napisani
-
Posts
57 -
Joined
-
Last visited
Posts posted by napisani
-
-
I will entertain any offer but i know that they mark4 alone goes for 100 dollars. How about 130 for the whole lot?
-
Hey Thanks, my bad..
-
Hi All,
is anyone interested in purchasing my equipment directly - otherwise i might post it on ebay.
There's nothing wrong with it - I've had my fun and I can use the cash.
anyone interested? - shoot me an offer - I will accept paypal transactions
NOTE:
there is one additional cable that is not displayed in this picture that is also included in the lot - usb to barrel cable for powering the AP using the battery pack.
-
Hi all,
sorry if this has been asked before, but I couldn't find an answer
I am getting a message like this when I enable karma
(im running the newest firmware)
KARMA is disabled when handling probe request
does anyone know why or a solution?
thanks,
napisani
-
Thanks Seb that answered my question
-
I have been running the 4 AA battery pack with standard fuji batteries. If I have a usb flash drive plugged in the battery only seems to handle the pineapple for about an hour. After that, it doesn't seem to have enough juice to keep the pineapple up and running, although the lights still power on.
By using rechargeable battery packs, are you back charging the pineapple through the usb? If so could you still plug in a usb flash drive?
if anyone could snap a picture it would be helpful.
Thanks,
~napisani
-
no you shouldn't need to enable anything else to start picking up clients. But, karma does not actually broadcast all ssids i don't think, it only broadcasts the ssid "pineapple" (or whatever you change it to). But when client computers are looking for access points it will act as if it were the access point.
For example, when karma is enabled, and I go to view available wireless networks on my mac, I can see every ap I have ever connected too plus the pineapple ssid. No matter which one I select it will establish a connection to the pineapple.
R u running the latest firmware 2.1.2?
-
That feature in pineapple is called karma, make sure it is enabled. It will authorize any computer that is attempting to connect to any router. For example, if I had a computer called NICK-PC and when it powered on it searched for the SSID "wifi" the pineapple would pick up the request and snag the connection as if it were the router emitting the "wifi" SSID.
hope that helps.
-
same here
-
fuji batteries, I used a multimeter to determine the voltage being pushed out and it read about 6 volts. is that right? I think the ac adapter is like 12
-
for some reason I never get the pineapple to boot up when using the battery pack that holds 4 double As.
Is there a trick to it? I even tried putting a smaller tip on the end to better fit the ap51 power jack.
any suggestions?
-
Lol nvm ill keep mine haha
-
I was thinking about selling my mkIII anyone interested?
-
Thanks barry for those settings, it worked perfectly :)
-
Hi all, Thanks for all the handy info, I'm give it a shot tonight. Thanks again!
~napisani
-
has anyone gotten this to work on lion, I tried all of the exact same settings with and without the router address populated - nothing
-
I attempted to set the up on my mac. However, it seems like when ever I set up my ethernet adapter to have manual settings and enable internet sharing it completely stops my connection to the internet.
I have tried using wifi as an internet source and my tethered iPhone, no joy with either.
it seems like dhcp needs to be enabled in order to appropriately share an internet connection between two adapters.
can some one please share their system settings?
Thank you,
~napisani
-
Where can I find this script? I would like to check it out if that is alright. Could you pm it to me perhaps?
Thanks
~napisani
-
thanks for the reply is there anyway that you could post your wp3.sh script so I could read it?
I'm interested to see how it differs from what I have been trying to do.
-
I gave it a shot. I think that the script does something funny to the ip tables because it is trying to send out dhcp. I tried ripping out all of the dhcp support in the script but it didn't seem to help.
The problem I was having was that once I get the pineapple set up with wp3.sh then run jasager I drop the connection to the pineapple.
do you know of any other features within the jasagerpwn script that would potentially cause this type of a problem.
Thanks a lot sebkinne,
Nick
-
Has anyone tried to use JasagerPwn with the the pineapple 3? does it work?
are there any other scripts set up for the mkIII?
Thanks,
Nick
-
I had the exact same problem when I first got my ap51 from hak5, no matter how long I let it boot I never got a reply when I pinged the 172.16.42.1.
I just flashed it with the newest version of the firmware at wifipineapple.com
booted and worked fine since..
-
it worked like a charm :)
thanks for the help sebkinne
-
I was having some trouble with the easyflash application using windows too. I uninstalled and reinstalled the winpcap and made sure that the driver IS running on stratup. The flashing process was hanging at the ip assignment stage before that.
[SOLD]Selling my equipment
in Trading Post
Posted
sold!