karimnabiil Posted August 22, 2019 Share Posted August 22, 2019 Hey lovely people, So i've just received my Nano earlier today and was playing around with it for a little bit. I had issues with devices connecting to the open AP, so i decided to factory reset it after buying a SD card because it does apparently fix the issue for some reason. However, after i went through with pressing the factory reset button from the webpage, i gave it about 3 minutes and there was suddenly a power cut. So right now im terrified that it might be bricked. The blue light is still blinking, but it's been like for that about 15 minutes and i can't neither access the web interface or do anything. Can someone please help me out or point out something im not aware of as i've been anticitpating its arrival for so bloody long 😞 Link to comment Share on other sites More sharing options...
Cap_Sig Posted August 22, 2019 Share Posted August 22, 2019 If you cannot access the web UI then something may have went wrong with your factory reset. You will need to do a firmware recovery: https://docs.hak5.org/hc/en-us/articles/360010471774-Firmware-Recovery Make sure to download the recovery firmware, NOT upgrade firmware. Link to comment Share on other sites More sharing options...
karimnabiil Posted August 22, 2019 Author Share Posted August 22, 2019 Thank you so much mate. So basically i've typed down sudo ifconfig eth1 192.168.1.2 netmask 255.255.255.0 up, which enabled my to access 192.168.1.1 and update the firmware. So as of this moment, the update has been going on for about 15 mins. Should i now reset the Pineapple facing USB Ethernet interface back to DHCP or 172.16.42.42 with netmask 255.255.255.0 by pretty much typing the same command but with putting the 172 address? I can't tell if it did reboot or not still tho because it has blinked a couple of times about 2-3 minutes ago, that's what im tryna make sure of right now Link to comment Share on other sites More sharing options...
Cap_Sig Posted August 22, 2019 Share Posted August 22, 2019 5 minutes ago, karimnabiil said: which enabled my to access 192.168.1.1 and update the firmware. Just to verify you did use the factory recovery firmware? 5 minutes ago, karimnabiil said: Should i now reset the Pineapple facing USB Ethernet interface back to DHCP Yes, then try accessing the web UI for initial setup. Link to comment Share on other sites More sharing options...
karimnabiil Posted August 22, 2019 Author Share Posted August 22, 2019 You're a life saver man, everything is sorted. Just one more question tho So i did the whole setup through linux this time and used Darren ws6.sh script for the internet sharing. However, I can't seem to be able to connect to the internet through the UI to download modules and what not. So my question is do you reckon i can still acess the UI from my mac since it seemed to work over there or will i be stuck with Linux as the intital setup took place there? Link to comment Share on other sites More sharing options...
karimnabiil Posted August 22, 2019 Author Share Posted August 22, 2019 Also even though i formatted the sd card, it wasn't giving me an option to install the modules on it rather the internal memory. was i missing something? Link to comment Share on other sites More sharing options...
Cap_Sig Posted August 22, 2019 Share Posted August 22, 2019 @karimnabiil glad to help. 1 hour ago, karimnabiil said: So my question is do you reckon i can still acess the UI from my mac since it seemed to work over there or will i be stuck with Linux as the intital setup took place there? You can access the web UI from any device that you have properly connected to the nano. Its not tied to the setup system. Sounds like you need to check your internet sharing settings or you could connect wifi as a client is another method. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.