Marcus Dempsey Posted July 15, 2017 Share Posted July 15, 2017 Hi, Just upgraded to a Nano, however after configuring it via wp.sh I'm getting the message 'Network is unreachable' when trying to do anything, I'm unable to access anything. If I disconnect the nano my network comes back fully. My routing table before WifiPineapple: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gateway 0.0.0.0 UG 100 0 0 eth0 172.16.161.0 0.0.0.0 255.255.255.0 U 100 0 0 eth0 My routing table once nano is connected: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.42.0 0.0.0.0 255.255.255.0 U 100 0 0 eth1 172.16.161.0 0.0.0.0 255.255.255.0 U 100 0 0 eth0 I'm connected to my Kali instance in a VMWare VM. Any ideas? Marcus Quote Link to comment Share on other sites More sharing options...
Decoy Posted July 15, 2017 Share Posted July 15, 2017 20 minutes ago, Marcus Dempsey said: Hi, Just upgraded to a Nano, however after configuring it via wp.sh I'm getting the message 'Network is unreachable' when trying to do anything, I'm unable to access anything. If I disconnect the nano my network comes back fully. My routing table before WifiPineapple: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gateway 0.0.0.0 UG 100 0 0 eth0 172.16.161.0 0.0.0.0 255.255.255.0 U 100 0 0 eth0 My routing table once nano is connected: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.42.0 0.0.0.0 255.255.255.0 U 100 0 0 eth1 172.16.161.0 0.0.0.0 255.255.255.0 U 100 0 0 eth0 I'm connected to my Kali instance in a VMWare VM. Any ideas? Marcus The nano uses wp6.sh, have you downloaded the latest version from GitHub? Quote Link to comment Share on other sites More sharing options...
Decoy Posted July 15, 2017 Share Posted July 15, 2017 Also, there have been times where I had to configure manually with wp6.sh, and I had to reconnect to wifi after if I wasn't connected over Ethernet. This only happened with ParrotOS for me. Kali and Ubuntu worked with Guided setup perfectly. Quote Link to comment Share on other sites More sharing options...
Marcus Dempsey Posted July 15, 2017 Author Share Posted July 15, 2017 Hi, Yeah also confirmed the codebase from: https://github.com/hak5darren/wp6/blob/master/wp6.sh, had a few goes, with no joy yet. Just wanted to see whether this was a known issue or not, as didnt have the issue with the pineapple mark V. Marcus Quote Link to comment Share on other sites More sharing options...
Decoy Posted July 15, 2017 Share Posted July 15, 2017 Are you connected over WiFi or Ethernet? Have you tried both manual and Guided setup? I found I had to wait until the LED was solid and the Pineapple was fully booted before sharing internet. Over WiFi, I had to reconnect to the Wifi access point after sharing internet when using Parrot. 1 Quote Link to comment Share on other sites More sharing options...
Decoy Posted July 15, 2017 Share Posted July 15, 2017 How are you sharing internet with the VM? Have you tried it in client mode or outside of the VM? Quote Link to comment Share on other sites More sharing options...
Marcus Dempsey Posted July 15, 2017 Author Share Posted July 15, 2017 Ah, you got it in one, had to restart eth0, and it all works fine. thanks for your help. Marcus 1 Quote Link to comment Share on other sites More sharing options...
Decoy Posted July 15, 2017 Share Posted July 15, 2017 6 minutes ago, Marcus Dempsey said: Ah, you got it in one, had to restart eth0, and it all works fine. thanks for your help. Marcus Awesome. Enjoy the Nano. Quote Link to comment Share on other sites More sharing options...
Marcus Dempsey Posted July 15, 2017 Author Share Posted July 15, 2017 Thanks will do, looking much smoother and easier to play with than the mark V Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.