Jump to content

MkIV USB Port Issue

Dread Metro

By Dread Metro
in WiFi Pineapple Mark IV

 Share

Recommended Posts

Dread Metro Newbie

Dread Metro

Posted
Posted (edited)

Hello all,

I received my MkIV a couple of weeks back... at first everything seemed to be going swimmingly. I upgraded it to 2.7.0 and used it without issues until today--the first time I tried using the USB port for anything. Whenever anything is plugged into it, the pineapple reboots and the WPS button will continuously flash. If I attempt to boot the pineapple with something plugged into the USB, the same thing happens.

I figured that this may be due to insufficient power with the USB power cord, so I tried the 12V adapter and have had the same issues. I also got my meter out and checked just to make sure both adapters were functioning properly. When that did not solve my problem, I used the reset button and re-flashed 2.7.0 but the problem persists. This is happening with several different thumb drives and two different Alfa cards.

Here's everything in my system log since the reset (I made it fail once since that reset as well)


02:46:59 Pineapple cron.err crond[1359]: time disparity of 22547685 minutes detected
00:01:13 Pineapple user.info sysinit: sh: write error: Invalid argument
00:01:13 Pineapple user.info sysinit: sh: write error: Invalid argument
00:01:13 Pineapple user.info sysinit: setting up led WLAN
00:01:13 Pineapple user.info sysinit: setting up led WAN
00:01:13 Pineapple user.info sysinit: setting up led USB
00:01:13 Pineapple user.info sysinit: setting up led LAN
00:01:13 Pineapple user.info sysinit: Selected interface 'wlan0'
00:01:13 Pineapple user.info sysinit: OK
00:01:13 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:wan/mode: nonexistent directory
00:01:13 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:wan/device_name: nonexistent directory
00:01:13 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:lan/mode: nonexistent directory
00:01:13 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:lan/device_name: nonexistent directory
00:01:12 Pineapple kern.info kernel: [ 72.770000] br-lan: port 2(wlan0) entered forwarding state
00:01:10 Pineapple kern.info kernel: [ 70.770000] br-lan: port 2(wlan0) entered forwarding state
00:01:10 Pineapple kern.info kernel: [ 70.760000] br-lan: port 2(wlan0) entered forwarding state
00:01:10 Pineapple kern.info kernel: [ 70.690000] device wlan0 entered promiscuous mode
00:01:09 Pineapple kern.info kernel: [ 69.940000] device wlan0 left promiscuous mode
00:01:09 Pineapple kern.info kernel: [ 69.940000] br-lan: port 2(wlan0) entered disabled state
00:01:09 Pineapple daemon.info dnsmasq[1435]: using nameserver 8.8.8.8#53
00:01:09 Pineapple daemon.info dnsmasq[1435]: using local addresses only for domain lan
00:01:09 Pineapple daemon.info dnsmasq[1435]: using local addresses only for domain lan
00:01:09 Pineapple daemon.info dnsmasq[1435]: started, version 2.62 cachesize 150
00:01:09 Pineapple daemon.info dnsmasq[1435]: reading /tmp/resolv.conf.auto
00:01:09 Pineapple daemon.info dnsmasq[1435]: read /etc/hosts - 1 addresses
00:01:09 Pineapple daemon.info dnsmasq[1435]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
00:01:09 Pineapple daemon.info dnsmasq-dhcp[1435]: read /etc/ethers - 0 addresses
00:01:09 Pineapple daemon.info dnsmasq-dhcp[1435]: DHCP, IP range 172.16.42.100 -- 172.16.42.249, lease time 12h
00:01:06 Pineapple user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
00:01:06 Pineapple user.notice dnsmasq: Allowing 127.0.0.0/8 responses
00:01:04 Pineapple user.err autossh[1120]: ssh exited prematurely with status 1; autossh exiting
00:01:03 Pineapple daemon.notice netifd: wan (1089): Sending discover...
00:01:03 Pineapple cron.info crond[1359]: crond: crond (busybox 1.19.4) started, log level 5
00:01:03 Pineapple authpriv.info dropbear[1376]: Running in background
00:01:02 Pineapple kern.info kernel: [ 62.670000] br-lan: port 2(wlan0) entered forwarding state
00:01:00 Pineapple kern.info kernel: [ 60.670000] br-lan: port 2(wlan0) entered forwarding state
00:01:00 Pineapple kern.info kernel: [ 60.660000] br-lan: port 2(wlan0) entered forwarding state
00:01:00 Pineapple kern.info kernel: [ 60.590000] device wlan0 entered promiscuous mode
00:01:00 Pineapple kern.info kernel: [ 60.510000] br-lan: port 1(eth0) entered forwarding state
00:01:00 Pineapple daemon.notice netifd: wan (1089): Sending discover...
00:00:59 Pineapple user.notice ifup: Enabling Router Solicitations on loopback (lo)
00:00:58 Pineapple user.notice ifup: Enabling Router Solicitations on lan (br-lan)
00:00:58 Pineapple user.info autossh[1120]: starting ssh (count 1)
00:00:58 Pineapple user.info autossh[1120]: ssh child pid is 1122
00:00:58 Pineapple kern.info kernel: [ 58.510000] br-lan: port 1(eth0) entered forwarding state
00:00:58 Pineapple kern.info kernel: [ 58.510000] br-lan: port 1(eth0) entered forwarding state
00:00:58 Pineapple kern.info kernel: [ 58.450000] eth0: link up (1000Mbps/Full duplex)
00:00:57 Pineapple kern.info kernel: [ 57.300000] device eth0 entered promiscuous mode
00:00:57 Pineapple daemon.notice netifd: wan (1089): udhcpc (v1.19.4) started
00:00:57 Pineapple daemon.notice netifd: wan (1089): Sending discover...
00:00:57 Pineapple daemon.notice netifd: Interface 'loopback' is now up
00:00:57 Pineapple daemon.notice netifd: Interface 'lan' is now up
00:00:41 Pineapple user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Zone PFN ranges:
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Movable zone start PFN for each node
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Early memory PFN ranges
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
00:00:39 Pineapple kern.warn kernel: [ 0.000000] Normal 0x00000000 -> 0x00002000
00:00:39 Pineapple kern.warn kernel: [ 0.000000] 0: 0x00000000 -> 0x00002000
00:00:39 Pineapple kern.notice kernel: [ 0.000000] Kernel command line: board=HORNET-UB console=ttyATH0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6144k(rootfs),1600k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noi
00:00:39 Pineapple kern.info kernel: [ 37.240000] usbcore: registered new interface driver cdc_ether
00:00:39 Pineapple kern.info kernel: [ 37.200000] usbserial: USB Serial Driver core
00:00:39 Pineapple kern.info kernel: [ 37.190000] usbcore: registered new interface driver usbserial_generic
00:00:39 Pineapple kern.info kernel: [ 37.190000] USB Serial support registered for generic
00:00:39 Pineapple kern.info kernel: [ 37.180000] usbcore: registered new interface driver usbserial
00:00:39 Pineapple kern.info kernel: [ 36.930000] usbcore: registered new interface driver ath9k_htc
00:00:39 Pineapple kern.info kernel: [ 36.120000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
00:00:39 Pineapple kern.info kernel: [ 35.990000] NET: Registered protocol family 24
00:00:39 Pineapple kern.info kernel: [ 35.770000] ip_tables: (C) 2000-2006 Netfilter Core Team
00:00:39 Pineapple kern.info kernel: [ 35.500000] tun: Universal TUN/TAP device driver, 1.6
00:00:39 Pineapple kern.info kernel: [ 35.500000] tun: (C) 1999-2004 Max Krasnyansky
00:00:39 Pineapple kern.info kernel: [ 35.360000] PPP generic driver version 2.4.2
00:00:39 Pineapple kern.info kernel: [ 35.010000] RPC: Registered tcp transport module.
00:00:39 Pineapple kern.info kernel: [ 35.010000] RPC: Registered tcp NFSv4.1 backchannel transport module.
00:00:39 Pineapple kern.info kernel: [ 35.000000] RPC: Registered udp transport module.
00:00:39 Pineapple kern.info kernel: [ 35.000000] RPC: Registered named UNIX socket transport module.
00:00:39 Pineapple kern.info kernel: [ 34.760000] Button Hotplug driver version 0.4.1
00:00:39 Pineapple kern.info kernel: [ 34.750000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
00:00:39 Pineapple kern.info kernel: [ 34.740000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 34.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 34.730000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 34.720000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
00:00:39 Pineapple kern.info kernel: [ 34.710000] cfg80211: Regulatory domain changed to country: GB
00:00:39 Pineapple kern.info kernel: [ 34.710000] cfg80211: Calling CRDA for country: GB
00:00:39 Pineapple kern.info kernel: [ 34.630000] usbcore: registered new interface driver rt2800usb
00:00:39 Pineapple kern.info kernel: [ 34.610000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
00:00:39 Pineapple kern.info kernel: [ 34.570000] usbcore: registered new interface driver rtl8187
00:00:39 Pineapple kern.info kernel: [ 34.420000] usbcore: registered new interface driver rt73usb
00:00:39 Pineapple kern.info kernel: [ 33.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.790000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.790000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.770000] cfg80211: World regulatory domain updated:
00:00:39 Pineapple kern.info kernel: [ 33.770000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
00:00:39 Pineapple kern.info kernel: [ 33.100000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.090000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.090000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.080000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:39 Pineapple kern.info kernel: [ 33.060000] cfg80211: World regulatory domain updated:
00:00:39 Pineapple kern.info kernel: [ 33.060000] cfg80211: Calling CRDA to update world regulatory domain
00:00:39 Pineapple kern.info kernel: [ 33.060000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
00:00:39 Pineapple kern.info kernel: [ 32.950000] compat.git: wireless-testing.git
00:00:39 Pineapple kern.info kernel: [ 32.950000] Backport based on wireless-testing.git master-2012-07-16
00:00:39 Pineapple kern.info kernel: [ 32.940000] Compat-wireless backport release: compat-wireless-2012-07-13
00:00:39 Pineapple kern.info kernel: [ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.590000] NET: Registered protocol family 1
00:00:39 Pineapple kern.info kernel: [ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.580000] TCP reno registered
00:00:39 Pineapple kern.info kernel: [ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)
00:00:39 Pineapple kern.info kernel: [ 0.560000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.560000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.560000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.550000] Switching to clocksource MIPS
00:00:39 Pineapple kern.info kernel: [ 0.550000] NET: Registered protocol family 2
00:00:39 Pineapple kern.info kernel: [ 0.540000] bio: create slab at 0
00:00:39 Pineapple kern.info kernel: [ 0.100000] MIPS: machine is ALFA NETWORKS Hornet-UB
00:00:39 Pineapple kern.info kernel: [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
00:00:39 Pineapple kern.info kernel: [ 0.090000] NET: Registered protocol family 16
00:00:39 Pineapple kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
00:00:39 Pineapple kern.info kernel: [ 0.080000] Mount-cache hash table entries: 512
00:00:39 Pineapple kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
00:00:39 Pineapple kern.info kernel: [ 0.000000] SoC: Atheros AR9330 rev 1
00:00:39 Pineapple kern.info kernel: [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
00:00:39 Pineapple kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
00:00:39 Pineapple kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.000000] NR_IRQS:51
00:00:39 Pineapple kern.info kernel: [ 0.000000] Memory: 29276k/32768k available (2082k kernel code, 3492k reserved, 396k data, 204k init, 0k highmem)
00:00:39 Pineapple kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd
00:00:39 Pineapple kern.info kernel: [ 0.000000] Determined physical RAM map:
00:00:39 Pineapple kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
00:00:39 Pineapple kern.info kernel: [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
00:00:39 Pineapple kern.info kernel: [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
00:00:39 Pineapple kern.info kernel: [ 0.000000] memory: 02000000 @ 00000000 (usable)
00:00:39 Pineapple kern.debug kernel: [ 34.610000] Registered led device: ath9k-phy0
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ath: doing EEPROM country->regdmn map search
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ath: country maps to regdmn code: 0x37
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ath: Regpair used: 0x37
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ath: EEPROM regdomain: 0x833a
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ath: EEPROM indicates we should expect a country code
00:00:39 Pineapple kern.debug kernel: [ 34.600000] ath: Country alpha2 being used: GB
00:00:39 Pineapple kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
00:00:39 Pineapple kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0
00:00:39 Pineapple kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 802cb680, node_mem_map 81000000
00:00:39 Pineapple kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192
00:00:39 Pineapple kern.debug kernel: [ 0.000000] Normal zone: 8128 pages, LIFO batch:0
00:00:39 Pineapple kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap
00:00:39 Pineapple kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved
[/CODE]

Anyone have any ideas? I haven't been able to find much on this.

Edited by Mr-Protocol
  • 2 weeks later...
SpeedBomb Newbie

SpeedBomb

Posted
Posted (edited)

Hello All,

I'd like to add to this topic and say that i've been having the same issue my mark iv reboots when i connect a usb flash drive and the wps just keeps flashing.

I did try the down grade too 2.6.4 and 2.6.3 but both of them did the same thing.

Any ideas on how I can solve this issue?

Info:

Pineapple Hardware Version Mark IV

Pineapple Software Version 2.6.3, 2.6.4, 2.7.0

Windows 7 & through firefox or putty to connect to pineapple

Lan cable

Standard out the box install, nothing added yet cause i can't get my usb too work.

Ping results from computer to pineapple:

Pinging 172.16.42.1 with 32 bytes of data:

Reply from 172.16.42.1: bytes=32 time<1ms TTL=64

Reply from 172.16.42.1: bytes=32 time=1ms TTL=64

Reply from 172.16.42.1: bytes=32 time<1ms TTL=64

Reply from 172.16.42.1: bytes=32 time<1ms TTL=64

Ping statistics for 172.16.42.1:

Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),

Approximate round trip times in milli-seconds:

Minimum = 0ms, Maximum = 1ms, Average = 0ms

Is the problem repeatable: Yes

Steps taken which created the problem: Plug in usb drive

Below is my system log:

00:01:12 Pineapple user.info sysinit: sh: write error: Invalid argument

00:01:12 Pineapple user.info sysinit: sh: write error: Invalid argument

00:01:12 Pineapple user.info sysinit: setting up led WLAN

00:01:12 Pineapple user.info sysinit: setting up led WAN

00:01:12 Pineapple user.info sysinit: setting up led USB

00:01:12 Pineapple user.info sysinit: setting up led LAN

00:01:12 Pineapple user.info sysinit: Selected interface 'wlan0'

00:01:12 Pineapple user.info sysinit: OK

00:01:12 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:wan/mode: nonexistent directory

00:01:12 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:wan/device_name: nonexistent directory

00:01:12 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:lan/mode: nonexistent directory

00:01:12 Pineapple user.info sysinit: /etc/rc.common: eval: line 1: can't create /sys/class/leds/alfa:blue:lan/device_name: nonexistent directory

00:01:11 Pineapple kern.info kernel: [ 71.570000] br-lan: port 2(wlan0) entered forwarding state

00:01:09 Pineapple kern.info kernel: [ 69.570000] br-lan: port 2(wlan0) entered forwarding state

00:01:09 Pineapple kern.info kernel: [ 69.570000] br-lan: port 2(wlan0) entered forwarding state

00:01:09 Pineapple kern.info kernel: [ 69.490000] device wlan0 entered promiscuous mode

00:01:08 Pineapple kern.info kernel: [ 68.750000] device wlan0 left promiscuous mode

00:01:08 Pineapple kern.info kernel: [ 68.750000] br-lan: port 2(wlan0) entered disabled state

00:01:08 Pineapple daemon.info dnsmasq[1502]: using nameserver 8.8.8.8#53

00:01:08 Pineapple daemon.info dnsmasq[1502]: using nameserver 192.168.10.1#53

00:01:08 Pineapple daemon.info dnsmasq[1502]: using local addresses only for domain lan

00:01:08 Pineapple daemon.info dnsmasq[1502]: using local addresses only for domain lan

00:01:08 Pineapple daemon.info dnsmasq[1502]: started, version 2.62 cachesize 150

00:01:08 Pineapple daemon.info dnsmasq[1502]: reading /tmp/resolv.conf.auto

00:01:08 Pineapple daemon.info dnsmasq[1502]: read /etc/hosts - 1 addresses

00:01:08 Pineapple daemon.info dnsmasq[1502]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack

00:01:08 Pineapple daemon.info dnsmasq-dhcp[1502]: read /etc/ethers - 0 addresses

00:01:08 Pineapple daemon.info dnsmasq-dhcp[1502]: DHCP, IP range 172.16.42.100 -- 172.16.42.249, lease time 12h

00:01:05 Pineapple user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!

00:01:05 Pineapple user.notice dnsmasq: Allowing 127.0.0.0/8 responses

00:01:04 Pineapple user.err autossh[1153]: ssh exited prematurely with status 1; autossh exiting

00:01:03 Pineapple cron.info crond[1432]: crond: crond (busybox 1.19.4) started, log level 5

00:01:03 Pineapple authpriv.info dropbear[1449]: Running in background

00:01:02 Pineapple kern.info kernel: [ 62.550000] br-lan: port 2(wlan0) entered forwarding state

00:01:01 Pineapple user.notice ifup: Allowing Router Advertisements on wan (eth1)

00:01:01 Pineapple daemon.notice netifd: wan (1124): Sending select for 192.168.10.22...

00:01:01 Pineapple daemon.notice netifd: wan (1124): Lease of 192.168.10.22 obtained, lease time 86400

00:01:01 Pineapple daemon.notice netifd: Interface 'wan' is now up

00:01:00 Pineapple kern.info kernel: [ 60.550000] br-lan: port 2(wlan0) entered forwarding state

00:01:00 Pineapple kern.info kernel: [ 60.550000] br-lan: port 2(wlan0) entered forwarding state

00:01:00 Pineapple kern.info kernel: [ 60.470000] device wlan0 entered promiscuous mode

00:01:00 Pineapple daemon.notice netifd: wan (1124): Sending discover...

00:00:59 Pineapple user.notice ifup: Enabling Router Solicitations on loopback (lo)

00:00:59 Pineapple kern.info kernel: [ 59.900000] br-lan: port 1(eth0) entered forwarding state

00:00:59 Pineapple kern.info kernel: [ 59.410000] eth1: link up (100Mbps/Full duplex)

00:00:58 Pineapple user.notice ifup: Enabling Router Solicitations on lan (br-lan)

00:00:58 Pineapple user.info autossh[1153]: starting ssh (count 1)

00:00:58 Pineapple user.info autossh[1153]: ssh child pid is 1154

00:00:57 Pineapple kern.info kernel: [ 57.900000] eth0: link up (1000Mbps/Full duplex)

00:00:57 Pineapple kern.info kernel: [ 57.900000] br-lan: port 1(eth0) entered forwarding state

00:00:57 Pineapple kern.info kernel: [ 57.900000] br-lan: port 1(eth0) entered forwarding state

00:00:57 Pineapple kern.info kernel: [ 57.230000] device eth0 entered promiscuous mode

00:00:57 Pineapple daemon.notice netifd: wan (1124): udhcpc (v1.19.4) started

00:00:57 Pineapple daemon.notice netifd: wan (1124): Sending discover...

00:00:57 Pineapple daemon.notice netifd: Interface 'loopback' is now up

00:00:57 Pineapple daemon.notice netifd: Interface 'lan' is now up

00:00:41 Pineapple user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Zone PFN ranges:

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Movable zone start PFN for each node

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Early memory PFN ranges

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128

00:00:39 Pineapple kern.warn kernel: [ 0.000000] Normal 0x00000000 -> 0x00002000

00:00:39 Pineapple kern.warn kernel: [ 0.000000] 0: 0x00000000 -> 0x00002000

00:00:39 Pineapple kern.notice kernel: [ 0.000000] Kernel command line: board=HORNET-UB console=ttyATH0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6144k(rootfs),1600k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noi

00:00:39 Pineapple kern.info kernel: [ 37.250000] usbcore: registered new interface driver usbserial

00:00:39 Pineapple kern.info kernel: [ 37.010000] usbcore: registered new interface driver ath9k_htc

00:00:39 Pineapple kern.info kernel: [ 36.160000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)

00:00:39 Pineapple kern.info kernel: [ 36.030000] NET: Registered protocol family 24

00:00:39 Pineapple kern.info kernel: [ 35.810000] ip_tables: © 2000-2006 Netfilter Core Team

00:00:39 Pineapple kern.info kernel: [ 35.550000] PPP generic driver version 2.4.2

00:00:39 Pineapple kern.info kernel: [ 35.200000] RPC: Registered tcp NFSv4.1 backchannel transport module.

00:00:39 Pineapple kern.info kernel: [ 35.190000] RPC: Registered udp transport module.

00:00:39 Pineapple kern.info kernel: [ 35.190000] RPC: Registered tcp transport module.

00:00:39 Pineapple kern.info kernel: [ 35.190000] RPC: Registered named UNIX socket transport module.

00:00:39 Pineapple kern.info kernel: [ 34.960000] Button Hotplug driver version 0.4.1

00:00:39 Pineapple kern.info kernel: [ 34.940000] usbcore: registered new interface driver rt2800usb

00:00:39 Pineapple kern.info kernel: [ 34.910000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)

00:00:39 Pineapple kern.info kernel: [ 34.910000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 34.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 34.890000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 34.880000] cfg80211: Regulatory domain changed to country: GB

00:00:39 Pineapple kern.info kernel: [ 34.880000] cfg80211: Calling CRDA for country: GB

00:00:39 Pineapple kern.info kernel: [ 34.880000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

00:00:39 Pineapple kern.info kernel: [ 34.770000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2

00:00:39 Pineapple kern.info kernel: [ 34.730000] usbcore: registered new interface driver rtl8187

00:00:39 Pineapple kern.info kernel: [ 34.590000] usbcore: registered new interface driver rt73usb

00:00:39 Pineapple kern.info kernel: [ 33.830000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.830000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.820000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.810000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.800000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

00:00:39 Pineapple kern.info kernel: [ 33.790000] cfg80211: World regulatory domain updated:

00:00:39 Pineapple kern.info kernel: [ 33.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.190000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.190000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.180000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.170000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

00:00:39 Pineapple kern.info kernel: [ 33.160000] cfg80211: World regulatory domain updated:

00:00:39 Pineapple kern.info kernel: [ 33.160000] cfg80211: Calling CRDA to update world regulatory domain

00:00:39 Pineapple kern.info kernel: [ 33.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

00:00:39 Pineapple kern.info kernel: [ 33.060000] compat.git: wireless-testing.git

00:00:39 Pineapple kern.info kernel: [ 33.050000] Compat-wireless backport release: compat-wireless-2012-07-13

00:00:39 Pineapple kern.info kernel: [ 33.050000] Backport based on wireless-testing.git master-2012-07-16

00:00:39 Pineapple kern.info kernel: [ 32.220000] eth0: link down

00:00:39 Pineapple kern.info kernel: [ 11.660000] usbcore: registered new interface driver usb-storage

00:00:39 Pineapple kern.info kernel: [ 11.660000] USB Mass Storage support registered.

00:00:39 Pineapple kern.info kernel: [ 11.650000] Initializing USB Mass Storage driver...

00:00:39 Pineapple kern.info kernel: [ 11.540000] uhci_hcd: USB Universal Host Controller Interface driver

00:00:39 Pineapple kern.info kernel: [ 11.420000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

00:00:39 Pineapple kern.info kernel: [ 11.410000] eth0: link up (1000Mbps/Full duplex)

00:00:39 Pineapple kern.info kernel: [ 11.290000] hub 1-0:1.0: USB hub found

00:00:39 Pineapple kern.info kernel: [ 11.290000] hub 1-0:1.0: 1 port detected

00:00:39 Pineapple kern.info kernel: [ 0.560000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)

00:00:39 Pineapple kern.info kernel: [ 0.560000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

00:00:39 Pineapple kern.info kernel: [ 0.550000] Switching to clocksource MIPS

00:00:39 Pineapple kern.info kernel: [ 0.550000] NET: Registered protocol family 2

00:00:39 Pineapple kern.info kernel: [ 0.540000] bio: create slab at 0

00:00:39 Pineapple kern.info kernel: [ 0.100000] MIPS: machine is ALFA NETWORKS Hornet-UB

00:00:39 Pineapple kern.info kernel: [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79

00:00:39 Pineapple kern.info kernel: [ 0.090000] NET: Registered protocol family 16

00:00:39 Pineapple kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301

00:00:39 Pineapple kern.info kernel: [ 0.080000] Mount-cache hash table entries: 512

00:00:39 Pineapple kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000

00:00:39 Pineapple kern.info kernel: [ 0.000000] SoC: Atheros AR9330 rev 1

00:00:39 Pineapple kern.info kernel: [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

00:00:39 Pineapple kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000

00:00:39 Pineapple kern.info kernel: [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)

00:00:39 Pineapple kern.info kernel: [ 0.000000] NR_IRQS:51

00:00:39 Pineapple kern.info kernel: [ 0.000000] Memory: 29276k/32768k available (2082k kernel code, 3492k reserved, 396k data, 204k init, 0k highmem)

00:00:39 Pineapple kern.info kernel: [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

00:00:39 Pineapple kern.info kernel: [ 0.000000] Initrd not found or empty - disabling initrd

00:00:39 Pineapple kern.info kernel: [ 0.000000] Determined physical RAM map:

00:00:39 Pineapple kern.info kernel: [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

00:00:39 Pineapple kern.info kernel: [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz

00:00:39 Pineapple kern.info kernel: [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)

00:00:39 Pineapple kern.info kernel: [ 0.000000] memory: 02000000 @ 00000000 (usable)

00:00:39 Pineapple kern.debug kernel: [ 34.770000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

00:00:39 Pineapple kern.debug kernel: [ 34.770000] Registered led device: ath9k-phy0

00:00:39 Pineapple kern.debug kernel: [ 34.760000] ath: doing EEPROM country->regdmn map search

00:00:39 Pineapple kern.debug kernel: [ 34.760000] ath: country maps to regdmn code: 0x37

00:00:39 Pineapple kern.debug kernel: [ 34.760000] ath: Regpair used: 0x37

00:00:39 Pineapple kern.debug kernel: [ 34.760000] ath: EEPROM regdomain: 0x833a

00:00:39 Pineapple kern.debug kernel: [ 34.760000] ath: EEPROM indicates we should expect a country code

00:00:39 Pineapple kern.debug kernel: [ 34.760000] ath: Country alpha2 being used: GB

00:00:39 Pineapple kern.debug kernel: [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768

00:00:39 Pineapple kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0

00:00:39 Pineapple kern.debug kernel: [ 0.000000] free_area_init_node: node 0, pgdat 802cb680, node_mem_map 81000000

00:00:39 Pineapple kern.debug kernel: [ 0.000000] On node 0 totalpages: 8192

00:00:39 Pineapple kern.debug kernel: [ 0.000000] Normal zone: 8128 pages, LIFO batch:0

00:00:39 Pineapple kern.debug kernel: [ 0.000000] Normal zone: 64 pages used for memmap

Edited by Mr-Protocol
  • 3 weeks later...
  • 1 month later...
piffdos Newbie

piffdos

Posted
Posted

I am going to try installing the 2.7.1 firmware and see if that improves the issue. the update states

"-Improved USB reliability

  • USB drives should mount more reliably now.
  • USB Wifi cards should be better recognized and should always enable on boot (Tested with ALFA NHA)."
piffdos Newbie

piffdos

Posted
Posted

you might want to try updating to the 2.7.4 firmware as doing so solved the same reboot / lockup problem that I was having, although I was not using a USB hub, just a flash drive.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...