Jump to content
balzaar

No clients show up after a deauth attack.

Recommended Posts

Hi forum,

Just received the Tetra device this week but I have already run into issues with it. Clients do now show up after a basic recon and deauth attack on the set targets. I have followed the instructions from the Hak5 video referred to below, but still no clients available to me.

I start with the recon stage and add the SSID to the PineAP Pool, then add the targeted devices MAC addresses to the PineAP from the options in the recon view. The MAC addresses can be visually seen in section Filters and these are set to Allow Listed. The SSID can also be identified under section PineAP and SSID Pool.

The following PineAP options are enabled:

  • PineAP Daemon: Enabled    
  • Autostart PineAP: Enabled    
  • Allow Associations
  • Log PineAP Events
  • Client Connect Notifications
  • Client Disconnect Notifications
  • Beacon Response
  • Broadcast SSID Pool

Other issues that I have identified with the Tetra device.

  • No valid OUI information is presented about the available devices during the recon. Only shows "Unknown MAC prefix. This MAC was likely globally assigned by the hardware vendor. It has probably not been randomized for privacy." on all MAC addresses.
  • Capture handshakes cannot be performed. I get a confirmation that the action is performed but no output.

I have performed a factory reset twice and set up the device according to the video from Hak5, see URL below.

WiFi Hacking Workflow - The NEW WiFi Pineapple 2.5 Firmware - Hak5 2514
https://www.youtube.com/watch?v=CcnCbxoUWps

The Tetra device is running the latest available firmware (v2.5.4), and the overall setup is vanilla and no fancy modules etcetera installed yet.

Anyone got a clue what´s causing this issue? Debug info required to proceed in locating the issue?

Share this post


Link to post
Share on other sites

the devices you are deauthing are updated and wont connect to the spoofed hotspot.

Share this post


Link to post
Share on other sites

Thanks for the reply!

Updated how? Isn't the deauthentication frame part of the regular interaction between the AP and its hosts? 

When I Airreplay-ng on a laptop with a WiFi card, the same AP and clients are deauthenticated. I just cannot get the same to work on the Tetra.

Share this post


Link to post
Share on other sites

i wasnt think about a deauth attack. but yea i used pmkid attack ive not found a client in recon or anywere. thinking now as typingwhy i haven restart it yet. worse case reflash. so not just you

Share this post


Link to post
Share on other sites
On 6/2/2019 at 1:32 PM, nikmel420 said:

i wasnt think about a deauth attack. but yea i used pmkid attack ive not found a client in recon or anywere. thinking now as typingwhy i haven restart it yet. worse case reflash. so not just you

I will look into PMKID as you mentioned. Thanks for your input!

Share this post


Link to post
Share on other sites

Hi there,

My nano does not deauth and capture either. My old kali box abd alfa card works no problem. I think I may have a faulty unit also attached a highgain antenna and still nothing.

Kev

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...