jjd Posted November 9, 2013 Share Posted November 9, 2013 I had been playing with my pineapple for a bit and all of a sudden when I started the web ui it hung when loading my installed infusions (all on sd) when I sshd in and looked at /sd it took about 4 minutes to ls. so I decided to format it from the gui, it ran for a bit then said done. However if I look at /sd in ssh the card has not been formatted (although ls was instant this time), all infusions were still there... just as a test I created a new dir and formatted again sure enough the new dir was still there... so I manually deleted everything on the sd and re installed my infusions. about an hour latter it happened again... so I decided dead sd (brand new out of the box today) so I installed a 2nd new 32gb sd card (I have 3 all new) but again after a few hours the sd started to hang. and again format did not format the sd... so I tried another new one... I could believe I got 1 in 3 dead 32gb cards but 3 in 3? I have now been running an 8gb card for a few hours and so far no issues (fingers crossed) any one have any ideas? oh also two of three 32gb sd cards were Patriot one was Kingston & the 8gb is Patriot. Quote Link to comment Share on other sites More sharing options...
Sailor Posted November 9, 2013 Share Posted November 9, 2013 I have experienced this once in a while and noticed the following in my log: Pineapple kern.info kernel: [75367.090000] usb 1-1.4: reset high-speed USB device number 4 using ehci-platform Did you see this as well? Quote Link to comment Share on other sites More sharing options...
jjd Posted November 10, 2013 Author Share Posted November 10, 2013 not sure I reset, I will put the 32 back in tonight and look for it Quote Link to comment Share on other sites More sharing options...
thesugarat Posted November 10, 2013 Share Posted November 10, 2013 I've seen my sd installed infusions not load also. I usually pop the sad card out while it's running and pop it back in then reboot. Quote Link to comment Share on other sites More sharing options...
mw3demo Posted March 10, 2014 Share Posted March 10, 2014 (edited) I have experienced this once in a while and noticed the following in my log: Pineapple kern.info kernel: [75367.090000] usb 1-1.4: reset high-speed USB device number 4 using ehci-platform Did you see this as well? Yes I do. Post your lsusb -v with spoiler tags. root@Pineapple:~# lsusb -v Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0002 2.0 root hub bcdDevice 3.03 iManufacturer 3 Linux 3.3.8 ehci_hcd iProduct 2 Generic Platform EHCI Controller iSerial 1 ehci-platform bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 1 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0503 highspeed power enable connect Device Status: 0x0001 Self Powered Bus 001 Device 002: ID 058f:6254 Alcor Micro Corp. USB Hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 idVendor 0x058f Alcor Micro Corp. idProduct 0x6254 USB Hub bcdDevice 1.00 iManufacturer 0 iProduct 1 USB2.0Hub iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0001 1x 1 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0080 Ganged power switching Ganged overcurrent protection TT think time 8 FS bits Port indicators bPwrOn2PwrGood 50 * 2 milli seconds bHubContrCurrent 100 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0503 highspeed power enable connect Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0503 highspeed power enable connect Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0bda Realtek Semiconductor Corp. idProduct 0x8187 RTL8187 Wireless Adapter bcdDevice 1.00 iManufacturer 1 Manufacturer_Realtek_RTL8187_ iProduct 2 RTL8187_Wireless iSerial 3 001337XXXXXX bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 39 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 4 Wireless Network Card bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 0 (Defined at Interface level) bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 5 Bulk-IN,Bulk-OUT,Bulk-OUT Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Bus 001 Device 004: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x058f Alcor Micro Corp. idProduct 0x6366 Multi Flash Reader bcdDevice 1.00 iManufacturer 1 iProduct 2 iSerial 3 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk-Only iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Status: 0x0000 (Bus Powered) . Are all these resets due to power issue? I am using the pineapple juice Edited March 10, 2014 by mw3demo Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.