Jump to content
THEPACK76

Dependencies What am I missing?

Recommended Posts

I unbox my NANO today I got through the setup and have basic functionality. I try to install DNSspoof and nmap modules. They both say Dependencies Not Installed. I click Not Installed. It says it will install dependencies. I click internal.  It says installing and goes for a few seconds and then it goes back to not installed.

I am also a little disappointed that there is more videos on the functionality and explain some of the things you can do with this. 

Thank you for your time and attention.

Anthony

Share this post


Link to post
Share on other sites

Internal storage is just a couple mega-bytes, and using it should be avoided if possible.
If not, make sure you know exactly how much space the stuff you're installing will take up.

Are you sure the Nano has internet connectivity?

Share this post


Link to post
Share on other sites

Yes, Internet sharing is working and the bulletin loads. I think the space is the problem. I didn't realize it was so tight. I'm getting and SD card today. Should I just reset and start over? I tried to remove DNSSpoof and nmap and its just stuck there now. I really need those two working. I have a presentation I was gonna use this for next week.

I'm going a hacking demonstration. Any cool looking wow stuff you recommend. Maybe some pointers of how to do it lol.  

Thanks for your help either way.

 

Anthony

Share this post


Link to post
Share on other sites

Yeah i'd factory-reset it before adding a SD-card, as alot of dependencies may have been installed to the internal storage.
Should fix your problem straight away. Just be careful installing to internal. :)
 

Share this post


Link to post
Share on other sites

Ok sounds good. I'll work on it tonight.  I was gonna focus on DNSSpoof and the build in component for my hacking demo. Any other suggestions that you think look impressive?

Thanks again for your help and quick responses. 

Share this post


Link to post
Share on other sites

i also posted on a forum  post that was similar. Getting these errors after trying to download a packet capture from the site survey module, which is install on the SD card I formatted in the software.

Here are the errors 

[  247.700000] Write-error on swap-device (8:0:1328)
[  247.700000] Write-error on swap-device (8:0:1336)
[  247.700000] Write-error on swap-device (8:0:1344)
[  247.750000] Write-error on swap-device (8:0:1352)
[  247.800000] Write-error on swap-device (8:0:1360)
[  247.800000] Write-error on swap-device (8:0:1368)
[  247.800000] Write-error on swap-device (8:0:1376)
[  247.850000] Write-error on swap-device (8:0:1384)
[  247.850000] Write-error on swap-device (8:0:1392)
[  247.890000] Write-error on swap-device (8:0:1400)
[  247.890000] Write-error on swap-device (8:0:1408)
[  247.890000] Write-error on swap-device (8:0:1416)
[  248.040000] Write-error on swap-device (8:0:1424)
[  248.040000] Write-error on swap-device (8:0:1432)
[  248.180000] EXT4-fs error (device sdb1): ext4_find_entry:1289: inode #1308229: comm awk: reading directory lblock 0
[  248.470000] EXT4-fs error (device sdb1): ext4_find_entry:1289: inode #1308229: comm awk: reading directory lblock 0
[  250.640000] usb 1-1.2: new high-speed USB device number 6 using ehci-platform
[  250.780000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[  250.810000] scsi host2: usb-storage 1-1.2:1.0
[  251.810000] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0933 PQ: 0 ANSI: 6
[  251.820000] sd 2:0:0:0: Attached scsi generic sg0 type 0
[  252.130000] sd 2:0:0:0: [sdc] 62333952 512-byte logical blocks: (31.9 GB/29.7 GiB)
[  252.150000] sd 2:0:0:0: [sdc] Write Protect is off
[  252.150000] sd 2:0:0:0: [sdc] Mode Sense: 21 00 00 00
[  252.150000] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  252.190000]  sdc: sdc1 sdc2
[  252.200000] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[  252.860000] Buffer I/O error on dev sdb1, logical block 3702784, lost sync page write
[  252.870000] JBD2: Error -5 detected when updating journal superblock for sdb1-8.
[  252.880000] Aborting journal on device sdb1-8.
[  252.880000] Buffer I/O error on dev sdb1, logical block 3702784, lost sync page write
[  252.890000] JBD2: Error -5 detected when updating journal superblock for sdb1-8.
[  252.930000] EXT4-fs (sdc1): couldn't mount as ext3 due to feature incompatibilities
[  252.950000] EXT4-fs (sdc1): couldn't mount as ext2 due to feature incompatibilities
[  253.180000] EXT4-fs (sdc1): recovery complete
[  253.180000] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[  253.690000] Adding 1004024k swap on /dev/sdcard/sd2.  Priority:-3 extents:1 across:1004024k 
 

 

Share this post


Link to post
Share on other sites
7 hours ago, THEPACK76 said:

i also posted on a forum  post that was similar. Getting these errors after trying to download a packet capture from the site survey module, which is install on the SD card I formatted in the software.

Here are the errors 

[  247.700000] Write-error on swap-device (8:0:1328)
[  247.700000] Write-error on swap-device (8:0:1336)
[  247.700000] Write-error on swap-device (8:0:1344)
[  247.750000] Write-error on swap-device (8:0:1352)
[  247.800000] Write-error on swap-device (8:0:1360)
[  247.800000] Write-error on swap-device (8:0:1368)
[  247.800000] Write-error on swap-device (8:0:1376)
[  247.850000] Write-error on swap-device (8:0:1384)
[  247.850000] Write-error on swap-device (8:0:1392)
[  247.890000] Write-error on swap-device (8:0:1400)
[  247.890000] Write-error on swap-device (8:0:1408)
[  247.890000] Write-error on swap-device (8:0:1416)
[  248.040000] Write-error on swap-device (8:0:1424)
[  248.040000] Write-error on swap-device (8:0:1432)
[  248.180000] EXT4-fs error (device sdb1): ext4_find_entry:1289: inode #1308229: comm awk: reading directory lblock 0
[  248.470000] EXT4-fs error (device sdb1): ext4_find_entry:1289: inode #1308229: comm awk: reading directory lblock 0
[  250.640000] usb 1-1.2: new high-speed USB device number 6 using ehci-platform
[  250.780000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[  250.810000] scsi host2: usb-storage 1-1.2:1.0
[  251.810000] scsi 2:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0933 PQ: 0 ANSI: 6
[  251.820000] sd 2:0:0:0: Attached scsi generic sg0 type 0
[  252.130000] sd 2:0:0:0: [sdc] 62333952 512-byte logical blocks: (31.9 GB/29.7 GiB)
[  252.150000] sd 2:0:0:0: [sdc] Write Protect is off
[  252.150000] sd 2:0:0:0: [sdc] Mode Sense: 21 00 00 00
[  252.150000] sd 2:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  252.190000]  sdc: sdc1 sdc2
[  252.200000] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[  252.860000] Buffer I/O error on dev sdb1, logical block 3702784, lost sync page write
[  252.870000] JBD2: Error -5 detected when updating journal superblock for sdb1-8.
[  252.880000] Aborting journal on device sdb1-8.
[  252.880000] Buffer I/O error on dev sdb1, logical block 3702784, lost sync page write
[  252.890000] JBD2: Error -5 detected when updating journal superblock for sdb1-8.
[  252.930000] EXT4-fs (sdc1): couldn't mount as ext3 due to feature incompatibilities
[  252.950000] EXT4-fs (sdc1): couldn't mount as ext2 due to feature incompatibilities
[  253.180000] EXT4-fs (sdc1): recovery complete
[  253.180000] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[  253.690000] Adding 1004024k swap on /dev/sdcard/sd2.  Priority:-3 extents:1 across:1004024k 
 

 

This is a classic example of the SD-card bug that several people have experienced with the Nano.
After a lot of research and debugging i'm confident that the problem lies within a kernel-module(s) or the hardware of the Nano. (I still haven't tested SD-cards with another chipset to rule out hardware issues.)
But yeah. My solution to this HUGE problem was to take out the SD-card, and then use a normal usb memory-stick, and mount it as /sd
Making the Nano behave as if the memory-stick is the SD-card.

Share this post


Link to post
Share on other sites

I took a usb stick and formatted it with ext on my kali linux. 

What are the next steps to do your suggested configuration. Not the strongest linux.

Thanks alot for your help.

Share this post


Link to post
Share on other sites

i tried formatting on the Pineapple, it didn't like it. So I did it on Kali.

Then I'll plug into the pineapple, that's where I'm not sure how to do it the way you said.

 

Anthony

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...