[General NANO Discussion]

After having played with my new Nano for some days, it seems to be working - at least to start with - and at least without having started any modules.

But after a while (say one hour) it looses connectivity.

The registered "clients" then have no WiFi connectivity. I.e. they are no longer connected through the WiFi Pineapple.

If I then connect a new Client to the WiFi Pineapple, it is detected and listed as a new "client", but it does not have any WiFi connectivity.

The Android App also seem to be an a Beta stage (?)

As to modules - I have posted some comments on some of them - NONE of them seem to be working properly. :-(

Skib

[General NANO Discussion]

After having given up yesterday, I'm back again!

I installed firmware version 1.0.6 (which I saw was available today), and inserted an SD Card (found the Formatting command under USB in the Advanced Menu), and suddenly most (all?) of my issues were gone !! :-)

Thank you, HAK5, for firmware version 1.0.6!

I don't know what did the trick (either the new firmware or the SD card), but I suspect that lack of free available memory space caused most of my problems.

I also installed a Module (onto the SD card) - the SSLstrip - which seemed to be working OK.

Suddenly - now this product is what I hoped it would be!

Great Fun.

[General NANO Discussion]

My Issue no. 3: I cannot set Client PineAP filter entries from MACs from Scan results on the Recon page. They never appear in the Clients window on the Filters page.

My Issue no 4: I am unable to redirect a web browser to the Landing Page. On the Landing Page I have written a short sentence to be shown on the connected browser. When I enable the Landing Page, the message "404 Not Found, nginx 1.4.7" is shown on the connected browser.

My Issue no. 5 - and counting:

After having installed a few Modules, I also have several issues with them.

I also tried to uninstall/remove some modules, and to Update some, but NOTHING seemed to work (!)

So at this stage I am giving up - for now.

I realize that the Nano is far from a finished product, but rather something that requires a lot of debugging and fixing.

Debugging would be an exciting task - for those who have time to spare - but I am not one of them.

Still - I would like to follow the discussions here, and continue working with the Nano at a later stage - when it has matured a little.

(But I must say that I am a little bit SCARED of the low level of things. How can anyone send something like this - obviously as little tested as this - onto the "market"?)

I am using a Nano with Firmware version 1.0.5 and the Android WiFiPineapple App.

I have a dmesg output - taken after the Pineapple lost connectivity - but I don't know how/where to post/send it. Please advice.

Skib

[General NANO Discussion]

Another issue:

My Nano has found 2 clients - two of my smartphones.

They are connected through the PA to some web page (via WiFi and/or the phone network), and all works fine.

But after some time they all loose connection. On the browsers on my smartphones, I see the error message "no connection", etc.

How can I debug this to find where the problem lies?

(e,g, using SSH on a PC, connected via WiFi to the AP?)

Skib

[General NANO Discussion]

How to manage the SSID Pool?

I am using the Android WiFi Pineapple App, connected to the Nano.

There are various issues.

One is managing the SSID Pool.

When I Remove one SSID, it sais "SSID removed successfully", but the SSID seems to remain in the pool.

When I Clear the entire pool, it sais "SSID pool cleared successfully", but it is still there when I "Refresh" it.

Saving PineAP settings does not make any difference.

What is the problem?

Skib

[How to download and install Modules?]

I'm blushing!

It is all there - and working perfectly.

One just has to scroll horizontally to see the entire lines.

May be not a perfect UI, but I should have seen it immediately.

(Perhaps and hopefully this WILL help other newcomers having the same problem (?))

[How to download and install Modules?]

Hi.

I have just received my Wifi Pinapple Nano, and started trying it out. I have connected it to an Android phone using the WiFi Pinapple App. Last firmware installed: 1.0.5. Most of what I have had time to try so far, works nicely.

However, I seem unable to download any Modules.

When I click on the "Get Modules from WiFiPineapple.com" (on the "Manage Modules" menu), I see the list of available Modules. But then I am unable to do achieve anything. I have tried to click/tap on a module, but nothing happens.

How is this supposed to work?

Have I missed something?

Skib