ace1dragon

Thanks for your response b0N3Z. Yes I am connected to my home network and trying to understand the entire process before I get connected to other network. Basically Here are the procedures that I followed and no result for getting any Clients connected: First of all I am using a Laptop with Windows-10 Enterprise version installed on my laptop that I am performing these tasks. I also have Ubuntu on Virutal Box which also gave me the same result. 1. Reset the Tetra Wifi Pineapple to factor default 2. Connected the power AC to The unit 3. Connected the Micro-USB cable to ETH1 of the box and the other two USB to the laptop. 4. Under network and sharing made sure the "Realtek USB FE Family Controller #2" is showing there. 5. Assigned the IP Address of 172.16.42.42 with Subnet Mask of 255.255.255.0 and DNS Server of 8.8.8.8 only. 6. Made sure also in my WIFI setting under Sharing I have added the new Wifi-Pineapple is set there. At this time, I was able to log into 172.16.42.1:1471 URL and see the main menu of Wifi Pineapple. Then I followed the manual as well as checking the Video that Darren had regarding setup and getting a new client shows up on the system which was: 1. At first made sure that the version is updated to version 1.1.2 as the Firmware and there was no more upgrade available there. ( I had done this section before at the beginning when I got the unit and had the network RJ45 cable connected to the unit, but right now that cable is not connected. Only USB attachment is connected) 2. Under Networking for Wifi Client Mode I ran the Scan and got the unit connected to one of my WIFI Access Point which was 2.4GHZ speed. I was able to connect it one of my 5GHZ as well as 2.4GHZ two diffent time without any problem. It got connected and had an IP Address of 192.168.1.44 from my DHCP pool of IP Addresses. (By the way I am also usin "wlan0" that shows under MAC Address on the Networking page too. 3. Under Access point also made sure the Access Point Channel is set at 11, with SSID and Hide Open AP was also checked. No more changes there. 4. Now I went into PineAP and made sure that PineAP Daemon is enabled and all the boxes on the left are checked and then Save PineAP Settings. 5. After that, I went into Recon and selected 2.4GHZ mark and ran a SCAN. It completed 100% and showed me the list of all the SSIDs bt only the main SSID name and their MAC Address and no other PC or Laptops even though I had one Laptop that was connected to one of my 2.4GHZ network same as the one I chose up under Network. I then selected 5GHZ radion button and ran SCAN and same thing. Just the main SSID but no PC or even my IPHONE which was on 5GHZ speed as well as other PC which did not show anything. 6. I went into Client Filtering and manually added the Mac Address of one Laptop on 2.4GHZ and one PC on 5GHZ as well as made sure the SSID Filtering shows those SSID from my WIFI unit and both section has "ALlow Mode" on. Now when I go into Dashboard, all I see only 2-SSID pool. One is my 5GHZ and one is 2.4GHZ and that is it. No Client is connected at all. I even turned off the Wifi on my phone and the laptop and turned them back on to see if they can get connected to this unit but nothing happed.

I am having the same problem not being able to have any client connected. Here are the procedures that I followed and no result for getting any Clients connected: First of all I am using a Laptop with Windows-10 Enterprise version installed on my laptop that I am performing these tasks. I also have Ubuntu on Virutal Box which also gave me the same result. 1. Reset the Tetra Wifi Pineapple to factor default 2. Connected the power AC to The unit 3. Connected the Micro-USB cable to ETH1 of the box and the other two USB to the laptop. 4. Under network and sharing made sure the "Realtek USB FE Family Controller #2" is showing there. 5. Assigned the IP Address of 172.16.42.42 with Subnet Mask of 255.255.255.0 and DNS Server of 8.8.8.8 only. 6. Made sure also in my WIFI setting under Sharing I have added the new Wifi-Pineapple is set there. At this time, I was able to log into 172.16.42.1:1471 URL and see the main menu of Wifi Pineapple. Then I followed the manual as well as checking the Video that Darren had regarding setup and getting a new client shows up on the system which was: 1. At first made sure that the version is updated to version 1.1.2 as the Firmware and there was no more upgrade available there. ( I had done this section before at the beginning when I got the unit and had the network RJ45 cable connected to the unit, but right now that cable is not connected. Only USB attachment is connected) 2. Under Networking for Wifi Client Mode I ran the Scan and got the unit connected to one of my WIFI Access Point which was 2.4GHZ speed. I was able to connect it one of my 5GHZ as well as 2.4GHZ two diffent time without any problem. It got connected and had an IP Address of 192.168.1.44 from my DHCP pool of IP Addresses. (By the way I am also usin "wlan0" that shows under MAC Address on the Networking page too. 3. Under Access point also made sure the Access Point Channel is set at 11, with SSID and Hide Open AP was also checked. No more changes there. 4. Now I went into PineAP and made sure that PineAP Daemon is enabled and all the boxes on the left are checked and then Save PineAP Settings. 5. After that, I went into Recon and selected 2.4GHZ mark and ran a SCAN. It completed 100% and showed me the list of all the SSIDs bt only the main SSID name and their MAC Address and no other PC or Laptops even though I had one Laptop that was connected to one of my 2.4GHZ network same as the one I chose up under Network. I then selected 5GHZ radion button and ran SCAN and same thing. Just the main SSID but no PC or even my IPHONE which was on 5GHZ speed as well as other PC which did not show anything. 6. I went into Client Filtering and manually added the Mac Address of one Laptop on 2.4GHZ and one PC on 5GHZ as well as made sure the SSID Filtering shows those SSID from my WIFI unit and both section has "ALlow Mode" on. Now when I go into Dashboard, all I see only 2-SSID pool. One is my 5GHZ and one is 2.4GHZ and that is it. No Client is connected at all. I even turned off the Wifi on my phone and the laptop and turned them back on to see if they can get connected to this unit but nothing happed.

One more note on this subject. I am at Current Version of 1.1.2 not 1.1.0. Sorry about the confusion.

I have got my Tetra two days ago and have been struggling to get any client gets connected to it either with 2.4 or 5GHZ. Unfortunately none of them shows any clients connected. I only see SSIDS in pool with two Mac Address. I have ran Recon and got all the Mac Addresses added to the poll. Client Filtering is enabled and see those three Mac Addresses that I have selected. I have checked mark all the boxes under PinAP and save the PinAP setting and SSID Pool here shows the two network SSID. I have also updated the unit with the latest Firmware of 1.1.0 and no more updates is available either. What am I doing wrong and why cannot I see any client. By the way, I have reset the unit to Factor default at least 4 times and restarted everything and nothing works. In additions, I have the unit connected to the cable with 1GB speed WIFI. Of course if I remove that, then no internet connection. Please help me to figure it out or I may have to send this unit back. Thanks,