40Tons_Of_Bananas Posted December 7, 2013 Share Posted December 7, 2013 (edited) So I'm trying to setup my quadcore 955 black edition running on a M4A79T Deluxe SE board with the built in ethernet, however the latest version of proxmox won't allow me to connect to it after installing to a terabyte hard disk. I've run IFCONFIG and this is what the screen displays: Link encap: Ethernet HWaddr 00:24:8c:6e:bd:c0inet6 addr fe80:224:8cff:fe6e:bdc0/64 Scope: LinkUP BROADCAST RUNNING MULTICAST MTU: 1500 Metric:1RX Packets: 0 errors: 0 dropped: 0 overruns: 0 frame:0TX packets: 68 errors: 0 dropped: 0 overruns: 0 carrier:0collisions: 0 txqueueclcn: 1000RX bytes: 0 (0.0 B) TX bytes: 3328 (3.2KiB)Link encap: Local Loopbackinet addr:127.0.0.1 Mask: 255.0.0.0inet6 addr: ::1/128 Scope:HostUP LOOPBACK RUNNING MTU:16436 Metric:1RX packets: 40 errors:0 dropped: 0 overruns:0 frame:0TX packets: 40 errors: 0 dropped:0 overruns:0 carrier:0collisions: 0 txquelen:0RX Bytes: 3864 (3.7 KiB) TX bytes: 3864 (3.7 KiB)Link encap: UNSPEC HWAddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00inet6 addr: fe80::1/28 Scope:LinkUP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1RX packets:0 errors:0 dropped:0 overruns:0 frame:0TX packets:0 errors:0 dropped:3 overruns:0 carrier:0collisions:0 txquelen:0RX bytes:0 (0.0B) TX bytes:0 (0.0B)Link encap: Ethernet HWaddr:00:24:8c:6e:bd:c0inetaddr:192.168.1.5 Bcast:192.168.1.255 Mask: 255.255.255.0inet6 addr: fe80::224:8cff:fe6e:bdc0/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:0 errors:0 dropped:0 overruns:0 frame:0TX packets:60 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txquelen:0RX bytes(0.0B) TX Bytes:2776(2.7KiB) My primary router is set up in this configuration: Default Gateway: 96.253.86.1 DNS Server: 71.252.0.1268.238.112.12 Although I have set the gateway and DNS server during installation to 192.168.1.1 for both, and the IP address as 192.168.1.5 Do I need to reinstall and use the default gateway as shown in my router? by the way, this is a cruddy MI424WR router. YUCK! This is also as stated, hooked up directly to ethernet and appears to have a link. I try to connect to 192.168.1.5 and it actually trys to connect for about a minute and then displays the typical "The connection has timed out" page.The server at 192.168.1.5(:8006)is taking too long to respond. If it matters, I am also logged in as root while trying to connect. Edited December 7, 2013 by 40Tons_Of_Bananas Quote Link to comment Share on other sites More sharing options...
techiem2 Posted December 8, 2013 Share Posted December 8, 2013 1. I assume you are trying to connect to it from a machine on the same LAN. 2. Can you ping it? 3. Port 8006? (Note I'm running an older version of Proxmox, so I don't know if they've changed something, but this sounds like a basic network issue) Quote Link to comment Share on other sites More sharing options...
hexophrenic Posted December 9, 2013 Share Posted December 9, 2013 Also, have you checked the proxmox forums? While you might find help here, you would most certainly have a better chance there. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.