kingkaran977 Posted September 19, 2021 Share Posted September 19, 2021 It's been more than 4 months of getting this gift from Microsoft and I haven't accessed pineapple dashboard till now bcz every time I get stuck somewhere! Previously during initial setup by holding the reset button for 4 second was not working so I finished my setup through USB flashing. But again this time the password I set in config.txt, and when I try to login in web interface through the username: root & password: 0xKaran_ it says "invalid credentials". Wifi AP 0xKaran is showing but again password is not working there too. My config.txt file: Quote ######################################################################################### # .NN, # # .cxxdl' xMMO 'cdxxl' # # .c0WMNk;,NMMW:,xXMMKo. # # ...:KMMMWMMMMWMMMXc... . # # , .l0NMMMNXMMMMMMMMMMMMXNMMMWKl' xWd # # ,0Wd .':xNMMMMMMMMMMMMMMMMNkc'. ;KM0' # # lWMo .;dNMMMMMMMMMMMMMMWx:. .l. dMWc # # :WWo oNd .;xKWMMMMMMMMMMMMMMMMMMMMWXx:. dWX: dMW; # # ,NWo oMW: .. ..,lOXWMMMMMMMMMMWN0o;.. .. cWMl dMN' # # .XMx oWN; lc .loooolcooclooool. cXl oMWc kMK. # # oMW' ,WMl cMW: lWMW0d:;cdd:;:o0WMWl lMW: OMW' ,WMl # # 0M0 xMX. .XMd .lo:.,dXMMMMMMXd,.:ol. kMK. 'NMd KMO # # NMd KMk lMN. .;:xOxollccddcclloxOx:;. 'WM: OM0 xMX # # WMo .XMx dMK oNMMMMWOc;;ol;;cOWMMMMNo .XMl kMK dMN # # NMx 0MO :Kd. .lllcl;.:0WMMMMW0:.;lclll. .xK; 0MO kMX # # __ ___ ______ _ _____ _ .:W0;,oxl:::oOOo:::lxo,;0W: _ .ONo KMk # # \ \ / (_| ____(_) | __ (_) ;cKMMMMWk:.;,.;kWMMMMKc;. | | .OX: # # \ \ /\ / / _| |__ _ | |__) _ _ __ ___ __ _ _ __ _ __ | | ___ # # \ \/ \/ / | | __| | | | ___| | '_ \ / _ \/ _` | '_ \| '_ \| |/ _ \ # # \ /\ / | | | | | | | | | | | | __| (_| | |_) | |_) | | __/ # # \/ \/ |_|_| |_| |_| |_|_| |_|\___|\__,_| .__/| .__/|_|\___| # # ----------------------------------------------------| |-- | |---------------------- # # |_| |_| # ######################################################################################### # This file is used to configure automatic enrollment of your WiFi Pineapple Mark VII # # # # To enroll your WiFi Pineapple automatically, edit this file and place it on the # # root of a USB flash disk when performing the first boot. # # # # For more information, visit https://docs.hak5.org. # ######################################################################################### # Generic System Configuration # ######################################################################################### ROOT_PASSWORD="0xKaran_" HOSTNAME="0xKaran" TIMEZONE="utc" ######################################################################################### # Wireless AP Configuration # ######################################################################################### MANAGEMENT_SSID="0xKaran" MANAGEMENT_PSK="0xKaran_" MANAGEMENT_HIDDEN=1 MANAGEMENT_DISABELD=0 OPEN_SSID="Open" OPEN_HIDDEN=0 COUNTRY_CODE=US ######################################################################################### # Filters Configuration # ######################################################################################### CLIENT_FILTER="ALLOW" SSID_FILTER="ALLOW" ######################################################################################### # Hak5 Cloud C2 Configuration # ######################################################################################### ENABLE_C2=1 I tried reseting it following this method but not working, it is again & again prompting me for the login credentials --> https://modemly.com/Hak5-WiFI-Pineapple-router-setup#reset & https://docs.hak5.org/hc/en-us/articles/360055166053-Firmware-Recovery I'm able to access this page http://172.16.42.1:1471 but not this http://172.16.42.1:80 Also clear my doubt, What is this Hostname? Link to comment Share on other sites More sharing options...
Irukandji Posted September 20, 2021 Share Posted September 20, 2021 http://172.16.42.1:1471/ is the one. Not the port 80. Link to comment Share on other sites More sharing options...
includeV Posted September 21, 2021 Share Posted September 21, 2021 Hi, Have you tried flashng the device via USB and just leaving the password as set in the config file? ie dont change anything? Maybe, try getting the device to flash using default settings might work. Once/if you get into the web interface (your not missing much), then you can start changing passwords, ip addresses etc. When i first brought the thing, I couldnt get the hold for 4 secons button process to work. So I had to flash via USB, but I never configured anything just let it do its thing, then I change all I needed. If unable to get it working via USB default, then i'd say your device is f**** Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.