Jump to content

Hackituria

Active Members
  • Content Count

    22
  • Joined

  • Last visited

  • Days Won

    1

About Hackituria

  • Rank
    Hak5 Fan

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Yes, I knew it. Of course, this is the problem but it's impossible to recover the initial state of wlan0 and wlan0-1 interfaces using the web panel without problems. for this, I had to change the code of Networking module, and with this I achieved to recover this initial state.
  2. Evil Portal It is a problem with duplicated BSSID. I did a factory reset and I analyzed the /var/run/hostapd-phy0.conf file and I saw that wlan0-1 interface had 02:13:37:A7:11:7F MAC address and wlan0 00:13:37:A7:11:7F. But after Ichanged wlan0 MAC address and disabled Management AP, I have reasigned the old MAC adrress and I have seen that in the /var/run/hostapd-phy0.conf both wlan0 and wlan0-1 have the same MAC address, so I have change wlan0 MAC address to 02:13:37:A7:11:7F and both work well. But my question is, why it is happening this?
  3. I tested this and it works correctly. When I disable and hide the Management AP I could change the MAC address of wlan0 not with many problemas, but when I supplanted the victim MAC address, the cautive portal didn't appear. But this wasn't the most important problem. When I tried to reasign the old MAC address to wlan0 interface, the blue light disappeared and neither Management AP nor Open AP were up. Why occur this?
  4. I have the TETRA device and I want to get the maximum txpower. I set US on the configuration and I have 30 dBm on txpower. I have been changing the tx power on /etc/conffig/wireless file and I have analyzed the emision power. I only could set 30dBm or less. This is the limit existent on TETRA? Is it possible amplify it? Thanks!
  5. OK. I wil have to do it. But if when I change the MAC address i will have this problems, How can i config a Evil Twin attack?
  6. It doesn't work. Maybe because I changed /etc/config/wireless file, can it be?
  7. This is exactly what happened, but how can I solve it? How can I recovery those interfaces?
  8. Can it be because of duplicated MAC addresses?
  9. Yes my password have more than 8 digits. I think i lost /var/run/wifi-phy0.pid file when I change the MAC address on the GUI and i don't know why...
  10. hostapd-phy0.conf: driver=nl80211 logger_syslog=-1 logger_syslog_level=0 logger_stdout=127 logger_stdout_level=2 country_code=US ieee80211d=1 hw_mode=g channel=11 ieee80211n=1 ht_coex=0 ht_capab=[LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][DSSS_CCK-40] interface=wlan0 ctrl_interface=/var/run/hostapd ap_isolate=1 max_num_sta=100 disassoc_low_ack=1 preamble=1 wmm_enabled=1 ignore_broadcast_ssid=0 uapsd_advertisement_enabled=1 auth_algs=3 wpa=0 ssid=Pineapple_Opn bridge=br-lan bssid=00:13:37:a7:11:7f bss=wlan0-1 ctrl_interface=/var/run/hostapd ap_isolate=1 disassoc_low_ack=1 preamble=1 wmm_enabled=1 ignore_broadcast_ssid=0 uapsd_advertisement_enabled=1 wpa_passphrase=**Password** auth_algs=3 wpa=2 wpa_pairwise=CCMP ssid=WP_Man bridge=br-lan wpa_key_mgmt=WPA-PSK okc=0 disable_pmksa_caching=1 bssid=00:13:37:a7:11:7f /var/run/wifi-phy0.pid doesn`t exist!!
  11. Maybe it can be for this problem, exposed on System log: Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): Configuration file: /var/run/hostapd-phy0.conf Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): Duplicate BSSID 00:13:37:a7:11:7f on interface 'wlan0-1' and 'wlan0'. Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): 1 errors found in configuration file '/var/run/hostapd-phy0.conf' Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): Failed to set up interface with /var/run/hostapd-phy0.conf Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): Failed to initialize interface Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): cat: can't open '/var/run/wifi-phy0.pid': No such file or directory Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): Command failed: Invalid argument Tue Feb 5 11:13:56 2019 daemon.notice netifd: radio0 (1243): Device setup failed: HOSTAPD_START_FAILED But I changed /var/run/hostapd-phy0.conf file and /etc/config/wireless file, but it didn't work.
  12. This is my dmesg output, there is not nothing about wlan: [ 0.000000] Linux version 3.18.84 (@cc1b3ee85bbf) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #204 Wed Oct 24 00:10:59 UTC 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 3 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 803a7cf0, node_mem_map 81000000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=PINEAPPLE-TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125668K/131072K available (2748K kernel code, 126K rwdata, 580K rodata, 184K init, 187K bss, 5404K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz [ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] NET: Registered protocol family 16 [ 0.090000] MIPS: machine is WiFi Pineapple TETRA [ 0.100000] ar71xx: using random MAC address for eth0 [ 0.320000] ar71xx: using random MAC address for eth1 [ 0.540000] registering PCI controller with io_map_base unset [ 0.550000] PCI host bridge to bus 0000:00 [ 0.550000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.560000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.570000] pci 0000:00:00.0: [168c:abcd] type 00 class 0x020000 [ 0.570000] pci 0000:00:00.0: invalid calibration data [ 0.570000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit] [ 0.570000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.570000] pci 0000:00:00.0: supports D1 [ 0.570000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.570000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.570000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit] [ 0.580000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref] [ 0.580000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.590000] Switched to clocksource MIPS [ 0.590000] NET: Registered protocol family 2 [ 0.600000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.600000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.610000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.620000] TCP: reno registered [ 0.620000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.630000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.630000] NET: Registered protocol family 1 [ 0.640000] PCI: CLS 0 bytes, default 32 [ 0.640000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.670000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.680000] msgmni has been set to 245 [ 0.690000] io scheduler noop registered [ 0.690000] io scheduler deadline registered (default) [ 0.700000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.710000] console [ttyS0] disabled [ 0.730000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.740000] console [ttyS0] enabled [ 0.750000] bootconsole [early0] disabled [ 0.760000] m25p80 spi0.0: found s25fl008k, expected m25p80 [ 0.760000] m25p80 spi0.0: s25fl008k (1024 Kbytes) [ 0.770000] 4 cmdlinepart partitions found on MTD device spi0.0 [ 0.770000] Creating 4 MTD partitions on "spi0.0": [ 0.780000] 0x000000000000-0x000000040000 : "u-boot" [ 0.790000] 0x000000040000-0x000000080000 : "u-boot-env" [ 0.790000] 0x000000080000-0x0000000c0000 : "caldata" [ 0.800000] 0x0000000c0000-0x000000100000 : "mb0" [ 0.800000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 0.810000] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit [ 0.820000] nand: 2048MiB, SLC, page size: 4096, OOB size: 224 [ 0.820000] Scanning device for bad blocks [ 1.100000] random: nonblocking pool is initialized [ 1.100000] 2 cmdlinepart partitions found on MTD device ar934x-nfc [ 1.110000] Creating 2 MTD partitions on "ar934x-nfc": [ 1.110000] 0x000000000000-0x000000200000 : "kernel" [ 1.120000] 0x000000200000-0x000080000000 : "ubi" [ 1.140000] libphy: ag71xx_mdio: probed [ 1.730000] ag71xx-mdio.1: Found an AR934X built-in switch [ 1.770000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 2.370000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 2.380000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 2.380000] TCP: cubic registered [ 2.390000] NET: Registered protocol family 17 [ 2.390000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.410000] 8021q: 802.1Q VLAN Support v1.8 [ 2.410000] UBI: auto-attach mtd5 [ 2.420000] UBI: attaching mtd5 to ubi0 [ 15.010000] UBI: scanning is finished [ 15.040000] UBI: attached mtd5 (name "ubi", size 2046 MiB) to ubi0 [ 15.040000] UBI: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes [ 15.050000] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 15.060000] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 15.060000] UBI: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0 [ 15.070000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 15.080000] UBI: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 858528783 [ 15.090000] UBI: available PEBs: 0, total reserved PEBs: 4092, PEBs reserved for bad PEB handling: 80 [ 15.100000] UBI: background thread "ubi_bgt0d" started, PID 243 [ 15.100000] UBI: ubiblock0_0 created from ubi0:0(rootfs) [ 15.110000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 15.120000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 15.130000] Freeing unused kernel memory: 184K [ 16.760000] init: Console is alive [ 16.760000] init: - watchdog - [ 18.740000] usbcore: registered new interface driver usbfs [ 18.740000] usbcore: registered new interface driver hub [ 18.750000] usbcore: registered new device driver usb [ 18.790000] SCSI subsystem initialized [ 18.800000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 18.810000] ehci-platform: EHCI generic platform driver [ 18.820000] ehci-platform ehci-platform: EHCI Host Controller [ 18.820000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 18.830000] ehci-platform ehci-platform: TX-TX IDP fix enabled [ 18.840000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 18.860000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 18.860000] hub 1-0:1.0: USB hub found [ 18.870000] hub 1-0:1.0: 1 port detected [ 18.870000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 18.880000] ohci-platform: OHCI generic platform driver [ 18.890000] uhci_hcd: USB Universal Host Controller Interface driver [ 18.900000] usbcore: registered new interface driver usb-storage [ 19.840000] init: - preinit - [ 21.350000] mount_root: loading kmods from internal overlay [ 21.760000] UBIFS: background thread "ubifs_bgt0_1" started, PID 335 [ 22.240000] UBIFS: recovery needed [ 22.840000] eth0: link up (1000Mbps/Full duplex) [ 23.040000] UBIFS: recovery completed [ 23.040000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 23.050000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 23.060000] UBIFS: FS size: 2049933312 bytes (1954 MiB, 3972 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs) [ 23.070000] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 23.070000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 22711189-AFDB-4B8E-A1CC-DAC7162DB5BE, small LPT model [ 23.090000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 23.120000] block: extroot: not configured [ 23.130000] UBIFS: un-mount UBI device 0, volume 1 [ 23.130000] UBIFS: background thread "ubifs_bgt0_1" stops [ 23.140000] UBIFS: background thread "ubifs_bgt0_1" started, PID 338 [ 24.160000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 24.170000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 24.180000] UBIFS: FS size: 2049933312 bytes (1954 MiB, 3972 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs) [ 24.190000] UBIFS: reserved for root: 4952683 bytes (4836 KiB) [ 24.190000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 22711189-AFDB-4B8E-A1CC-DAC7162DB5BE, small LPT model [ 24.220000] mount_root: loading kmods from internal overlay [ 24.450000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 24.470000] block: extroot: not configured [ 24.480000] mount_root: switching to jffs2 overlay [ 24.540000] eth0: link down [ 24.550000] procd: - early - [ 24.560000] procd: - watchdog - [ 25.390000] procd: - ubus - [ 26.410000] procd: - init - [ 28.740000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68 [ 28.750000] Backport generated by backports.git backports-20151218-0-g2f58d9d [ 28.870000] ath: EEPROM regdomain: 0x0 [ 28.870000] ath: EEPROM indicates default country code should be used [ 28.870000] ath: doing EEPROM country->regdmn map search [ 28.870000] ath: country maps to regdmn code: 0x3a [ 28.870000] ath: Country alpha2 being used: US [ 28.870000] ath: Regpair used: 0x3a [ 28.880000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 28.880000] ieee80211 phy0: Atheros AR9340 Rev:3 mem=0xb8100000, irq=47 [ 28.890000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 28.930000] ath: EEPROM regdomain: 0x0 [ 28.930000] ath: EEPROM indicates default country code should be used [ 28.930000] ath: doing EEPROM country->regdmn map search [ 28.930000] ath: country maps to regdmn code: 0x3a [ 28.930000] ath: Country alpha2 being used: US [ 28.930000] ath: Regpair used: 0x3a [ 28.940000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 28.950000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40 [ 28.960000] usbcore: registered new interface driver ath9k_htc [ 29.180000] RPC: Registered named UNIX socket transport module. [ 29.180000] RPC: Registered udp transport module. [ 29.190000] RPC: Registered tcp transport module. [ 29.190000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 29.220000] tun: Universal TUN/TAP device driver, 1.6 [ 29.220000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 29.260000] usbcore: registered new interface driver rt2800usb [ 29.270000] usbcore: registered new interface driver rtl8187 [ 29.300000] usbcore: registered new interface driver rtl8192cu [ 29.340000] usbcore: registered new interface driver cdc_acm [ 29.350000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 29.380000] usbcore: registered new interface driver cdc_wdm [ 29.400000] nf_conntrack version 0.5.0 (1966 buckets, 7864 max) [ 29.440000] usbcore: registered new interface driver ums-alauda [ 29.450000] usbcore: registered new interface driver ums-cypress [ 29.460000] usbcore: registered new interface driver ums-datafab [ 29.470000] usbcore: registered new interface driver ums-freecom [ 29.480000] usbcore: registered new interface driver ums-isd200 [ 29.500000] usbcore: registered new interface driver ums-jumpshot [ 29.510000] usbcore: registered new interface driver ums-karma [ 29.510000] usbcore: registered new interface driver ums-sddr09 [ 29.520000] usbcore: registered new interface driver ums-sddr55 [ 29.550000] usbcore: registered new interface driver ums-usbat [ 29.570000] usbcore: registered new interface driver usbserial [ 29.570000] usbcore: registered new interface driver usbserial_generic [ 29.580000] usbserial: USB Serial support registered for generic [ 29.650000] xt_time: kernel timezone is -0000 [ 29.660000] usbcore: registered new interface driver asix [ 29.680000] usbcore: registered new interface driver ax88179_178a [ 29.690000] usbcore: registered new interface driver cdc_ether [ 29.700000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 29.720000] usbcore: registered new interface driver pl2303 [ 29.720000] usbserial: USB Serial support registered for pl2303 [ 29.730000] PPP generic driver version 2.4.2 [ 29.740000] NET: Registered protocol family 24 [ 29.750000] usbcore: registered new interface driver qmi_wwan [ 29.760000] usbcore: registered new interface driver rndis_host [ 29.770000] usbcore: registered new interface driver sierra_net [ 29.780000] usbcore: registered new interface driver option [ 29.790000] usbserial: USB Serial support registered for GSM modem (1-port) [ 39.380000] device eth1 entered promiscuous mode [ 39.380000] br-lan: port 1(eth1) entered forwarding state [ 39.390000] br-lan: port 1(eth1) entered forwarding state [ 40.410000] br-lan: port 1(eth1) entered disabled state [ 41.490000] eth0: link up (1000Mbps/Full duplex) [ 42.630000] eth1: link up (100Mbps/Full duplex) [ 42.710000] br-lan: port 1(eth1) entered forwarding state [ 42.710000] br-lan: port 1(eth1) entered forwarding state [ 44.710000] br-lan: port 1(eth1) entered forwarding state
×
×
  • Create New...