Jump to content
Sebkinne

[RELEASE] WiFi Pineapple Firmware v2.3.x

Recommended Posts

Hi everyone,

After releasing firmware version 2.3.0 at DEF CON, I hadn't gotten around to creating a forum thread of it yet. As usual, please leave all feedback in this thread.

 - The Hak5 Development Team

Changelog 2.3.1:

  • Recon
    • Fixed an issue where timed recon scans would fail the first time around.
    • Fixed an issue where the stop handshake capture button would persist after a capture had completed.

Changelog 2.3.2

  • Recon
    • Fixed an issue where performing recon scans would lock up all further PineAP actions.

Changelog 2.3.0:

  • Recon
    • Added the ability to capture WPA Handshakes by clicking on the arrow next to a WPA / WPA2 encrypted network.
    • Fixed an issue where multicast MAC addresses were shown as clients to wireless networks.
  • PineAP
    • Fixed an issue where PineAP would remain running when the wlan1mon interface had been removed, causing confusion.
  • Filters
    • Fixed an issue where some combinations of filters did not apply correctly.
  • Logging
    • Fixed an issue where non-completed associations were logged as completed.
  • General
    • Fixed an issue where notifications would show invalid timestamps in Firefox.
    • Fixed an issue that prevented the timezone set during initial Setup from persisting across reboots.

 

Download:
Over the air via your WiFi Pineapple's webinterface, or at https://wifipineapple.com/downloads

  • Like 3
  • Upvote 1

Share this post


Link to post
Share on other sites

Thanks for the update.

Everything that I've reported seems to have been fixed now. However, there might be an issue with PineAP not collecting any essid's into the pool but not 100% sure until I leave out somewhere near people as there's little to no wireless AP's near my home >.>

Share this post


Link to post
Share on other sites

Nothing big or bad, but there is a bug with Recon / PineAP which we are releasing a fix for tomorrow.

Until then, I want to prevent people updating to a bugged update, just to update again.

Share this post


Link to post
Share on other sites

Hi Sebkinne,

Thanks for clarifying this! Saved me some time going out, walking around in the heat ...

Share this post


Link to post
Share on other sites

Hi, with version 2.3.0 I had an issue when connected my wifi card ALFA AWUS036NHA to access Internet. All the configuration done under "Access Points" was established to default, losing the configurations done for "Management SSID" "Management PSK" "Disable Management AP" and "Open SSID". It happened only the first time when connected the ALFA card, after reconfigure all the section, the configurations remains even using the ALFA card.

Share this post


Link to post
Share on other sites
35 minutes ago, NazgulAngmar said:

Hi, in version 2.3.1, 3 unexpected restarts in a period of 3 hours. One of the restarts after the usb connection to my phone and enabling tethering. 

more likely a power issue, by the sounds of the symptoms anyway

 

  • Like 1

Share this post


Link to post
Share on other sites

When I run recon now I end up getting this error.

firefox_2018-08-17_14-56-25.png.38a4b4aa494097f4a71395f07977cd2b.png

 

EDIT: Fixed with the 2.3.2 Update ?

Thanks guys! Keep up the awesome work.

Edited by Exmix

Share this post


Link to post
Share on other sites

With the latest firmware when I try to download the results of a large recon scan (~30 minutes with lots of SSIDs) I get a 500 error, smaller scans however give me the expected JSON file.

Share this post


Link to post
Share on other sites

I am unable to connect to the open SSID I create get a network disabled service rejection or something or other....Never happened until I updated. Also PineAp has to be restarted when wanting to reckon again.....

Share this post


Link to post
Share on other sites
20 minutes ago, simoncfc said:

I am unable to connect to the open SSID I create get a network disabled service rejection or something or other....Never happened until I updated. Also PineAp has to be restarted when wanting to reckon again.....

Are your filters set correctly?

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...