642938] ath: doing EEPROM country->regdmn map search [ 809.642946] ath: country maps to regdmn code: 0x37 [ 809.642952] ath: Country alpha2 being used: GB [ 809.642957] ath: Regpair used: 0x37 [ 809.676318] ieee80211 phy13: Atheros AR9271 Rev:1 [ 809.860260] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 810.182693] usb 1-1: USB disconnect, device number 13 [ 810.315245] ath: phy13: RX failed to go idle in 10 ms RXSM=0x2000000 [ 810.423828] ath: phy13: RX failed to go idle in 10 ms RXSM=0x2000000 [ 810.533785] ath: phy13: RX failed to go idle in 10 ms RXSM=0x2000000 [ 811.402189] usb 1-1: ath9k_htc: USB layer deinitialized [ 811.791844] usb 1-1: new high-speed USB device number 14 using ehci-platform [ 812.054659] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 812.368694] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 812.619930] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 812.902690] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 812.908320] ath9k_htc 1-1:1.0: FW RMW support: On [ 812.913169] ath: EEPROM regdomain: 0x833a [ 812.913174] ath: EEPROM indicates we should expect a country code [ 812.913190] ath: doing EEPROM country->regdmn map search [ 812.913198] ath: country maps to regdmn code: 0x37 [ 812.913205] ath: Country alpha2 being used: GB [ 812.913209] ath: Regpair used: 0x37 [ 812.947317] ieee80211 phy14: Atheros AR9271 Rev:1 [ 813.433387] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 814.752245] usb 1-1: USB disconnect, device number 14 [ 814.870284] ath: phy14: RX failed to go idle in 10 ms RXSM=0x2000000 [ 814.978558] ath: phy14: RX failed to go idle in 10 ms RXSM=0x2000000 [ 815.088283] ath: phy14: RX failed to go idle in 10 ms RXSM=0x2000000 [ 815.692245] usb 1-1: ath9k_htc: USB layer deinitialized [ 816.061681] usb 1-1: new high-speed USB device number 15 using ehci-platform [ 816.284461] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 816.593362] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 816.844935] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 817.120303] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 817.125996] ath9k_htc 1-1:1.0: FW RMW support: On [ 817.130778] ath: EEPROM regdomain: 0x833a [ 817.130782] ath: EEPROM indicates we should expect a country code [ 817.130799] ath: doing EEPROM country->regdmn map search [ 817.130806] ath: country maps to regdmn code: 0x37 [ 817.130812] ath: Country alpha2 being used: GB [ 817.130817] ath: Regpair used: 0x37 [ 817.167710] ieee80211 phy15: Atheros AR9271 Rev:1 [ 820.706756] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 822.482226] usb 1-1: USB disconnect, device number 15 [ 822.605422] ath: phy15: RX failed to go idle in 10 ms RXSM=0x2000000 [ 822.714639] ath: phy15: RX failed to go idle in 10 ms RXSM=0x2000000 [ 822.824792] ath: phy15: RX failed to go idle in 10 ms RXSM=0x2000000 [ 823.222418] usb 1-1: ath9k_htc: USB layer deinitialized [ 823.612370] usb 1-1: new high-speed USB device number 16 using ehci-platform [ 823.835039] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 824.153818] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 824.404666] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 824.673048] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 824.678701] ath9k_htc 1-1:1.0: FW RMW support: On [ 824.683524] ath: EEPROM regdomain: 0x833a [ 824.683529] ath: EEPROM indicates we should expect a country code [ 824.683544] ath: doing EEPROM country->regdmn map search [ 824.683552] ath: country maps to regdmn code: 0x37 [ 824.683558] ath: Country alpha2 being used: GB [ 824.683563] ath: Regpair used: 0x37 [ 824.716937] ieee80211 phy16: Atheros AR9271 Rev:1 [ 824.909318] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 825.232425] usb 1-1: USB disconnect, device number 16 [ 825.355735] ath: phy16: RX failed to go idle in 10 ms RXSM=0x2000000 [ 825.464396] ath: phy16: RX failed to go idle in 10 ms RXSM=0x2000000 [ 825.574549] ath: phy16: RX failed to go idle in 10 ms RXSM=0x2000000 [ 826.282421] usb 1-1: ath9k_htc: USB layer deinitialized [ 826.671781] usb 1-1: new high-speed USB device number 17 using ehci-platform [ 826.894610] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 827.198323] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 827.449196] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 827.764303] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 827.769946] ath9k_htc 1-1:1.0: FW RMW support: On [ 827.774892] ath: EEPROM regdomain: 0x833a [ 827.774897] ath: EEPROM indicates we should expect a country code [ 827.774913] ath: doing EEPROM country->regdmn map search [ 827.774921] ath: country maps to regdmn code: 0x37 [ 827.774927] ath: Country alpha2 being used: GB [ 827.774932] ath: Regpair used: 0x37 [ 827.807403] ieee80211 phy17: Atheros AR9271 Rev:1 [ 828.178701] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 829.482250] usb 1-1: USB disconnect, device number 17 [ 829.608323] ath: phy17: RX failed to go idle in 10 ms RXSM=0x2000000 [ 829.716647] ath: phy17: RX failed to go idle in 10 ms RXSM=0x2000000 [ 829.826823] ath: phy17: RX failed to go idle in 10 ms RXSM=0x2000000 [ 830.622076] usb 1-1: ath9k_htc: USB layer deinitialized [ 831.001814] usb 1-1: new high-speed USB device number 18 using ehci-platform [ 831.234694] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 831.548577] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 831.800072] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 832.068441] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 832.074124] ath9k_htc 1-1:1.0: FW RMW support: On [ 832.078912] ath: EEPROM regdomain: 0x833a [ 832.078917] ath: EEPROM indicates we should expect a country code [ 832.078933] ath: doing EEPROM country->regdmn map search [ 832.078941] ath: country maps to regdmn code: 0x37 [ 832.078948] ath: Country alpha2 being used: GB [ 832.078952] ath: Regpair used: 0x37 [ 832.096810] ieee80211 phy18: Atheros AR9271 Rev:1 [ 832.283067] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 832.602239] usb 1-1: USB disconnect, device number 18 [ 832.718533] ath: phy18: RX failed to go idle in 10 ms RXSM=0x2000000 [ 832.826745] ath: phy18: RX failed to go idle in 10 ms RXSM=0x2000000 [ 832.936637] ath: phy18: RX failed to go idle in 10 ms RXSM=0x2000000 [ 833.602751] usb 1-1: ath9k_htc: USB layer deinitialized [ 833.981743] usb 1-1: new high-speed USB device number 19 using ehci-platform [ 834.214497] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 834.524560] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 834.775434] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 835.035175] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 835.040804] ath9k_htc 1-1:1.0: FW RMW support: On [ 835.045645] ath: EEPROM regdomain: 0x833a [ 835.045650] ath: EEPROM indicates we should expect a country code [ 835.045666] ath: doing EEPROM country->regdmn map search [ 835.045674] ath: country maps to regdmn code: 0x37 [ 835.045680] ath: Country alpha2 being used: GB [ 835.045685] ath: Regpair used: 0x37 [ 835.085026] ieee80211 phy19: Atheros AR9271 Rev:1 [ 836.449500] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 837.912244] usb 1-1: USB disconnect, device number 19 [ 838.028322] ath: phy19: RX failed to go idle in 10 ms RXSM=0x2000000 [ 838.140767] ath: phy19: RX failed to go idle in 10 ms RXSM=0x2000000 [ 838.250536] ath: phy19: RX failed to go idle in 10 ms RXSM=0x2000000 [ 838.832092] usb 1-1: ath9k_htc: USB layer deinitialized [ 839.221695] usb 1-1: new high-speed USB device number 20 using ehci-platform [ 839.444641] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 839.768061] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 840.018932] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 840.305792] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 840.311425] ath9k_htc 1-1:1.0: FW RMW support: On [ 840.316250] ath: EEPROM regdomain: 0x833a [ 840.316255] ath: EEPROM indicates we should expect a country code [ 840.316271] ath: doing EEPROM country->regdmn map search [ 840.316278] ath: country maps to regdmn code: 0x37 [ 840.316285] ath: Country alpha2 being used: GB [ 840.316289] ath: Regpair used: 0x37 [ 840.339407] ieee80211 phy20: Atheros AR9271 Rev:1 [ 843.622957] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 845.112232] usb 1-1: USB disconnect, device number 20 [ 845.228294] ath: phy20: RX failed to go idle in 10 ms RXSM=0x2000000 [ 845.336800] ath: phy20: RX failed to go idle in 10 ms RXSM=0x2000000 [ 845.446817] ath: phy20: RX failed to go idle in 10 ms RXSM=0x2000000 [ 845.862219] usb 1-1: ath9k_htc: USB layer deinitialized [ 846.241701] usb 1-1: new high-speed USB device number 21 using ehci-platform [ 846.464790] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 846.783694] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 847.034561] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 847.309848] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 847.315559] ath9k_htc 1-1:1.0: FW RMW support: On [ 847.320351] ath: EEPROM regdomain: 0x833a [ 847.320355] ath: EEPROM indicates we should expect a country code [ 847.320372] ath: doing EEPROM country->regdmn map search [ 847.320379] ath: country maps to regdmn code: 0x37 [ 847.320386] ath: Country alpha2 being used: GB [ 847.320390] ath: Regpair used: 0x37 [ 847.350500] ieee80211 phy21: Atheros AR9271 Rev:1 [ 847.511826] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 847.835307] usb 1-1: USB disconnect, device number 21 [ 847.950542] ath: phy21: RX failed to go idle in 10 ms RXSM=0x2000000 [ 848.059114] ath: phy21: RX failed to go idle in 10 ms RXSM=0x2000000 [ 848.172485] ath: phy21: RX failed to go idle in 10 ms RXSM=0x2000000 [ 849.038389] usb 1-1: ath9k_htc: USB layer deinitialized [ 849.431713] usb 1-1: new high-speed USB device number 22 using ehci-platform [ 849.695637] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 850.034351] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 850.285148] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 850.555937] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 850.561721] ath9k_htc 1-1:1.0: FW RMW support: On [ 850.566521] ath: EEPROM regdomain: 0x833a [ 850.566525] ath: EEPROM indicates we should expect a country code [ 850.566541] ath: doing EEPROM country->regdmn map search [ 850.566548] ath: country maps to regdmn code: 0x37 [ 850.566555] ath: Country alpha2 being used: GB [ 850.566560] ath: Regpair used: 0x37 [ 850.603416] ieee80211 phy22: Atheros AR9271 Rev:1 [ 851.010630] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 852.392231] usb 1-1: USB disconnect, device number 22 [ 852.518786] ath: phy22: RX failed to go idle in 10 ms RXSM=0x2000000 [ 852.627084] ath: phy22: RX failed to go idle in 10 ms RXSM=0x2000000 [ 852.736755] ath: phy22: RX failed to go idle in 10 ms RXSM=0x2000000 [ 853.322250] usb 1-1: ath9k_htc: USB layer deinitialized [ 853.691697] usb 1-1: new high-speed USB device number 23 using ehci-platform [ 853.914752] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 854.313610] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 854.564418] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 854.850300] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 854.855962] ath9k_htc 1-1:1.0: FW RMW support: On [ 854.860857] ath: EEPROM regdomain: 0x833a [ 854.860862] ath: EEPROM indicates we should expect a country code [ 854.860879] ath: doing EEPROM country->regdmn map search [ 854.860886] ath: country maps to regdmn code: 0x37 [ 854.860893] ath: Country alpha2 being used: GB [ 854.860897] ath: Regpair used: 0x37 [ 854.938445] ieee80211 phy23: Atheros AR9271 Rev:1 [ 856.154110] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 857.642409] usb 1-1: USB disconnect, device number 23 [ 857.762998] ath: phy23: RX failed to go idle in 10 ms RXSM=0x2000000 [ 857.871183] ath: phy23: RX failed to go idle in 10 ms RXSM=0x2000000 [ 857.980920] ath: phy23: RX failed to go idle in 10 ms RXSM=0x2000000 [ 858.462123] usb 1-1: ath9k_htc: USB layer deinitialized [ 858.841697] usb 1-1: new high-speed USB device number 24 using ehci-platform [ 859.074592] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 859.402659] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 859.655596] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 859.946176] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 859.951846] ath9k_htc 1-1:1.0: FW RMW support: On [ 859.956652] ath: EEPROM regdomain: 0x833a [ 859.956656] ath: EEPROM indicates we should expect a country code [ 859.956673] ath: doing EEPROM country->regdmn map search [ 859.956681] ath: country maps to regdmn code: 0x37 [ 859.956687] ath: Country alpha2 being used: GB [ 859.956691] ath: Regpair used: 0x37 [ 859.996403] ieee80211 phy24: Atheros AR9271 Rev:1 [ 863.405438] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 864.872829] usb 1-1: USB disconnect, device number 24 [ 864.998341] ath: phy24: RX failed to go idle in 10 ms RXSM=0x2000000 [ 865.110188] ath: phy24: RX failed to go idle in 10 ms RXSM=0x2000000 [ 865.219951] ath: phy24: RX failed to go idle in 10 ms RXSM=0x2000000 [ 865.652202] usb 1-1: ath9k_htc: USB layer deinitialized [ 866.011707] usb 1-1: new high-speed USB device number 25 using ehci-platform [ 866.234990] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 866.565431] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 866.816429] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 867.073090] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 867.078582] ath9k_htc 1-1:1.0: FW RMW support: On [ 867.087316] ath: EEPROM regdomain: 0x833a [ 867.087322] ath: EEPROM indicates we should expect a country code [ 867.087339] ath: doing EEPROM country->regdmn map search [ 867.087346] ath: country maps to regdmn code: 0x37 [ 867.087353] ath: Country alpha2 being used: GB [ 867.087357] ath: Regpair used: 0x37 [ 867.128812] ieee80211 phy25: Atheros AR9271 Rev:1 [ 867.312482] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 869.213254] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 870.962217] usb 1-1: USB disconnect, device number 25 [ 871.081825] ath: phy25: RX failed to go idle in 10 ms RXSM=0x2000000 [ 871.193788] ath: phy25: RX failed to go idle in 10 ms RXSM=0x2000000 [ 871.303527] ath: phy25: RX failed to go idle in 10 ms RXSM=0x2000000 [ 871.793787] usb 1-1: ath9k_htc: USB layer deinitialized [ 872.181691] usb 1-1: new high-speed USB device number 26 using ehci-platform [ 872.424997] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 872.753179] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 873.004328] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 873.270816] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 873.276474] ath9k_htc 1-1:1.0: FW RMW support: On [ 873.281276] ath: EEPROM regdomain: 0x833a [ 873.281280] ath: EEPROM indicates we should expect a country code [ 873.281297] ath: doing EEPROM country->regdmn map search [ 873.281305] ath: country maps to regdmn code: 0x37 [ 873.281312] ath: Country alpha2 being used: GB [ 873.281316] ath: Regpair used: 0x37 [ 873.296938] ieee80211 phy26: Atheros AR9271 Rev:1 [ 875.998175] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 877.772255] usb 1-1: USB disconnect, device number 26 [ 877.890647] ath: phy26: RX failed to go idle in 10 ms RXSM=0x2000000 [ 877.999106] ath: phy26: RX failed to go idle in 10 ms RXSM=0x2000000 [ 878.109221] ath: phy26: RX failed to go idle in 10 ms RXSM=0x2000000 [ 878.562740] usb 1-1: ath9k_htc: USB layer deinitialized [ 878.961707] usb 1-1: new high-speed USB device number 27 using ehci-platform [ 879.185050] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 879.493441] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 879.744684] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 880.023049] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 880.028683] ath9k_htc 1-1:1.0: FW RMW support: On [ 880.033504] ath: EEPROM regdomain: 0x833a [ 880.033509] ath: EEPROM indicates we should expect a country code [ 880.033525] ath: doing EEPROM country->regdmn map search [ 880.033533] ath: country maps to regdmn code: 0x37 [ 880.033539] ath: Country alpha2 being used: GB [ 880.033544] ath: Regpair used: 0x37 [ 880.070732] ieee80211 phy27: Atheros AR9271 Rev:1 [ 883.481527] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 884.912270] usb 1-1: USB disconnect, device number 27 [ 885.034970] ath: phy27: RX failed to go idle in 10 ms RXSM=0x2000000 [ 885.146946] ath: phy27: RX failed to go idle in 10 ms RXSM=0x2000000 [ 885.256892] ath: phy27: RX failed to go idle in 10 ms RXSM=0x2000000 [ 885.802203] usb 1-1: ath9k_htc: USB layer deinitialized [ 886.171731] usb 1-1: new high-speed USB device number 28 using ehci-platform [ 886.414488] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 886.718556] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 886.969437] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 887.244937] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 887.250567] ath9k_htc 1-1:1.0: FW RMW support: On [ 887.255410] ath: EEPROM regdomain: 0x833a [ 887.255415] ath: EEPROM indicates we should expect a country code [ 887.255431] ath: doing EEPROM country->regdmn map search [ 887.255439] ath: country maps to regdmn code: 0x37 [ 887.255445] ath: Country alpha2 being used: GB [ 887.255450] ath: Regpair used: 0x37 [ 887.276819] ieee80211 phy28: Atheros AR9271 Rev:1 [ 887.457266] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 887.772241] usb 1-1: USB disconnect, device number 28 [ 887.908168] ath: phy28: RX failed to go idle in 10 ms RXSM=0x2000000 [ 888.016617] ath: phy28: RX failed to go idle in 10 ms RXSM=0x2000000 [ 888.130085] ath: phy28: RX failed to go idle in 10 ms RXSM=0x2000000 [ 888.832232] usb 1-1: ath9k_htc: USB layer deinitialized [ 889.201756] usb 1-1: new high-speed USB device number 29 using ehci-platform [ 889.455732] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 889.753072] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 890.004428] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 890.321897] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 890.327443] ath9k_htc 1-1:1.0: FW RMW support: On [ 890.332501] ath: EEPROM regdomain: 0x833a [ 890.332507] ath: EEPROM indicates we should expect a country code [ 890.332523] ath: doing EEPROM country->regdmn map search [ 890.332530] ath: country maps to regdmn code: 0x37 [ 890.332537] ath: Country alpha2 being used: GB [ 890.332541] ath: Regpair used: 0x37 [ 890.386292] ieee80211 phy29: Atheros AR9271 Rev:1 [ 893.081067] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 894.462284] usb 1-1: USB disconnect, device number 29 [ 894.585233] ath: phy29: RX failed to go idle in 10 ms RXSM=0x2000000 [ 894.693638] ath: phy29: RX failed to go idle in 10 ms RXSM=0x2000000 [ 894.803333] ath: phy29: RX failed to go idle in 10 ms RXSM=0x2000000 [ 895.282194] usb 1-1: ath9k_htc: USB layer deinitialized [ 895.641739] usb 1-1: new high-speed USB device number 30 using ehci-platform [ 895.864648] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 896.181810] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 896.433469] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 896.687688] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 896.693380] ath9k_htc 1-1:1.0: FW RMW support: On [ 896.698160] ath: EEPROM regdomain: 0x833a [ 896.698164] ath: EEPROM indicates we should expect a country code [ 896.698181] ath: doing EEPROM country->regdmn map search [ 896.698188] ath: country maps to regdmn code: 0x37 [ 896.698195] ath: Country alpha2 being used: GB [ 896.698199] ath: Regpair used: 0x37 [ 896.726562] ieee80211 phy30: Atheros AR9271 Rev:1 [ 896.929367] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 899.044076] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 900.712242] usb 1-1: USB disconnect, device number 30 [ 900.827534] ath: phy30: RX failed to go idle in 10 ms RXSM=0x2000000 [ 900.935842] ath: phy30: RX failed to go idle in 10 ms RXSM=0x2000000 [ 901.045935] ath: phy30: RX failed to go idle in 10 ms RXSM=0x2000000 [ 901.460693] usb 1-1: ath9k_htc: USB layer deinitialized [ 901.841705] usb 1-1: new high-speed USB device number 31 using ehci-platform [ 902.074658] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 902.385690] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 902.644561] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 902.914929] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 902.920556] ath9k_htc 1-1:1.0: FW RMW support: On [ 902.925418] ath: EEPROM regdomain: 0x833a [ 902.925423] ath: EEPROM indicates we should expect a country code [ 902.925439] ath: doing EEPROM country->regdmn map search [ 902.925447] ath: country maps to regdmn code: 0x37 [ 902.925454] ath: Country alpha2 being used: GB [ 902.925458] ath: Regpair used: 0x37 [ 902.952143] ieee80211 phy31: Atheros AR9271 Rev:1 [ 903.149014] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 904.809423] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 906.306379] usb 1-1: USB disconnect, device number 31 [ 906.425253] ath: phy31: RX failed to go idle in 10 ms RXSM=0x2000000 [ 906.533660] ath: phy31: RX failed to go idle in 10 ms RXSM=0x2000000 [ 906.643455] ath: phy31: RX failed to go idle in 10 ms RXSM=0x2000000 [ 907.192159] usb 1-1: ath9k_htc: USB layer deinitialized [ 907.573294] usb 1-1: new high-speed USB device number 32 using ehci-platform [ 907.814991] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 908.142502] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 908.392807] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 908.663310] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 908.668946] ath9k_htc 1-1:1.0: FW RMW support: On [ 908.673798] ath: EEPROM regdomain: 0x833a [ 908.673804] ath: EEPROM indicates we should expect a country code [ 908.673820] ath: doing EEPROM country->regdmn map search [ 908.673828] ath: country maps to regdmn code: 0x37 [ 908.673834] ath: Country alpha2 being used: GB [ 908.673839] ath: Regpair used: 0x37 [ 908.690526] ieee80211 phy32: Atheros AR9271 Rev:1 [ 908.880509] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 909.212240] usb 1-1: USB disconnect, device number 32 [ 909.327283] ath: phy32: RX failed to go idle in 10 ms RXSM=0x2000000 [ 909.435527] ath: phy32: RX failed to go idle in 10 ms RXSM=0x2000000 [ 909.545313] ath: phy32: RX failed to go idle in 10 ms RXSM=0x2000000 [ 909.932427] usb 1-1: ath9k_htc: USB layer deinitialized [ 910.321705] usb 1-1: new high-speed USB device number 33 using ehci-platform [ 910.565751] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 910.881728] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 911.142807] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 911.425933] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 911.431561] ath9k_htc 1-1:1.0: FW RMW support: On [ 911.436404] ath: EEPROM regdomain: 0x833a [ 911.436408] ath: EEPROM indicates we should expect a country code [ 911.436424] ath: doing EEPROM country->regdmn map search [ 911.436432] ath: country maps to regdmn code: 0x37 [ 911.436438] ath: Country alpha2 being used: GB [ 911.436442] ath: Regpair used: 0x37 [ 911.465304] ieee80211 phy33: Atheros AR9271 Rev:1 [ 913.620565] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 915.122265] usb 1-1: USB disconnect, device number 33 [ 915.245498] ath: phy33: RX failed to go idle in 10 ms RXSM=0x2000000 [ 915.354142] ath: phy33: RX failed to go idle in 10 ms RXSM=0x2000000 [ 915.464112] ath: phy33: RX failed to go idle in 10 ms RXSM=0x2000000 [ 915.972085] usb 1-1: ath9k_htc: USB layer deinitialized [ 916.352857] usb 1-1: new high-speed USB device number 34 using ehci-platform [ 916.575103] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 916.912052] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 917.163321] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 917.470299] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 917.475997] ath9k_htc 1-1:1.0: FW RMW support: On [ 917.480777] ath: EEPROM regdomain: 0x833a [ 917.480781] ath: EEPROM indicates we should expect a country code [ 917.480798] ath: doing EEPROM country->regdmn map search [ 917.480805] ath: country maps to regdmn code: 0x37 [ 917.480812] ath: Country alpha2 being used: GB [ 917.480816] ath: Regpair used: 0x37 [ 917.506776] ieee80211 phy34: Atheros AR9271 Rev:1 [ 920.793052] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 922.132240] usb 1-1: USB disconnect, device number 34 [ 922.257961] ath: phy34: RX failed to go idle in 10 ms RXSM=0x2000000 [ 922.366283] ath: phy34: RX failed to go idle in 10 ms RXSM=0x2000000 [ 922.475887] ath: phy34: RX failed to go idle in 10 ms RXSM=0x2000000 [ 922.948207] usb 1-1: ath9k_htc: USB layer deinitialized [ 923.331740] usb 1-1: new high-speed USB device number 35 using ehci-platform [ 923.554907] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 923.872425] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 924.129053] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 924.392791] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 924.398556] ath9k_htc 1-1:1.0: FW RMW support: On [ 924.403439] ath: EEPROM regdomain: 0x833a [ 924.403444] ath: EEPROM indicates we should expect a country code [ 924.403460] ath: doing EEPROM country->regdmn map search [ 924.403468] ath: country maps to regdmn code: 0x37 [ 924.403475] ath: Country alpha2 being used: GB [ 924.403479] ath: Regpair used: 0x37 [ 924.424726] ieee80211 phy35: Atheros AR9271 Rev:1 [ 924.602329] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 924.922892] usb 1-1: USB disconnect, device number 35 [ 925.045504] ath: phy35: RX failed to go idle in 10 ms RXSM=0x2000000 [ 925.157365] ath: phy35: RX failed to go idle in 10 ms RXSM=0x2000000 [ 925.267166] ath: phy35: RX failed to go idle in 10 ms RXSM=0x2000000 [ 926.147798] usb 1-1: ath9k_htc: USB layer deinitialized [ 926.551750] usb 1-1: new high-speed USB device number 36 using ehci-platform [ 926.775032] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 927.102574] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 927.354482] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 927.634301] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 927.639954] ath9k_htc 1-1:1.0: FW RMW support: On [ 927.644774] ath: EEPROM regdomain: 0x833a [ 927.644779] ath: EEPROM indicates we should expect a country code [ 927.644794] ath: doing EEPROM country->regdmn map search [ 927.644801] ath: country maps to regdmn code: 0x37 [ 927.644808] ath: Country alpha2 being used: GB [ 927.644812] ath: Regpair used: 0x37 [ 927.699284] ieee80211 phy36: Atheros AR9271 Rev:1 [ 928.155381] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 929.552244] usb 1-1: USB disconnect, device number 36 [ 929.666070] ath: phy36: RX failed to go idle in 10 ms RXSM=0x2000000 [ 929.774329] ath: phy36: RX failed to go idle in 10 ms RXSM=0x2000000 [ 929.884017] ath: phy36: RX failed to go idle in 10 ms RXSM=0x2000000 [ 930.462405] usb 1-1: ath9k_htc: USB layer deinitialized [ 930.851712] usb 1-1: new high-speed USB device number 37 using ehci-platform [ 931.074524] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 931.383203] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 931.633998] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 931.933692] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 931.939320] ath9k_htc 1-1:1.0: FW RMW support: On [ 931.944400] ath: EEPROM regdomain: 0x833a [ 931.944407] ath: EEPROM indicates we should expect a country code [ 931.944423] ath: doing EEPROM country->regdmn map search [ 931.944431] ath: country maps to regdmn code: 0x37 [ 931.944438] ath: Country alpha2 being used: GB [ 931.944442] ath: Regpair used: 0x37 [ 931.997293] ieee80211 phy37: Atheros AR9271 Rev:1 [ 935.799753] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 937.574147] usb 1-1: USB disconnect, device number 37 [ 937.692087] ath: phy37: RX failed to go idle in 10 ms RXSM=0x2000000 [ 937.800748] ath: phy37: RX failed to go idle in 10 ms RXSM=0x2000000 [ 937.910921] ath: phy37: RX failed to go idle in 10 ms RXSM=0x2000000 [ 938.372076] usb 1-1: ath9k_htc: USB layer deinitialized [ 938.731702] usb 1-1: new high-speed USB device number 38 using ehci-platform [ 938.964863] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 939.278075] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 939.528830] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 939.820061] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 939.825753] ath9k_htc 1-1:1.0: FW RMW support: On [ 939.830533] ath: EEPROM regdomain: 0x833a [ 939.830537] ath: EEPROM indicates we should expect a country code [ 939.830554] ath: doing EEPROM country->regdmn map search [ 939.830561] ath: country maps to regdmn code: 0x37 [ 939.830568] ath: Country alpha2 being used: GB [ 939.830572] ath: Regpair used: 0x37 [ 939.850866] ieee80211 phy38: Atheros AR9271 Rev:1 [ 941.896195] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 943.392241] usb 1-1: USB disconnect, device number 38 [ 943.508126] ath: phy38: RX failed to go idle in 10 ms RXSM=0x2000000 [ 943.616725] ath: phy38: RX failed to go idle in 10 ms RXSM=0x2000000 [ 943.726403] ath: phy38: RX failed to go idle in 10 ms RXSM=0x2000000 [ 944.252084] usb 1-1: ath9k_htc: USB layer deinitialized [ 944.621708] usb 1-1: new high-speed USB device number 39 using ehci-platform [ 944.844647] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 945.172050] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 945.423065] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 945.721079] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 945.726868] ath9k_htc 1-1:1.0: FW RMW support: On [ 945.731680] ath: EEPROM regdomain: 0x833a [ 945.731684] ath: EEPROM indicates we should expect a country code [ 945.731700] ath: doing EEPROM country->regdmn map search [ 945.731707] ath: country maps to regdmn code: 0x37 [ 945.731714] ath: Country alpha2 being used: GB [ 945.731718] ath: Regpair used: 0x37 [ 945.774533] ieee80211 phy39: Atheros AR9271 Rev:1 [ 949.095388] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 950.532237] usb 1-1: USB disconnect, device number 39 [ 950.655663] ath: phy39: RX failed to go idle in 10 ms RXSM=0x2000000 [ 950.764211] ath: phy39: RX failed to go idle in 10 ms RXSM=0x2000000 [ 950.873894] ath: phy39: RX failed to go idle in 10 ms RXSM=0x2000000 [ 951.292191] usb 1-1: ath9k_htc: USB layer deinitialized [ 951.651715] usb 1-1: new high-speed USB device number 40 using ehci-platform [ 951.880052] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 952.198207] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 952.449333] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 952.707038] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 952.712747] ath9k_htc 1-1:1.0: FW RMW support: On [ 952.717546] ath: EEPROM regdomain: 0x833a [ 952.717550] ath: EEPROM indicates we should expect a country code [ 952.717567] ath: doing EEPROM country->regdmn map search [ 952.717574] ath: country maps to regdmn code: 0x37 [ 952.717581] ath: Country alpha2 being used: GB [ 952.717585] ath: Regpair used: 0x37 [ 952.734186] ieee80211 phy40: Atheros AR9271 Rev:1 [ 952.918945] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 955.004883] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 956.672418] usb 1-1: USB disconnect, device number 40 [ 956.805403] ath: phy40: RX failed to go idle in 10 ms RXSM=0x2000000 [ 956.913787] ath: phy40: RX failed to go idle in 10 ms RXSM=0x2000000 [ 957.023522] ath: phy40: RX failed to go idle in 10 ms RXSM=0x2000000 [ 957.552457] usb 1-1: ath9k_htc: USB layer deinitialized [ 957.941701] usb 1-1: new high-speed USB device number 41 using ehci-platform [ 958.164712] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 958.484306] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 958.735429] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 959.023558] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 959.029205] ath9k_htc 1-1:1.0: FW RMW support: On [ 959.034035] ath: EEPROM regdomain: 0x833a [ 959.034040] ath: EEPROM indicates we should expect a country code [ 959.034056] ath: doing EEPROM country->regdmn map search [ 959.034064] ath: country maps to regdmn code: 0x37 [ 959.034070] ath: Country alpha2 being used: GB [ 959.034075] ath: Regpair used: 0x37 [ 959.050577] ieee80211 phy41: Atheros AR9271 Rev:1 [ 960.942202] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 962.442259] usb 1-1: USB disconnect, device number 41 [ 962.575391] ath: phy41: RX failed to go idle in 10 ms RXSM=0x2000000 [ 962.683789] ath: phy41: RX failed to go idle in 10 ms RXSM=0x2000000 [ 962.793848] ath: phy41: RX failed to go idle in 10 ms RXSM=0x2000000 [ 963.202201] usb 1-1: ath9k_htc: USB layer deinitialized [ 963.561709] usb 1-1: new high-speed USB device number 42 using ehci-platform [ 963.784616] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 964.087063] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 964.340040] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 964.621939] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 964.627566] ath9k_htc 1-1:1.0: FW RMW support: On [ 964.632500] ath: EEPROM regdomain: 0x833a [ 964.632505] ath: EEPROM indicates we should expect a country code [ 964.632522] ath: doing EEPROM country->regdmn map search [ 964.632529] ath: country maps to regdmn code: 0x37 [ 964.632536] ath: Country alpha2 being used: GB [ 964.632541] ath: Regpair used: 0x37 [ 964.680469] ieee80211 phy42: Atheros AR9271 Rev:1 [ 968.251513] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 969.662246] usb 1-1: USB disconnect, device number 42 [ 969.788155] ath: phy42: RX failed to go idle in 10 ms RXSM=0x2000000 [ 969.896668] ath: phy42: RX failed to go idle in 10 ms RXSM=0x2000000 [ 970.006499] ath: phy42: RX failed to go idle in 10 ms RXSM=0x2000000 [ 970.408944] usb 1-1: ath9k_htc: USB layer deinitialized [ 970.821706] usb 1-1: new high-speed USB device number 43 using ehci-platform [ 971.044732] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 971.370824] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 971.621771] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 971.899676] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 971.905454] ath9k_htc 1-1:1.0: FW RMW support: On [ 971.910244] ath: EEPROM regdomain: 0x833a [ 971.910248] ath: EEPROM indicates we should expect a country code [ 971.910264] ath: doing EEPROM country->regdmn map search [ 971.910272] ath: country maps to regdmn code: 0x37 [ 971.910278] ath: Country alpha2 being used: GB [ 971.910282] ath: Regpair used: 0x37 [ 971.944162] ieee80211 phy43: Atheros AR9271 Rev:1 [ 972.143419] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 972.462239] usb 1-1: USB disconnect, device number 43 [ 972.578330] ath: phy43: RX failed to go idle in 10 ms RXSM=0x2000000 [ 972.686971] ath: phy43: RX failed to go idle in 10 ms RXSM=0x2000000 [ 972.796774] ath: phy43: RX failed to go idle in 10 ms RXSM=0x2000000 [ 973.702188] usb 1-1: ath9k_htc: USB layer deinitialized [ 974.081705] usb 1-1: new high-speed USB device number 44 using ehci-platform [ 974.334646] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 974.653559] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 974.904432] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 975.184043] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 975.189719] ath9k_htc 1-1:1.0: FW RMW support: On [ 975.194649] ath: EEPROM regdomain: 0x833a [ 975.194654] ath: EEPROM indicates we should expect a country code [ 975.194670] ath: doing EEPROM country->regdmn map search [ 975.194677] ath: country maps to regdmn code: 0x37 [ 975.194684] ath: Country alpha2 being used: GB [ 975.194689] ath: Regpair used: 0x37 [ 975.267316] ieee80211 phy44: Atheros AR9271 Rev:1 [ 975.743200] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 977.086360] usb 1-1: USB disconnect, device number 44 [ 977.199923] ath: phy44: RX failed to go idle in 10 ms RXSM=0x2000000 [ 977.308376] ath: phy44: RX failed to go idle in 10 ms RXSM=0x2000000 [ 977.418281] ath: phy44: RX failed to go idle in 10 ms RXSM=0x2000000 [ 978.061100] usb 1-1: ath9k_htc: USB layer deinitialized [ 978.422086] usb 1-1: new high-speed USB device number 45 using ehci-platform [ 978.644512] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 978.944332] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 979.197201] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 979.470795] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 979.476459] ath9k_htc 1-1:1.0: FW RMW support: On [ 979.481353] ath: EEPROM regdomain: 0x833a [ 979.481358] ath: EEPROM indicates we should expect a country code [ 979.481375] ath: doing EEPROM country->regdmn map search [ 979.481383] ath: country maps to regdmn code: 0x37 [ 979.481389] ath: Country alpha2 being used: GB [ 979.481394] ath: Regpair used: 0x37 [ 979.537659] ieee80211 phy45: Atheros AR9271 Rev:1 [ 983.197633] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 985.032234] usb 1-1: USB disconnect, device number 45 [ 985.162847] ath: phy45: RX failed to go idle in 10 ms RXSM=0x2000000 [ 985.271088] ath: phy45: RX failed to go idle in 10 ms RXSM=0x2000000 [ 985.380726] ath: phy45: RX failed to go idle in 10 ms RXSM=0x2000000 [ 985.806117] usb 1-1: ath9k_htc: USB layer deinitialized [ 986.201704] usb 1-1: new high-speed USB device number 46 using ehci-platform [ 986.424517] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 986.735699] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 986.986681] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 987.283593] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 987.289356] ath9k_htc 1-1:1.0: FW RMW support: On [ 987.294196] ath: EEPROM regdomain: 0x833a [ 987.294200] ath: EEPROM indicates we should expect a country code [ 987.294217] ath: doing EEPROM country->regdmn map search [ 987.294224] ath: country maps to regdmn code: 0x37 [ 987.294231] ath: Country alpha2 being used: GB [ 987.294235] ath: Regpair used: 0x37 [ 987.322545] ieee80211 phy46: Atheros AR9271 Rev:1 [ 989.353881] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 990.842717] usb 1-1: USB disconnect, device number 46 [ 990.958689] ath: phy46: RX failed to go idle in 10 ms RXSM=0x2000000 [ 991.067267] ath: phy46: RX failed to go idle in 10 ms RXSM=0x2000000 [ 991.181046] ath: phy46: RX failed to go idle in 10 ms RXSM=0x2000000 [ 991.622408] usb 1-1: ath9k_htc: USB layer deinitialized [ 992.001702] usb 1-1: new high-speed USB device number 47 using ehci-platform [ 992.234774] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 992.543057] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 992.796062] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 993.086095] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 993.091764] ath9k_htc 1-1:1.0: FW RMW support: On [ 993.096546] ath: EEPROM regdomain: 0x833a [ 993.096550] ath: EEPROM indicates we should expect a country code [ 993.096566] ath: doing EEPROM country->regdmn map search [ 993.096574] ath: country maps to regdmn code: 0x37 [ 993.096581] ath: Country alpha2 being used: GB [ 993.096585] ath: Regpair used: 0x37 [ 993.159199] ieee80211 phy47: Atheros AR9271 Rev:1 [ 996.696883] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 998.192242] usb 1-1: USB disconnect, device number 47 [ 998.317934] ath: phy47: RX failed to go idle in 10 ms RXSM=0x2000000 [ 998.426233] ath: phy47: RX failed to go idle in 10 ms RXSM=0x2000000 [ 998.536042] ath: phy47: RX failed to go idle in 10 ms RXSM=0x2000000 [ 998.952195] usb 1-1: ath9k_htc: USB layer deinitialized [ 999.311713] usb 1-1: new high-speed USB device number 48 using ehci-platform [ 999.534642] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 999.838302] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1000.089450] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1000.360352] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1000.366014] ath9k_htc 1-1:1.0: FW RMW support: On [ 1000.370906] ath: EEPROM regdomain: 0x833a [ 1000.370911] ath: EEPROM indicates we should expect a country code [ 1000.370927] ath: doing EEPROM country->regdmn map search [ 1000.370935] ath: country maps to regdmn code: 0x37 [ 1000.370942] ath: Country alpha2 being used: GB [ 1000.370946] ath: Regpair used: 0x37 [ 1000.386813] ieee80211 phy48: Atheros AR9271 Rev:1 [ 1000.556262] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1000.862240] usb 1-1: USB disconnect, device number 48 [ 1000.981325] ath: phy48: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1001.093460] ath: phy48: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1001.204210] ath: phy48: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1002.072071] usb 1-1: ath9k_htc: USB layer deinitialized [ 1002.471811] usb 1-1: new high-speed USB device number 49 using ehci-platform [ 1002.694660] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1003.027913] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1003.278679] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1003.580740] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1003.586434] ath9k_htc 1-1:1.0: FW RMW support: On [ 1003.591306] ath: EEPROM regdomain: 0x833a [ 1003.591311] ath: EEPROM indicates we should expect a country code [ 1003.591327] ath: doing EEPROM country->regdmn map search [ 1003.591335] ath: country maps to regdmn code: 0x37 [ 1003.591341] ath: Country alpha2 being used: GB [ 1003.591346] ath: Regpair used: 0x37 [ 1003.651663] ieee80211 phy49: Atheros AR9271 Rev:1 [ 1004.141811] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1005.472180] usb 1-1: USB disconnect, device number 49 [ 1005.591566] ath: phy49: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1005.700017] ath: phy49: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1005.809775] ath: phy49: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1006.402642] usb 1-1: ath9k_htc: USB layer deinitialized [ 1006.771721] usb 1-1: new high-speed USB device number 50 using ehci-platform [ 1007.001765] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1007.305179] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1007.556291] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1007.846454] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1007.852113] ath9k_htc 1-1:1.0: FW RMW support: On [ 1007.857042] ath: EEPROM regdomain: 0x833a [ 1007.857047] ath: EEPROM indicates we should expect a country code [ 1007.857064] ath: doing EEPROM country->regdmn map search [ 1007.857071] ath: country maps to regdmn code: 0x37 [ 1007.857078] ath: Country alpha2 being used: GB [ 1007.857082] ath: Regpair used: 0x37 [ 1007.917297] ieee80211 phy50: Atheros AR9271 Rev:1 [ 1011.547137] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1013.342236] usb 1-1: USB disconnect, device number 50 [ 1013.462936] ath: phy50: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1013.571512] ath: phy50: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1013.681575] ath: phy50: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1014.092066] usb 1-1: ath9k_htc: USB layer deinitialized [ 1014.471722] usb 1-1: new high-speed USB device number 51 using ehci-platform [ 1014.704964] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1015.011270] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1015.261811] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1015.533561] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1015.539327] ath9k_htc 1-1:1.0: FW RMW support: On [ 1015.544178] ath: EEPROM regdomain: 0x833a [ 1015.544183] ath: EEPROM indicates we should expect a country code [ 1015.544199] ath: doing EEPROM country->regdmn map search [ 1015.544207] ath: country maps to regdmn code: 0x37 [ 1015.544214] ath: Country alpha2 being used: GB [ 1015.544218] ath: Regpair used: 0x37 [ 1015.577018] ieee80211 phy51: Atheros AR9271 Rev:1 [ 1017.724301] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1019.213382] usb 1-1: USB disconnect, device number 51 [ 1019.345128] ath: phy51: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1019.453542] ath: phy51: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1019.563438] ath: phy51: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1019.982207] usb 1-1: ath9k_htc: USB layer deinitialized [ 1020.341704] usb 1-1: new high-speed USB device number 52 using ehci-platform [ 1020.574526] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1020.877696] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1021.128537] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1021.418468] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1021.424135] ath9k_htc 1-1:1.0: FW RMW support: On [ 1021.428940] ath: EEPROM regdomain: 0x833a [ 1021.428945] ath: EEPROM indicates we should expect a country code [ 1021.428962] ath: doing EEPROM country->regdmn map search [ 1021.428969] ath: country maps to regdmn code: 0x37 [ 1021.428976] ath: Country alpha2 being used: GB [ 1021.428980] ath: Regpair used: 0x37 [ 1021.509175] ieee80211 phy52: Atheros AR9271 Rev:1 [ 1025.010030] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1026.416553] usb 1-1: USB disconnect, device number 52 [ 1026.543409] ath: phy52: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1026.651688] ath: phy52: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1026.761368] ath: phy52: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1027.165026] usb 1-1: ath9k_htc: USB layer deinitialized [ 1027.551699] usb 1-1: new high-speed USB device number 53 using ehci-platform [ 1027.774702] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1028.091740] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1028.343934] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1028.608690] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1028.614361] ath9k_htc 1-1:1.0: FW RMW support: On [ 1028.619164] ath: EEPROM regdomain: 0x833a [ 1028.619169] ath: EEPROM indicates we should expect a country code [ 1028.619185] ath: doing EEPROM country->regdmn map search [ 1028.619193] ath: country maps to regdmn code: 0x37 [ 1028.619199] ath: Country alpha2 being used: GB [ 1028.619203] ath: Regpair used: 0x37 [ 1028.635821] ieee80211 phy53: Atheros AR9271 Rev:1 [ 1028.815136] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1029.122247] usb 1-1: USB disconnect, device number 53 [ 1029.243588] ath: phy53: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1029.351927] ath: phy53: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1029.461706] ath: phy53: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1030.132434] usb 1-1: ath9k_htc: USB layer deinitialized [ 1030.521707] usb 1-1: new high-speed USB device number 54 using ehci-platform [ 1030.754594] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1031.077157] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1031.328048] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1031.611559] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1031.617282] ath9k_htc 1-1:1.0: FW RMW support: On [ 1031.622112] ath: EEPROM regdomain: 0x833a [ 1031.622117] ath: EEPROM indicates we should expect a country code [ 1031.622133] ath: doing EEPROM country->regdmn map search [ 1031.622141] ath: country maps to regdmn code: 0x37 [ 1031.622147] ath: Country alpha2 being used: GB [ 1031.622152] ath: Regpair used: 0x37 [ 1031.664910] ieee80211 phy54: Atheros AR9271 Rev:1 [ 1034.199522] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1035.682244] usb 1-1: USB disconnect, device number 54 [ 1035.798444] ath: phy54: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1035.906970] ath: phy54: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1036.016986] ath: phy54: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1036.892191] usb 1-1: ath9k_htc: USB layer deinitialized [ 1037.261718] usb 1-1: new high-speed USB device number 55 using ehci-platform [ 1037.484681] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1037.794575] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1038.045555] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1038.315549] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1038.321199] ath9k_htc 1-1:1.0: FW RMW support: On [ 1038.326030] ath: EEPROM regdomain: 0x833a [ 1038.326035] ath: EEPROM indicates we should expect a country code [ 1038.326051] ath: doing EEPROM country->regdmn map search [ 1038.326059] ath: country maps to regdmn code: 0x37 [ 1038.326065] ath: Country alpha2 being used: GB [ 1038.326070] ath: Regpair used: 0x37 [ 1038.356823] ieee80211 phy55: Atheros AR9271 Rev:1 [ 1038.538966] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1038.852257] usb 1-1: USB disconnect, device number 55 [ 1038.968272] ath: phy55: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1039.076567] ath: phy55: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1039.189982] ath: phy55: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1040.087632] usb 1-1: ath9k_htc: USB layer deinitialized [ 1040.481946] usb 1-1: new high-speed USB device number 56 using ehci-platform [ 1040.734697] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested [ 1041.039200] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 [ 1041.290190] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits [ 1041.624934] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 [ 1041.630560] ath9k_htc 1-1:1.0: FW RMW support: On [ 1041.635492] ath: EEPROM regdomain: 0x833a [ 1041.635498] ath: EEPROM indicates we should expect a country code [ 1041.635515] ath: doing EEPROM country->regdmn map search [ 1041.635522] ath: country maps to regdmn code: 0x37 [ 1041.635529] ath: Country alpha2 being used: GB [ 1041.635533] ath: Regpair used: 0x37 [ 1041.699326] ieee80211 phy56: Atheros AR9271 Rev:1 [ 1042.161585] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready [ 1043.462246] usb 1-1: USB disconnect, device number 56 [ 1043.577630] ath: phy56: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1043.686193] ath: phy56: RX failed to go idle in 10 ms RXSM=0x2000000 [ 1043.796049] ath: phy56: RX failed to go idle in 10 ms RXSM=0x2000000 Here is the system log: Sun Dec 29 02:02:56 2019 kern.debug kernel: [ 1000.370946] ath: Regpair used: 0x37 Sun Dec 29 02:02:56 2019 daemon.notice netifd: Network device 'wlan2' link is up Sun Dec 29 02:02:56 2019 kern.info kernel: [ 1000.386813] ieee80211 phy48: Atheros AR9271 Rev:1 Sun Dec 29 02:02:56 2019 daemon.notice netifd: Network device 'wlan2' link is down Sun Dec 29 02:02:56 2019 kern.info kernel: [ 1000.556262] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:02:57 2019 kern.info kernel: [ 1000.862240] usb 1-1: USB disconnect, device number 48 Sun Dec 29 02:02:57 2019 kern.err kernel: [ 1000.981325] ath: phy48: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:02:57 2019 kern.err kernel: [ 1001.093460] ath: phy48: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:02:57 2019 kern.err kernel: [ 1001.204210] ath: phy48: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:02:58 2019 kern.info kernel: [ 1002.072071] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:02:58 2019 daemon.notice netifd: radio2 (17914): command failed: No such device (-19) Sun Dec 29 02:02:58 2019 kern.info kernel: [ 1002.471811] usb 1-1: new high-speed USB device number 49 using ehci-platform Sun Dec 29 02:02:59 2019 kern.info kernel: [ 1002.694660] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): command failed: No such file or directory (-2) Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): command failed: No such file or directory (-2) Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): cat: can't open '/sys/class/ieee80211/phy48/macaddress': No such file or directory Sun Dec 29 02:02:59 2019 kern.info kernel: [ 1003.027913] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): cat: can't open '/sys/class/ieee80211/phy48/address_mask': No such file or directory Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): ./mac80211.sh: eval: line 371: arithmetic syntax error Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): command failed: No such file or directory (-2) Sun Dec 29 02:02:59 2019 kern.info kernel: [ 1003.278679] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Usage: iw [options] command Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Options: Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): --debug enable netlink debugging Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): --version show version (5.0.1) Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Commands: Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): help [command] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Print usage for all or a specific command, e.g. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): "help wowlan" or "help wowlan enable". Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): event [-t|-r] [-f] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Monitor events from the kernel. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): -t - print timestamp Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): -r - print relative timstamp Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): -f - print full frame for auth/assoc etc. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): features Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): phy Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): list Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): List all wireless devices and their capabilities. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): phy <phyname> info Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Show capabilities for the specified wireless device. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): phy <phyname> channels Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Show available channels. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): List all network interfaces for wireless hardware. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> info Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Show information for this interface. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> del Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Remove this virtual interface Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*] [addr <mac-addr>] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*] [addr <mac-addr>] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Add a new virtual interface with the given configuration. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Valid interface types are: managed, ibss, monitor, mesh, wds. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): The flags are only used for monitor interfaces, valid flags are: Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): none: no special flags Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): fcsfail: show frames with FCS errors Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): control: show control frames Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): otherbss: show frames from other BSSes Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): cook: use cooked mode Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): active: use active mode (ACK incoming unicast packets) Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): mumimo-groupid <GROUP_ID>: use MUMIMO according to a group id Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): mumimo-follow-mac <MAC_ADDRESS>: use MUMIMO according to a MAC address Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): The mesh_id is used only for mesh mode. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> ibss join <SSID> <freq in MHz> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Join the IBSS cell with the given SSID, if it doesn't exist create Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): it on the given frequency. When fixed frequency is requested, don't Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): join/create a cell on a different frequency. When a fixed BSSID is Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): requested use that BSSID and do not adopt another cell's BSSID even Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): if it has higher TSF and the same SSID. If an IBSS is created, create Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): it with the specified basic-rates, multicast-rate and beacon-interval. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> ibss leave Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Leave the current IBSS cell. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> station dump [-v] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): List all stations known, e.g. the AP on managed interfaces Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> station set <MAC address> vlan <ifindex> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Set an AP VLAN for this station. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> station del <MAC address> [subtype <subtype>] [reason-code <code>] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Remove the given station entry (use with caution!) Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Example subtype values: 0xA (disassociation), 0xC (deauthentication) Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> station get <MAC address> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Get information for a specific station. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> survey dump Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): List all gathered channel survey data Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mesh leave Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Leave a mesh. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mesh join <mesh ID> [[freq <freq in MHz> <NOHT|HT20|HT40+|HT40-|80MHz>] [basic-rates <rate in Mbps,rate2,...>]], [mcast-rate <rate in Mbps>] [beacon-interval <time in TUs>] [dtim-period <value>] [vendor_sync on|off] [<param>=<value>]* Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Join a mesh with the given mesh ID with frequency, basic-rates, Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): mcast-rate and mesh parameters. Basic-rates are applied only if Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): frequency is provided. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpath dump Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): List known mesh paths. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Set an existing mesh path's next hop. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Create a new mesh path (instead of relying on automatic discovery). Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpath del <MAC address> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Remove the mesh path to the given node. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpath get <MAC address> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Get information on mesh path to the given node. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpp dump Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): List known mesh proxy paths. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> mpp get <MAC address> Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Get information on mesh proxy path to the given node. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> scan [-u] [freq <freq>*] [duration <dur>] [ies <hex as 00:11:..>] [meshid <meshid>] [lowpri,flush,ap-force,duration-mandatory] [randomise[=<addr>/<mask>]] [ssid <ssid>*|passive] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Scan on the given frequencies and probe for the given SSIDs Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): (or wildcard if not given) unless passive scanning is requested. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): If -u is specified print unknown data in the scan results. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Specified (vendor) IEs must be well-formed. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> scan abort Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Abort ongoing scan Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> scan trigger [freq <freq>*] [duration <dur>] [ies <hex as 00:11:..>] [meshid <meshid>] [lowpri,flush,ap-force,duration-mandatory] [randomise[=<addr>/<mask>]] [ssid <ssid>*|passive] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Trigger a scan on the given frequencies with probing for the given Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): SSIDs (or wildcard if not given) unless passive scanning is requested. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Duration(in TUs), if specified, will be used to set dwell times. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): dev <devname> scan dump [-u] Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Dump the current scan results. If -u is specified, print unknown Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): data in scan results. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): reg reload Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Reload the kernel's regulatory database. Sun Dec 29 02:02:59 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 kern.info kernel: [ 1003.580740] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:00 2019 kern.info kernel: [ 1003.586434] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:00 2019 kern.debug kernel: [ 1003.591306] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:00 2019 kern.debug kernel: [ 1003.591311] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:00 2019 kern.debug kernel: [ 1003.591327] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:00 2019 kern.debug kernel: [ 1003.591335] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:00 2019 kern.debug kernel: [ 1003.591341] ath: Country alpha2 being used: GB Sun Dec 29 02:03:00 2019 kern.debug kernel: [ 1003.591346] ath: Regpair used: 0x37 Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> reg get Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Print out the devices' current regulatory domain information. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): reg get Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Print out the kernel's current regulatory domain information. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): reg set <ISO/IEC 3166-1 alpha2> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Notify the kernel about the current regulatory domain. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> auth <SSID> <bssid> <type:open|shared> <freq in MHz> [key 0:abcde d:1:6162636465] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Authenticate with the given network. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465] [mfp:req/opt/no] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Join the network with the given SSID (and frequency, BSSID). Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): With -w, wait for the connect to finish or fail. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> disconnect Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Disconnect from the current network. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> link Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Print information about the current link, if any. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set antenna_gain <antenna gain in dBm> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Specify antenna gain. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set txq limit <packets> | memory_limit <bytes> | quantum <bytes> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set TXQ parameters. The limit and memory_limit are global queue limits Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): for the whole phy. The quantum is the DRR scheduler quantum setting. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Valid values: 1 - 2**32 Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set a bitmap of allowed antennas to use for TX and RX. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): The driver may reject antenna configurations it cannot support. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Specify transmit power level and setting type. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Specify transmit power level and setting type. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set distance <auto|distance> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Enable ACK timeout estimation algorithm (dynack) or set appropriate Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): coverage class for given link distance in meters. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): To disable dynack set valid value for coverage class. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Valid values: 0 - 114750 Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set coverage <coverage class> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set coverage class (1 for every 3 usec of air propagation time). Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Valid values: 0 - 255. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set netns { <pid> | name <nsname> } Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Put this wireless device into a different network namespace: Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): <pid> - change network namespace by process id Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): <nsname> - change network namespace by name from /var/run/netns Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): or by absolute path (man ip-netns) Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set retry [short <limit>] [long <limit>] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set retry limit. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set rts <rts threshold|off> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set rts threshold. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set frag <fragmentation threshold|off> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set fragmentation threshold. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set frequency/channel the hardware is using, including HT Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): configuration. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> set name <new name> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Rename this wireless device. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set mcast_rate <rate in Mbps> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set the multicast bitrate. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set noack_map <map> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO) Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set 4addr <on|off> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set interface 4addr (WDS) mode. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set type <type> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set interface type/mode. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Valid interface types are: managed, ibss, monitor, mesh, wds. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set meshid <meshid> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set monitor <flag>* Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set monitor flags. Valid flags are: Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): none: no special flags Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): fcsfail: show frames with FCS errors Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): control: show control frames Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): otherbss: show frames from other BSSes Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): cook: use cooked mode Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): active: use active mode (ACK incoming unicast packets) Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): mumimo-groupid <GROUP_ID>: use MUMIMO according to a group id Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): mumimo-follow-mac <MAC_ADDRESS>: use MUMIMO according to a MAC address Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set mesh_param <param>=<value> [<param>=<value>]* Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set mesh parameter (run command without any to see available ones). Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set power_save <on|off> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Set power save state to on or off. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [ht-mcs-<2.4|5> <MCS index>*] [vht-mcs-<2.4|5> <NSS:MCSx,MCSy... | NSS:MCSx-MCSy>*] [sgi-2.4|lgi-2.4] [sgi-5|lgi-5] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sets up the specified rate masks. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Not passing any arguments would clear the existing mask (if any). Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): phy <phyname> get txq Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Get TXQ parameters. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> get mesh_param [<param>] Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Retrieve mesh parameter (run command without any to see available ones). Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): dev <devname> get power_save <param> Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Retrieve power save state. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Commands that use the netdev ('dev') can also be given the Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): 'wdev' instead to identify the device. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): You can omit the 'phy' or 'dev' if the identification is unique, Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.) Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Do NOT screenscrape this tool, we don't consider its output stable. Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): ifconfig: invalid hw-addr Sun Dec 29 02:03:00 2019 kern.info kernel: [ 1003.651663] ieee80211 phy49: Atheros AR9271 Rev:1 Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): cat: can't open '/sys/class/ieee80211/phy48/macaddress': No such file or directory Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): cat: can't open '/sys/class/ieee80211/phy48/address_mask': No such file or directory Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): ./mac80211.sh: eval: line 371: arithmetic syntax error Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): command failed: No such file or directory (-2) Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): ifconfig: invalid hw-addr Sun Dec 29 02:03:00 2019 kern.info kernel: [ 1004.141811] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:00 2019 daemon.notice netifd: radio2 (17914): Successfully initialized wpa_supplicant Sun Dec 29 02:03:01 2019 kern.info kernel: [ 1005.472180] usb 1-1: USB disconnect, device number 49 Sun Dec 29 02:03:01 2019 daemon.notice netifd: radio2 (17914): Interface 1 setup failed: BRIDGE_NOT_ALLOWED Sun Dec 29 02:03:02 2019 kern.err kernel: [ 1005.591566] ath: phy49: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:02 2019 kern.err kernel: [ 1005.700017] ath: phy49: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:02 2019 kern.err kernel: [ 1005.809775] ath: phy49: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:02 2019 kern.info kernel: [ 1006.402642] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:03 2019 kern.info kernel: [ 1006.771721] usb 1-1: new high-speed USB device number 50 using ehci-platform Sun Dec 29 02:03:03 2019 kern.info kernel: [ 1007.001765] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:03 2019 kern.info kernel: [ 1007.305179] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:03 2019 kern.info kernel: [ 1007.556291] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:04 2019 kern.info kernel: [ 1007.846454] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:04 2019 kern.info kernel: [ 1007.852113] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:04 2019 kern.debug kernel: [ 1007.857042] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:04 2019 kern.debug kernel: [ 1007.857047] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:04 2019 kern.debug kernel: [ 1007.857064] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:04 2019 kern.debug kernel: [ 1007.857071] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:04 2019 kern.debug kernel: [ 1007.857078] ath: Country alpha2 being used: GB Sun Dec 29 02:03:04 2019 kern.debug kernel: [ 1007.857082] ath: Regpair used: 0x37 Sun Dec 29 02:03:04 2019 daemon.notice netifd: radio2 (18263): Could not find PHY for device 'radio2' Sun Dec 29 02:03:04 2019 kern.info kernel: [ 1007.917297] ieee80211 phy50: Atheros AR9271 Rev:1 Sun Dec 29 02:03:04 2019 daemon.notice netifd: radio2 (18298): WARNING: Variable 'data' does not exist or is not an array/object Sun Dec 29 02:03:07 2019 daemon.notice netifd: radio2 (18411): command failed: Too many open files in system (-23) Sun Dec 29 02:03:07 2019 kern.info kernel: [ 1011.547137] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:08 2019 daemon.notice netifd: radio2 (18411): Successfully initialized wpa_supplicant Sun Dec 29 02:03:09 2019 daemon.notice netifd: radio2 (18411): Interface 1 setup failed: BRIDGE_NOT_ALLOWED Sun Dec 29 02:03:09 2019 kern.info kernel: [ 1013.342236] usb 1-1: USB disconnect, device number 50 Sun Dec 29 02:03:10 2019 kern.err kernel: [ 1013.462936] ath: phy50: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:10 2019 kern.err kernel: [ 1013.571512] ath: phy50: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:10 2019 kern.err kernel: [ 1013.681575] ath: phy50: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:10 2019 daemon.notice netifd: Interface 'wwan' is enabled Sun Dec 29 02:03:10 2019 daemon.notice netifd: Interface 'wwan' is disabled Sun Dec 29 02:03:10 2019 kern.info kernel: [ 1014.092066] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:10 2019 kern.info kernel: [ 1014.471722] usb 1-1: new high-speed USB device number 51 using ehci-platform Sun Dec 29 02:03:11 2019 kern.info kernel: [ 1014.704964] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:11 2019 daemon.notice netifd: radio2 (18684): Could not find PHY for device 'radio2' Sun Dec 29 02:03:11 2019 kern.info kernel: [ 1015.011270] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:11 2019 kern.info kernel: [ 1015.261811] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:11 2019 daemon.notice netifd: radio2 (18709): WARNING: Variable 'data' does not exist or is not an array/object Sun Dec 29 02:03:11 2019 kern.info kernel: [ 1015.533561] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:11 2019 kern.info kernel: [ 1015.539327] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:11 2019 kern.debug kernel: [ 1015.544178] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:11 2019 kern.debug kernel: [ 1015.544183] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:11 2019 kern.debug kernel: [ 1015.544199] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:11 2019 kern.debug kernel: [ 1015.544207] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:11 2019 kern.debug kernel: [ 1015.544214] ath: Country alpha2 being used: GB Sun Dec 29 02:03:11 2019 kern.debug kernel: [ 1015.544218] ath: Regpair used: 0x37 Sun Dec 29 02:03:12 2019 kern.info kernel: [ 1015.577018] ieee80211 phy51: Atheros AR9271 Rev:1 Sun Dec 29 02:03:13 2019 daemon.notice netifd: radio2 (18763): command failed: Too many open files in system (-23) Sun Dec 29 02:03:14 2019 kern.info kernel: [ 1017.724301] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:14 2019 daemon.notice netifd: radio2 (18763): Successfully initialized wpa_supplicant Sun Dec 29 02:03:15 2019 kern.info kernel: [ 1019.213382] usb 1-1: USB disconnect, device number 51 Sun Dec 29 02:03:15 2019 daemon.notice netifd: radio2 (18763): Interface 1 setup failed: BRIDGE_NOT_ALLOWED Sun Dec 29 02:03:15 2019 kern.err kernel: [ 1019.345128] ath: phy51: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:15 2019 kern.err kernel: [ 1019.453542] ath: phy51: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:15 2019 kern.err kernel: [ 1019.563438] ath: phy51: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:16 2019 daemon.notice netifd: Interface 'wwan' is enabled Sun Dec 29 02:03:16 2019 daemon.notice netifd: Interface 'wwan' is disabled Sun Dec 29 02:03:16 2019 kern.info kernel: [ 1019.982207] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:16 2019 kern.info kernel: [ 1020.341704] usb 1-1: new high-speed USB device number 52 using ehci-platform Sun Dec 29 02:03:17 2019 kern.info kernel: [ 1020.574526] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:17 2019 kern.info kernel: [ 1020.877696] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:17 2019 daemon.notice netifd: radio2 (19029): Could not find PHY for device 'radio2' Sun Dec 29 02:03:17 2019 kern.info kernel: [ 1021.128537] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:17 2019 kern.info kernel: [ 1021.418468] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:17 2019 kern.info kernel: [ 1021.424135] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:17 2019 kern.debug kernel: [ 1021.428940] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:17 2019 kern.debug kernel: [ 1021.428945] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:17 2019 kern.debug kernel: [ 1021.428962] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:17 2019 kern.debug kernel: [ 1021.428969] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:17 2019 kern.debug kernel: [ 1021.428976] ath: Country alpha2 being used: GB Sun Dec 29 02:03:17 2019 kern.debug kernel: [ 1021.428980] ath: Regpair used: 0x37 Sun Dec 29 02:03:17 2019 daemon.notice netifd: radio2 (19061): WARNING: Variable 'data' does not exist or is not an array/object Sun Dec 29 02:03:17 2019 kern.info kernel: [ 1021.509175] ieee80211 phy52: Atheros AR9271 Rev:1 Sun Dec 29 02:03:21 2019 daemon.notice netifd: radio2 (19216): command failed: Too many open files in system (-23) Sun Dec 29 02:03:21 2019 kern.info kernel: [ 1025.010030] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:21 2019 daemon.notice netifd: radio2 (19216): Successfully initialized wpa_supplicant Sun Dec 29 02:03:22 2019 kern.info kernel: [ 1026.416553] usb 1-1: USB disconnect, device number 52 Sun Dec 29 02:03:23 2019 kern.err kernel: [ 1026.543409] ath: phy52: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:23 2019 kern.err kernel: [ 1026.651688] ath: phy52: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:23 2019 kern.err kernel: [ 1026.761368] ath: phy52: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:23 2019 daemon.notice netifd: radio2 (19216): ifconfig: SIOCSIFFLAGS: No such device Sun Dec 29 02:03:23 2019 daemon.notice netifd: radio2 (19216): Interface 1 setup failed: IFUP_ERROR Sun Dec 29 02:03:23 2019 kern.info kernel: [ 1027.165026] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:23 2019 kern.info kernel: [ 1027.551699] usb 1-1: new high-speed USB device number 53 using ehci-platform Sun Dec 29 02:03:24 2019 kern.info kernel: [ 1027.774702] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:24 2019 kern.info kernel: [ 1028.091740] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:24 2019 kern.info kernel: [ 1028.343934] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:25 2019 kern.info kernel: [ 1028.608690] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:25 2019 kern.info kernel: [ 1028.614361] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:25 2019 kern.debug kernel: [ 1028.619164] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:25 2019 kern.debug kernel: [ 1028.619169] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:25 2019 kern.debug kernel: [ 1028.619185] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:25 2019 kern.debug kernel: [ 1028.619193] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:25 2019 kern.debug kernel: [ 1028.619199] ath: Country alpha2 being used: GB Sun Dec 29 02:03:25 2019 kern.debug kernel: [ 1028.619203] ath: Regpair used: 0x37 Sun Dec 29 02:03:25 2019 kern.info kernel: [ 1028.635821] ieee80211 phy53: Atheros AR9271 Rev:1 Sun Dec 29 02:03:25 2019 kern.info kernel: [ 1028.815136] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:25 2019 kern.info kernel: [ 1029.122247] usb 1-1: USB disconnect, device number 53 Sun Dec 29 02:03:25 2019 kern.err kernel: [ 1029.243588] ath: phy53: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:25 2019 kern.err kernel: [ 1029.351927] ath: phy53: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:25 2019 kern.err kernel: [ 1029.461706] ath: phy53: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:26 2019 kern.info kernel: [ 1030.132434] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:26 2019 kern.info kernel: [ 1030.521707] usb 1-1: new high-speed USB device number 54 using ehci-platform Sun Dec 29 02:03:27 2019 kern.info kernel: [ 1030.754594] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:27 2019 daemon.notice netifd: radio2 (19634): Could not find PHY for device 'radio2' Sun Dec 29 02:03:27 2019 kern.info kernel: [ 1031.077157] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:27 2019 kern.info kernel: [ 1031.328048] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:28 2019 daemon.notice netifd: radio2 (19670): WARNING: Variable 'data' does not exist or is not an array/object Sun Dec 29 02:03:28 2019 kern.info kernel: [ 1031.611559] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:28 2019 kern.info kernel: [ 1031.617282] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:28 2019 kern.debug kernel: [ 1031.622112] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:28 2019 kern.debug kernel: [ 1031.622117] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:28 2019 kern.debug kernel: [ 1031.622133] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:28 2019 kern.debug kernel: [ 1031.622141] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:28 2019 kern.debug kernel: [ 1031.622147] ath: Country alpha2 being used: GB Sun Dec 29 02:03:28 2019 kern.debug kernel: [ 1031.622152] ath: Regpair used: 0x37 Sun Dec 29 02:03:28 2019 kern.info kernel: [ 1031.664910] ieee80211 phy54: Atheros AR9271 Rev:1 Sun Dec 29 02:03:30 2019 daemon.notice netifd: radio2 (19761): command failed: Too many open files in system (-23) Sun Dec 29 02:03:30 2019 kern.info kernel: [ 1034.199522] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:30 2019 daemon.notice netifd: radio2 (19761): Successfully initialized wpa_supplicant Sun Dec 29 02:03:32 2019 kern.info kernel: [ 1035.682244] usb 1-1: USB disconnect, device number 54 Sun Dec 29 02:03:32 2019 kern.err kernel: [ 1035.798444] ath: phy54: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:32 2019 kern.err kernel: [ 1035.906970] ath: phy54: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:32 2019 kern.err kernel: [ 1036.016986] ath: phy54: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:33 2019 daemon.notice netifd: radio2 (19761): ifconfig: SIOCSIFFLAGS: No such device Sun Dec 29 02:03:33 2019 daemon.notice netifd: radio2 (19761): Interface 1 setup failed: IFUP_ERROR Sun Dec 29 02:03:33 2019 kern.info kernel: [ 1036.892191] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:33 2019 kern.info kernel: [ 1037.261718] usb 1-1: new high-speed USB device number 55 using ehci-platform Sun Dec 29 02:03:33 2019 kern.info kernel: [ 1037.484681] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:34 2019 kern.info kernel: [ 1037.794575] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:34 2019 kern.info kernel: [ 1038.045555] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:34 2019 kern.info kernel: [ 1038.315549] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:34 2019 kern.info kernel: [ 1038.321199] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:34 2019 kern.debug kernel: [ 1038.326030] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:34 2019 kern.debug kernel: [ 1038.326035] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:34 2019 kern.debug kernel: [ 1038.326051] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:34 2019 kern.debug kernel: [ 1038.326059] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:34 2019 kern.debug kernel: [ 1038.326065] ath: Country alpha2 being used: GB Sun Dec 29 02:03:34 2019 kern.debug kernel: [ 1038.326070] ath: Regpair used: 0x37 Sun Dec 29 02:03:34 2019 daemon.notice netifd: Network device 'wlan2' link is up Sun Dec 29 02:03:34 2019 kern.info kernel: [ 1038.356823] ieee80211 phy55: Atheros AR9271 Rev:1 Sun Dec 29 02:03:34 2019 daemon.notice netifd: Network device 'wlan2' link is down Sun Dec 29 02:03:34 2019 kern.info kernel: [ 1038.538966] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:35 2019 kern.info kernel: [ 1038.852257] usb 1-1: USB disconnect, device number 55 Sun Dec 29 02:03:35 2019 kern.err kernel: [ 1038.968272] ath: phy55: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:35 2019 kern.err kernel: [ 1039.076567] ath: phy55: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:35 2019 kern.err kernel: [ 1039.189982] ath: phy55: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:36 2019 kern.info kernel: [ 1040.087632] usb 1-1: ath9k_htc: USB layer deinitialized Sun Dec 29 02:03:36 2019 kern.info kernel: [ 1040.481946] usb 1-1: new high-speed USB device number 56 using ehci-platform Sun Dec 29 02:03:36 2019 daemon.notice netifd: radio2 (20122): command failed: No such device (-19) Sun Dec 29 02:03:37 2019 kern.info kernel: [ 1040.734697] usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): command failed: No such file or directory (-2) Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): command failed: No such file or directory (-2) Sun Dec 29 02:03:37 2019 kern.info kernel: [ 1041.039200] usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): cat: can't open '/sys/class/ieee80211/phy55/macaddress': No such file or directory Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): cat: can't open '/sys/class/ieee80211/phy55/address_mask': No such file or directory Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): ./mac80211.sh: eval: line 371: arithmetic syntax error Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): command failed: No such file or directory (-2) Sun Dec 29 02:03:37 2019 kern.info kernel: [ 1041.290190] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Usage: iw [options] command Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Options: Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): --debug enable netlink debugging Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): --version show version (5.0.1) Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Commands: Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): help [command] Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Print usage for all or a specific command, e.g. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): "help wowlan" or "help wowlan enable". Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): event [-t|-r] [-f] Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Monitor events from the kernel. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): -t - print timestamp Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): -r - print relative timstamp Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): -f - print full frame for auth/assoc etc. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): features Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): phy Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): list Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): List all wireless devices and their capabilities. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): phy <phyname> info Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Show capabilities for the specified wireless device. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): phy <phyname> channels Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Show available channels. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): dev Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): List all network interfaces for wireless hardware. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): dev <devname> info Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Show information for this interface. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): dev <devname> del Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Remove this virtual interface Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): dev <devname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*] [addr <mac-addr>] Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): phy <phyname> interface add <name> type <type> [mesh_id <meshid>] [4addr on|off] [flags <flag>*] [addr <mac-addr>] Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Add a new virtual interface with the given configuration. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Valid interface types are: managed, ibss, monitor, mesh, wds. Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): The flags are only used for monitor interfaces, valid flags are: Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): none: no special flags Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): fcsfail: show frames with FCS errors Sun Dec 29 02:03:37 2019 daemon.notice netifd: radio2 (20122): control: show control frames Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): otherbss: show frames from other BSSes Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): cook: use cooked mode Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): active: use active mode (ACK incoming unicast packets) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): mumimo-groupid <GROUP_ID>: use MUMIMO according to a group id Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): mumimo-follow-mac <MAC_ADDRESS>: use MUMIMO according to a MAC address Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): The mesh_id is used only for mesh mode. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> ibss join <SSID> <freq in MHz> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] [fixed-freq] [<fixed bssid>] [beacon-interval <TU>] [basic-rates <rate in Mbps,rate2,...>] [mcast-rate <rate in Mbps>] [key d:0:abcde] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Join the IBSS cell with the given SSID, if it doesn't exist create Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): it on the given frequency. When fixed frequency is requested, don't Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): join/create a cell on a different frequency. When a fixed BSSID is Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): requested use that BSSID and do not adopt another cell's BSSID even Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): if it has higher TSF and the same SSID. If an IBSS is created, create Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): it with the specified basic-rates, multicast-rate and beacon-interval. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> ibss leave Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Leave the current IBSS cell. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> station dump [-v] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): List all stations known, e.g. the AP on managed interfaces Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> station set <MAC address> vlan <ifindex> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set an AP VLAN for this station. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> station del <MAC address> [subtype <subtype>] [reason-code <code>] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Remove the given station entry (use with caution!) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Example subtype values: 0xA (disassociation), 0xC (deauthentication) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> station get <MAC address> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Get information for a specific station. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> survey dump Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): List all gathered channel survey data Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mesh leave Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Leave a mesh. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mesh join <mesh ID> [[freq <freq in MHz> <NOHT|HT20|HT40+|HT40-|80MHz>] [basic-rates <rate in Mbps,rate2,...>]], [mcast-rate <rate in Mbps>] [beacon-interval <time in TUs>] [dtim-period <value>] [vendor_sync on|off] [<param>=<value>]* Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Join a mesh with the given mesh ID with frequency, basic-rates, Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): mcast-rate and mesh parameters. Basic-rates are applied only if Sun Dec 29 02:03:38 2019 kern.info kernel: [ 1041.624934] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.4 Sun Dec 29 02:03:38 2019 kern.info kernel: [ 1041.630560] ath9k_htc 1-1:1.0: FW RMW support: On Sun Dec 29 02:03:38 2019 kern.debug kernel: [ 1041.635492] ath: EEPROM regdomain: 0x833a Sun Dec 29 02:03:38 2019 kern.debug kernel: [ 1041.635498] ath: EEPROM indicates we should expect a country code Sun Dec 29 02:03:38 2019 kern.debug kernel: [ 1041.635515] ath: doing EEPROM country->regdmn map search Sun Dec 29 02:03:38 2019 kern.debug kernel: [ 1041.635522] ath: country maps to regdmn code: 0x37 Sun Dec 29 02:03:38 2019 kern.debug kernel: [ 1041.635529] ath: Country alpha2 being used: GB Sun Dec 29 02:03:38 2019 kern.debug kernel: [ 1041.635533] ath: Regpair used: 0x37 Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): frequency is provided. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpath dump Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): List known mesh paths. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpath set <destination MAC address> next_hop <next hop MAC address> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set an existing mesh path's next hop. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpath new <destination MAC address> next_hop <next hop MAC address> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Create a new mesh path (instead of relying on automatic discovery). Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpath del <MAC address> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Remove the mesh path to the given node. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpath get <MAC address> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Get information on mesh path to the given node. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpp dump Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): List known mesh proxy paths. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> mpp get <MAC address> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Get information on mesh proxy path to the given node. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> scan [-u] [freq <freq>*] [duration <dur>] [ies <hex as 00:11:..>] [meshid <meshid>] [lowpri,flush,ap-force,duration-mandatory] [randomise[=<addr>/<mask>]] [ssid <ssid>*|passive] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Scan on the given frequencies and probe for the given SSIDs Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): (or wildcard if not given) unless passive scanning is requested. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): If -u is specified print unknown data in the scan results. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Specified (vendor) IEs must be well-formed. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> scan abort Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Abort ongoing scan Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> scan trigger [freq <freq>*] [duration <dur>] [ies <hex as 00:11:..>] [meshid <meshid>] [lowpri,flush,ap-force,duration-mandatory] [randomise[=<addr>/<mask>]] [ssid <ssid>*|passive] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Trigger a scan on the given frequencies with probing for the given Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): SSIDs (or wildcard if not given) unless passive scanning is requested. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Duration(in TUs), if specified, will be used to set dwell times. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> scan dump [-u] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Dump the current scan results. If -u is specified, print unknown Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): data in scan results. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): reg reload Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Reload the kernel's regulatory database. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> reg get Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Print out the devices' current regulatory domain information. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): reg get Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Print out the kernel's current regulatory domain information. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): reg set <ISO/IEC 3166-1 alpha2> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Notify the kernel about the current regulatory domain. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> auth <SSID> <bssid> <type:open|shared> <freq in MHz> [key 0:abcde d:1:6162636465] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Authenticate with the given network. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> connect [-w] <SSID> [<freq in MHz>] [<bssid>] [key 0:abcde d:1:6162636465] [mfp:req/opt/no] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Join the network with the given SSID (and frequency, BSSID). Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): With -w, wait for the connect to finish or fail. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> disconnect Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Disconnect from the current network. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> link Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Print information about the current link, if any. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set antenna_gain <antenna gain in dBm> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Specify antenna gain. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set txq limit <packets> | memory_limit <bytes> | quantum <bytes> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set TXQ parameters. The limit and memory_limit are global queue limits Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): for the whole phy. The quantum is the DRR scheduler quantum setting. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Valid values: 1 - 2**32 Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set antenna <bitmap> | all | <tx bitmap> <rx bitmap> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set a bitmap of allowed antennas to use for TX and RX. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): The driver may reject antenna configurations it cannot support. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set txpower <auto|fixed|limit> [<tx power in mBm>] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Specify transmit power level and setting type. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set txpower <auto|fixed|limit> [<tx power in mBm>] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Specify transmit power level and setting type. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set distance <auto|distance> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Enable ACK timeout estimation algorithm (dynack) or set appropriate Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): coverage class for given link distance in meters. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): To disable dynack set valid value for coverage class. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Valid values: 0 - 114750 Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set coverage <coverage class> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set coverage class (1 for every 3 usec of air propagation time). Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Valid values: 0 - 255. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set netns { <pid> | name <nsname> } Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Put this wireless device into a different network namespace: Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): <pid> - change network namespace by process id Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): <nsname> - change network namespace by name from /var/run/netns Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): or by absolute path (man ip-netns) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set retry [short <limit>] [long <limit>] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set retry limit. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set rts <rts threshold|off> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set rts threshold. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set frag <fragmentation threshold|off> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set fragmentation threshold. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set channel <channel> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set freq <freq> [NOHT|HT20|HT40+|HT40-|5MHz|10MHz|80MHz] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set freq <control freq> [5|10|20|40|80|80+80|160] [<center1_freq> [<center2_freq>]] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set frequency/channel the hardware is using, including HT Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): configuration. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> set name <new name> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Rename this wireless device. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set mcast_rate <rate in Mbps> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set the multicast bitrate. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 kern.info kernel: [ 1041.699326] ieee80211 phy56: Atheros AR9271 Rev:1 Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set noack_map <map> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set the NoAck map for the TIDs. (0x0009 = BE, 0x0006 = BK, 0x0030 = VI, 0x00C0 = VO) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set 4addr <on|off> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set interface 4addr (WDS) mode. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set type <type> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set interface type/mode. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Valid interface types are: managed, ibss, monitor, mesh, wds. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set meshid <meshid> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set monitor <flag>* Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set monitor flags. Valid flags are: Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): none: no special flags Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): fcsfail: show frames with FCS errors Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): control: show control frames Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): otherbss: show frames from other BSSes Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): cook: use cooked mode Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): active: use active mode (ACK incoming unicast packets) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): mumimo-groupid <GROUP_ID>: use MUMIMO according to a group id Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): mumimo-follow-mac <MAC_ADDRESS>: use MUMIMO according to a MAC address Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set mesh_param <param>=<value> [<param>=<value>]* Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set mesh parameter (run command without any to see available ones). Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set power_save <on|off> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Set power save state to on or off. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> set bitrates [legacy-<2.4|5> <legacy rate in Mbps>*] [ht-mcs-<2.4|5> <MCS index>*] [vht-mcs-<2.4|5> <NSS:MCSx,MCSy... | NSS:MCSx-MCSy>*] [sgi-2.4|lgi-2.4] [sgi-5|lgi-5] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sets up the specified rate masks. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Not passing any arguments would clear the existing mask (if any). Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): phy <phyname> get txq Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Get TXQ parameters. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> get mesh_param [<param>] Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Retrieve mesh parameter (run command without any to see available ones). Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): dev <devname> get power_save <param> Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Retrieve power save state. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Commands that use the netdev ('dev') can also be given the Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): 'wdev' instead to identify the device. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): You can omit the 'phy' or 'dev' if the identification is unique, Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): e.g. "iw wlan0 info" or "iw phy0 info". (Don't when scripting.) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Do NOT screenscrape this tool, we don't consider its output stable. Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): ifconfig: invalid hw-addr Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): cat: can't open '/sys/class/ieee80211/phy55/macaddress': No such file or directory Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): cat: can't open '/sys/class/ieee80211/phy55/address_mask': No such file or directory Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): ./mac80211.sh: eval: line 371: arithmetic syntax error Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): command failed: No such file or directory (-2) Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): ifconfig: invalid hw-addr Sun Dec 29 02:03:38 2019 kern.info kernel: [ 1042.161585] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready Sun Dec 29 02:03:38 2019 daemon.notice netifd: radio2 (20122): Successfully initialized wpa_supplicant Sun Dec 29 02:03:39 2019 kern.info kernel: [ 1043.462246] usb 1-1: USB disconnect, device number 56 Sun Dec 29 02:03:40 2019 kern.err kernel: [ 1043.577630] ath: phy56: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:40 2019 kern.err kernel: [ 1043.686193] ath: phy56: RX failed to go idle in 10 ms RXSM=0x2000000 Sun Dec 29 02:03:40 2019 kern.err kernel: [ 1043.796049] ath: phy56: RX failed to go idle in 10 ms RXSM=0x2000000  Link to comment Share on other sites More sharing options...
HomerJS Posted December 29, 2019 Author Share Posted December 29, 2019 Hi, i forget to give you the following information: I tried it under firmware verison 2.6.2 and the tetra factory. Best regards HomerJS Link to comment Share on other sites More sharing options...
Olaf Mufjay Posted December 29, 2019 Share Posted December 29, 2019 You have to change the wireless settings in your config. Your radio 0 is your Wlan0 your Radio1 is your Wlan1 if you plugged in the Alpha you should also have a Radio2 in the config for wlan2. There you have to make the following settings  conifg wifi-device radio2 otion type mac80211 option channel 11 option hwmode 11g option htmode HT20 config wifi-iface option device 'radio2' option ifname 'wlan2' option mode 'sta' option network 'wwan' option ssid 'yourSSID' option encryption 'psk2+ccmp' option key 'yourPassword' Remember that the channel you are forgiving must be the same as your AP. You can orient yourself by what your pineapple assigns automatically Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.