segarrra Posted July 8, 2013 Posted July 8, 2013 Hi, We just bought a WiFi Pineapple Mark IV and we are not able to configure a ZTE MF110 with Movistar (Spain). We are using version 2.8.1 and this is our information: lsusb output Bus 001 Device 005: ID 19d2:0124 ZTE WCDMA Technologies MSM Switch case *19d2:0124*) echo "ZTE MF110 (Movistar) detected. Attempting mode switch" uci delete network.wan2 uci set network.wan2=interface uci set network.wan2.ifname=ppp0 uci set network.wan2.proto=3g uci set network.wan2.service=umts uci set network.wan2.device=/dev/ttyUSB1 uci set network.wan2.apn=movistar.es uci set network.wan2.username=MOVISTAR uci set network.wan2.password=MOVISTAR uci set network.wan2.defaultroute=1 uci commit network # There is no need to use the usb_modeswitch command because the kernel does the switching alone for ZTE USB sticks #usb_modeswitch -v 19d2 -p 0124 -V 19d2 -P 0124 -M 5553424312345678000000000000061b000000020000000000000000000000 -n 1 -s 20 #usb_modeswitch -v 19d2 -p 0124 sleep 10; rmmod usbserial sleep 3; insmod usbserial vendor=0x19d2 product=0x0124 # Firewall is not needed anymore #sleep 5; /etc/init.d/firewall disable; /etc/init.d/firewall stop #logger "3G: firewall stopped" iptables -t nat -A POSTROUTING -s 172.16.42.0/24 -o 3g-wan2 -j MASQUERADE iptables -A FORWARD -s 172.16.42.0/24 -o 3g-wan2 -j ACCEPT iptables -A FORWARD -d 172.16.42.0/24 -m state --state ESTABLISHED,RELATED -i 3g-wan2 -j ACCEPT We think that the mode switch is done correctly, because we can see the usb-serial interfaces: root@Pineapple:~# ls /dev/ttyUSB* /dev/ttyUSB0 /dev/ttyUSB1 /dev/ttyUSB2 /dev/ttyUSB3 /dev/ttyUSB4 /dev/ttyUSB5 And when executing the comgt it looks like we are registered in the net: root@Pineapple:~# comgt Trying list of devices SIM ready Waiting for Registration..(120 sec max) Registered on Home network: "movistar",2 Signal Quality: 23,99 But when booting the pineapple with the "3G bootup" activated, we can see this messages in the logs: 00:02:14 Pineapple daemon.info pppd[2305]: Exit. 00:02:13 Pineapple local2.info chat[2309]: alarm 00:02:13 Pineapple local2.info chat[2309]: Failed 00:02:13 Pineapple daemon.err pppd[2305]: Connect script failed 00:02:03 Pineapple local2.info chat[2309]: timeout set to 10 seconds 00:02:03 Pineapple local2.info chat[2309]: send (AT&F^M) 00:02:03 Pineapple local2.info chat[2309]: report (CONNECT) 00:02:03 Pineapple local2.info chat[2309]: expect (OK) 00:02:03 Pineapple local2.info chat[2309]: abort on (NO CARRIER) 00:02:03 Pineapple local2.info chat[2309]: abort on (ERROR) 00:02:03 Pineapple local2.info chat[2309]: abort on (BUSY) 00:02:02 Pineapple daemon.notice pppd[2305]: pppd 2.4.5 started by root, uid 0 00:02:02 Pineapple daemon.info dnsmasq[1808]: using nameserver 8.8.8.8#53 00:02:02 Pineapple daemon.info dnsmasq[1808]: using local addresses only for domain lan 00:02:02 Pineapple daemon.info dnsmasq[1808]: reading /tmp/resolv.conf.auto 00:02:00 Pineapple daemon.notice pppd[2237]: Modem hangup 00:02:00 Pineapple daemon.notice netifd: Interface 'wan2' is now down 00:02:00 Pineapple daemon.info pppd[2237]: Exit. 00:01:59 Pineapple daemon.warn pppd[2237]: LCP: timeout sending Config-Requests 00:01:59 Pineapple daemon.notice pppd[2237]: Connection terminated. 00:01:28 Pineapple local2.info chat[2253]: timeout set to 30 seconds 00:01:28 Pineapple local2.info chat[2253]: timeout set to 10 seconds 00:01:28 Pineapple local2.info chat[2253]: send (ATE1^M) 00:01:28 Pineapple local2.info chat[2253]: send (ATD*99***1#^M) 00:01:28 Pineapple local2.info chat[2253]: send (AT+CGDCONT=1,"IP","movistar.es"^M) 00:01:28 Pineapple local2.info chat[2253]: send (AT&F^M) 00:01:28 Pineapple local2.info chat[2253]: send ( ^M) 00:01:28 Pineapple local2.info chat[2253]: report (CONNECT) 00:01:28 Pineapple local2.info chat[2253]: expect (OK) 00:01:28 Pineapple local2.info chat[2253]: expect (OK) 00:01:28 Pineapple local2.info chat[2253]: expect (OK) 00:01:28 Pineapple local2.info chat[2253]: expect (CONNECT) 00:01:28 Pineapple local2.info chat[2253]: abort on (NO CARRIER) 00:01:28 Pineapple local2.info chat[2253]: abort on (ERROR) 00:01:28 Pineapple local2.info chat[2253]: abort on (BUSY) 00:01:28 Pineapple local2.info chat[2253]: ^M 00:01:28 Pineapple local2.info chat[2253]: ^M 00:01:28 Pineapple local2.info chat[2253]: ^M 00:01:28 Pineapple local2.info chat[2253]: OK 00:01:28 Pineapple local2.info chat[2253]: OK 00:01:28 Pineapple local2.info chat[2253]: OK 00:01:28 Pineapple local2.info chat[2253]: CONNECT 00:01:28 Pineapple local2.info chat[2253]: ATE1^M^M 00:01:28 Pineapple local2.info chat[2253]: ATD*99***1#^M^M 00:01:28 Pineapple local2.info chat[2253]: AT+CGDCONT=1,"IP","movistar.es"^M^M 00:01:28 Pineapple local2.info chat[2253]: AT&F^M^M 00:01:28 Pineapple local2.info chat[2253]: -- got it 00:01:28 Pineapple local2.info chat[2253]: -- got it 00:01:28 Pineapple local2.info chat[2253]: -- got it 00:01:28 Pineapple local2.info chat[2253]: -- got it 00:01:28 Pineapple daemon.notice pppd[2237]: Connect: 3g-wan2 <--> /dev/ttyUSB1 00:01:28 Pineapple daemon.info pppd[2237]: Using interface 3g-wan2 00:01:28 Pineapple daemon.info pppd[2237]: Serial connection established. 00:01:27 Pineapple daemon.notice pppd[2237]: pppd 2.4.5 started by root, uid 0 00:01:25 Pineapple kern.info kernel: [ 85.410000] device wlan0 left promiscuous mode 00:01:25 Pineapple kern.info kernel: [ 85.410000] br-lan: port 2(wlan0) entered disabled state 00:01:25 Pineapple kern.info kernel: [ 85.300000] br-lan: port 2(wlan0) entered disabled state 00:01:24 Pineapple user.info sysinit: setting up led WLAN 00:01:24 Pineapple user.info sysinit: setting up led WAN 00:01:24 Pineapple user.info sysinit: setting up led USB 00:01:24 Pineapple user.info sysinit: setting up led LAN 00:01:23 Pineapple kern.info kernel: [ 83.720000] usbserial_generic 1-1.4.4:1.4: generic converter detected 00:01:23 Pineapple kern.info kernel: [ 83.720000] usb 1-1.4.4: generic converter now attached to ttyUSB3 00:01:23 Pineapple kern.info kernel: [ 83.710000] usbserial_generic 1-1.4.4:1.3: generic converter detected 00:01:23 Pineapple kern.info kernel: [ 83.700000] usbserial_generic 1-1.4.4:1.2: generic converter detected 00:01:23 Pineapple kern.info kernel: [ 83.700000] usb 1-1.4.4: generic converter now attached to ttyUSB2 00:01:23 Pineapple kern.info kernel: [ 83.690000] usb 1-1.4.4: generic converter now attached to ttyUSB1 00:01:23 Pineapple kern.info kernel: [ 83.680000] usbserial_generic 1-1.4.4:1.1: generic converter detected 00:01:23 Pineapple kern.info kernel: [ 83.680000] usb 1-1.4.4: generic converter now attached to ttyUSB0 00:01:23 Pineapple kern.info kernel: [ 83.670000] usbserial_generic 1-1.4.4:1.0: generic converter detected 00:01:23 Pineapple kern.info kernel: [ 83.670000] USB Serial support registered for generic 00:01:23 Pineapple kern.info kernel: [ 83.660000] usbcore: registered new interface driver usbserial 00:01:20 Pineapple kern.info kernel: [ 80.600000] usbcore: deregistering interface driver usbserial 00:01:20 Pineapple kern.info kernel: [ 80.590000] usbcore: deregistering interface driver usbserial_generic 00:01:20 Pineapple kern.info kernel: [ 80.590000] USB Serial deregistering driver generic 00:01:10 Pineapple user.info sysinit: ZTE MF110 (Movistar) detected. Attempting mode switch 00:01:10 Pineapple user.info sysinit: 1d6b:0002 2109:0810 0781:5571 1a40:0101 19d2:0124 00:01:08 Pineapple user.notice root: 3G: Connection Script here, searching for modems Ant the connection does not work. We think that the problem is in the pppd daemon and the "LCP: timeout sending Config-Requests" but we're not sure if we're doing everything OK. We also tried to modify the switch case and change the uci set network.wan2.device=/dev/ttyUSB1 To uci set network.wan2.device=/dev/ttyUSB2 But with no success. Any ideas? Thank you very much! Quote
segarrra Posted July 8, 2013 Author Posted July 8, 2013 Ok, finally found the configuration that works! First, I had to use the ttyUSB4 interface: ... uci set network.wan2.device=/dev/ttyUSB4 ... And also had to change the number of the ATD command in /etc/chatscripts/3g.chat (I think that this is related to the 3g operator): ... OK "ATD*99#" ... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.