[Remove/Replace non-U3 CD Partition from USB drive]

First, try UFDUtility v 3.2.1.0 , it's the original consumer-application for USBest-controllers

and allows you to do most of the things the MPT does ( It can't flip the RMB )

Go to "Autorun manager" and check "Single Partition" :

http://www.mediafire.com/file/yzvzqmg2z3z/UFDUtility.7z

If that doesn't do it :

Please define "nothing happens" :)

Do any of the MPT's you tried even see the device or anything,

indicated by the first port turning blue in the UI?

(press F3 to enumerate USB-ports, this tool doesn't autoscan)

Some general advice for working with MPT :

Disconnect other USB-devices, especially composite, some MPT install a modified USB-driver,

it might get confused by other devices .

Only insert the UFD after the MPT has started and the driver loaded,

do not access the device with any other programs !

Obviously, you need admin-rights and loading of unsigned drivers must be allowed,

AntiVirus and other security-software should not be allowed to interfere and

XP Pro is still better than Vista/win7 for this task .

I tried this version of UT165 UFDUtility v3.2.4.0 and i didn't try the version of the soft that U send with the link http://www.mediafire.com/file/yzvzqmg2z3z/UFDUtility.7z

because it was impossible to be extracted from WinRar or 7zip. Anyway i tried "Autorun Manager" and the device cannot be found by the utility.

When i tried MPTool (UT163 Multi-Devices Production Tool) v3.9.80.0 and other version of this soft, I followed these steps:

1. I installed the MDPT tool

2. I connected the flash (USBest) and the device was recognized as FABULK device.

3. I pressed F3 to Enumerate the ports

and when i pressed start, shows the code 0xa2 with 0MB capacity

With UT165 MP Tool 1.65.25.0 the same thing but when i pressed start the code changes from 0x12 0x28 to 0x12 0x28 0xa2 always with 0MB

With Super Stick Recovery Tool V1.0.2.19 it shows the size of flash drive 0MB

I think that is a broken drive but i need help for another device if U can with the following information by Chip Genius v2.64

Device Name: USB Mass Storage Device(USB DISK 30X USB Device)

PnP Device ID: VID = 13FE PID = 1D00

Serial Number: 5&&2B17EFFA&&0&&3

Revision: 1.00

Device Type: Standard USB device - USB2.0 High-Speed

Chip Vendor: phison(??)

Chip Part-Number: UP8/UP10 --------> chip Genius V3.0: UP13

Product Vendor: USB

Product Model: DISK 30X

I tried many utilities:

Phison UP13 UP14 UP12 V1.96, MP2232 V1.06, MPALL v2.01.00 (recognize the device but shows a mesagge "Flash Status Error") and all of these utilities show the capacity 0MB. I think that may be exist a solution to fix the problem because when i try with Acronis Media for Workstation can recognize the device and even can be formatted but when I plug in it again and try to access shows me a message "Please insert disk into drive". Please if you have any solution

please inform me. Thanks for your help and Happy New Year 2010. Best regards

[Remove/Replace non-U3 CD Partition from USB drive]

IOSYS,

Thank so much....UT165 MP Tool 1.65.14.0 fixed my solution. Only issue that came up afterwards was that my laptop was not recognizing any USB drive... I did system restore and my 32GB A-Data Flash drive is back into business...

Thanks again...

I have the same problem. I tried everything that is mentioned above and nothing happens

Chip Genius v3.0 it read USB as following:

Device Name: USB Mass Storage Device(USBest USB2FlashStorage USB Device)

PnP Device ID: VID = 1307 PID = 0163

Serial Number: 5&&2B17EFFA&&0&&3

Revision: 0.00

Device Type: Standard USB device - USB2.0 High-Speed

Chip Vendor: USBest(??)

Chip Part-Number: UT163

Product Vendor: USBest

Product Model: USB2FlashStorage

I tried:

MPTool UT163 v3.9.12 ~ MPTool UT163 v3.9.80

UT165 v1.65.10 ~ UT165 1.65.25.0

Super Stick Recovery Tool V1.0.2.19

and still doesn't work. Please i need some help here