Arayanz
-
Posts
3 -
Joined
-
Last visited
Posts posted by Arayanz
-
-
@ Arayanz :
Try downloading ALL the MPT's for the UT163, sometimes the latest version doesn't work on older
chip-revisions .. I think that's the issue you have, the error-code seems to confirm a version-mismatch .
EDIT : There's a manual for the UT165 MPT here :
http://translate.googleusercontent.com/tra...Tg-MFXn67xxiBqw
Much of it also applies to the UT163 MPT .
IOsys Hi,
Thank so much for helping....
I tried following versions (all available) from flashboot.ru and found that problem is still there. Same symptoms even though each time FABULK showed up when flash is connected.
I have tried
UT163 / 3.9.8/3.9.12/3.9.29/3.9.31/3.9.35
Just listing above to make sure i am not missing anything.
Btw, Following is the procedure i am folloiwng
1. Installing the MDPT tool
2. Connecting the flash (A-Data) and driver is installed and it is recognized as FABULK device
3. Starting MDPT tool and click on F1 Settings / Ut163 to change the partition (LUN0) to Auto and partition option checked. I did not change anything on the vendor data side and click OK
4. F3 (enumerate) and getting error "Number of Input devices is not matched with maximum device list!!!"
I am ignoring this considering that my laptop has only three USB slots and min in the tool is 4
5. Port 1 shows the code:0x54 with 0Mb space and VID/PID as 0/0
6. Tried InfUpdate to make the VID/PID as showing in the settings options for MDPT but not change. Even though it unloads and loads the driver (FABULK) with this step.
7. If I press start, the code changes from 0x54 to 0x54/0xa2
Any thoughts?
Thanks for your help
-
I am in same boat... Suddenly my 32GB A-Data USB got this USBest issue... I downloaded UT163 MPT tool(UT163 MPTool v3.9.35.0) and after installing the driver by MTP (FABULK), it read the USB as following
Port1:
Status:Code 0x54
Capacity 0MB
USB VIP/PID = 0 <------------------------------ChipGenius reads it as 1307/0163
Write Protect = NO
Operation Mode = Unknown
********************************CHIP GENIUS*************
Device Name: +FABULK
PnP Device ID: VID = 1307 PID = 0163
Serial Number: 5&&38C8E674&&0&&1
Revision: (Information not returned)
Device Type: Standard USB device - USB2.0 High-Speed
Chip Vendor: USBest(??)
Chip Part-Number: UT163
Product Vendor: FABULK
Product Model:
********************************************************
I realized from the Flashboot.ru that I can assign VID/PIV using C: \ Program Files \ MDPT \ Driver \ InfUpdate.ex but it does not change anything in the MPT tool after referesh. Parition is set to AUTO in the settings Tab.
If I press start, i get Status Code : 0x54 0xa2
Please kindly help. I had given up on this USB but now there is some hope... Is that FABULK is not loaded correctly or am I using incorrect versoin of MPT tool... 0x54 means Firmware version mismatch with controller type. I see FABULK added into the list of drivers and also the light on my USB flashes with this driver installed....
Please help...
Thanks in advance...
Aray
Remove/Replace non-U3 CD Partition from USB drive
in USB Hacks
Posted
IOSYS,
Thank so much....UT165 MP Tool 1.65.14.0 fixed my solution. Only issue that came up afterwards was that my laptop was not recognizing any USB drive... I did system restore and my 32GB A-Data Flash drive is back into business...
Thanks again...