Jump to content
Sign in to follow this  
coyotlgw

Intermittent failure to assign eth1

Recommended Posts

I have been dealing with an oddity, wonder if anybody has seen similar and has suggestions.

I have a Pineapple Nano running firmware 1.1.1.  When I connect the USB y-cables to the Nano and a laptop running Ubuntu 16.04 LTS, about half the time I see an IPv6 address assigned but never IPv4 and have to unplug, cool, then try again.

Same issue on a Raspberry Pi 3 running Kali.  (Yes, I went there.)

Example:

user@***-Ubuntu:~$ ifconfig eth1
eth1      Link encap:Ethernet  HWaddr 00:c0:ca:90:d1:f9  
          inet6 addr: fe80::5851:89df:4911:ae3c/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:58 errors:0 dropped:0 overruns:0 frame:0
          TX packets:94 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2668 (2.6 KB)  TX bytes:15606 (15.6 KB)

It seems like if I then disconnect, wait a few seconds and reconnect, it goes through the second or third try:

eth1      Link encap:Ethernet  HWaddr 00:c0:ca:90:d1:f9
          inet addr:172.16.42.42  Bcast:172.16.42.255  Mask:255.255.255.0
          inet6 addr: fe80::be0f:d824:b0c0:2e77/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1022 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1074 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:601481 (601.4 KB)  TX bytes:256879 (256.8 KB)


(realized this was in a thread on wlan0 issue, deleted there and moved here)

Share this post


Link to post
Share on other sites

When this happens, try unplugging only the thickest of the two USB connectors from your laptop, and plug it back in again. If that works, sharing the dmesg of the Pineapple would help debug any issue better.

Share this post


Link to post
Share on other sites

Heh... new record for attaching on the first try, of course.  I will post as soon as I see it again :)

Share this post


Link to post
Share on other sites

Does not connect... dmesg on the laptop (not pineapple) is:
[

193784.536658] usb 3-1: USB disconnect, device number 7
[193784.537507] asix 3-1:1.0 eth1: unregister 'asix' usb-0000:02:00.0-1, ASIX AX88772 USB 2.0 Ethernet
[193802.506634] usb 3-1: new high-speed USB device number 8 using xhci_hcd
[193802.654381] usb 3-1: New USB device found, idVendor=0b95, idProduct=772a
[193802.654392] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[193802.654398] usb 3-1: Product: AX88x72A
[193802.654403] usb 3-1: Manufacturer: ASIX Elec. Corp.
[193802.654407] usb 3-1: SerialNumber: 90D1F9
[193803.458523] asix 3-1:1.0 eth1: register 'asix' at usb-0000:02:00.0-1, ASIX AX88772 USB 2.0 Ethernet, 00:c0:ca:90:d1:f9
[193804.567154] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[193804.570411] asix 3-1:1.0 eth1: link down
[193804.573993] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[193805.059705] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[193805.062239] asix 3-1:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0x4DE1


 

Share this post


Link to post
Share on other sites

waited a while and tried cold, full plug in.  dmesg -T from laptop:

[Wed Aug 31 22:36:50 2016] usb 3-1: new high-speed USB device number 9 using xhci_hcd
[Wed Aug 31 22:36:50 2016] usb 3-1: New USB device found, idVendor=0b95, idProduct=772a
[Wed Aug 31 22:36:50 2016] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[Wed Aug 31 22:36:50 2016] usb 3-1: Product: AX88x72A
[Wed Aug 31 22:36:50 2016] usb 3-1: Manufacturer: ASIX Elec. Corp.
[Wed Aug 31 22:36:50 2016] usb 3-1: SerialNumber: 90D1F9
[Wed Aug 31 22:36:51 2016] asix 3-1:1.0 eth1: register 'asix' at usb-0000:02:00.0-1, ASIX AX88772 USB 2.0 Ethernet, 00:c0:ca:90:d1:f9
[Wed Aug 31 22:36:52 2016] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[Wed Aug 31 22:36:52 2016] asix 3-1:1.0 eth1: link down
[Wed Aug 31 22:36:52 2016] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[Wed Aug 31 22:36:53 2016] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[Wed Aug 31 22:36:53 2016] asix 3-1:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0x4DE1
[Wed Aug 31 22:37:21 2016] asix 3-1:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0x4DE1

dmesg from pineapple:

[    0.000000] Linux version 3.18.36 (openwrt@19a38d794f6d) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49403) ) #20 Fri Aug 19 01:58:53 UTC 2016
[    0.000000] MyLoader: sysp=8a14b024, boardp=44b65156, parts=b69f8d32
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 80355cf0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=PINEAPPLE-NANO  console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60944K/65536K available (2467K kernel code, 126K rwdata, 528K rodata, 260K init, 188K bss, 4592K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is WiFi Pineapple NANO
[    0.380000] Switched to clocksource MIPS
[    0.380000] NET: Registered protocol family 2
[    0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.400000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.400000] TCP: reno registered
[    0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.420000] NET: Registered protocol family 1
[    0.420000] PCI: CLS 0 bytes, default 32
[    0.420000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.450000] msgmni has been set to 119
[    0.460000] io scheduler noop registered
[    0.460000] io scheduler deadline registered (default)
[    0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a AR933X UART
[    0.480000] console [ttyATH0] enabled
[    0.490000] bootconsole [early0] disabled
[    0.500000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    0.500000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    0.520000] 5 tp-link partitions found on MTD device spi0.0
[    0.520000] Creating 5 MTD partitions on "spi0.0":
[    0.520000] 0x000000000000-0x000000020000 : "u-boot"
[    0.530000] 0x000000020000-0x000000134ec0 : "kernel"
[    0.540000] 0x000000134ec0-0x000000ff0000 : "rootfs"
[    0.540000] mtd: device 2 (rootfs) set to be root filesystem
[    0.550000] 1 squashfs-split partitions found on MTD device rootfs
[    0.550000] 0x000000dc0000-0x000000ff0000 : "rootfs_data"
[    0.560000] 0x000000ff0000-0x000001000000 : "art"
[    0.560000] 0x000000020000-0x000000ff0000 : "firmware"
[    0.590000] libphy: ag71xx_mdio: probed
[    1.190000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    1.200000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    1.200000] TCP: cubic registered
[    1.200000] NET: Registered protocol family 17
[    1.210000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.220000] 8021q: 802.1Q VLAN Support v1.8
[    1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.240000] Freeing unused kernel memory: 260K (8036f000 - 803b0000)
[    2.630000] init: Console is alive
[    2.630000] init: - watchdog -
[    5.310000] usbcore: registered new interface driver usbfs
[    5.310000] usbcore: registered new interface driver hub
[    5.320000] usbcore: registered new device driver usb
[    5.370000] SCSI subsystem initialized
[    5.380000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.390000] ehci-platform: EHCI generic platform driver
[    5.400000] ehci-platform ehci-platform: EHCI Host Controller
[    5.400000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.410000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.440000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.440000] hub 1-0:1.0: USB hub found
[    5.440000] hub 1-0:1.0: 1 port detected
[    5.450000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    5.460000] ohci-platform: OHCI generic platform driver
[    5.470000] uhci_hcd: USB Universal Host Controller Interface driver
[    5.480000] usbcore: registered new interface driver usb-storage
[    5.700000] init: - preinit -
[    5.780000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.440000] random: procd urandom read with 10 bits of entropy available
[    6.440000] hub 1-1:1.0: USB hub found
[    6.450000] hub 1-1:1.0: 4 ports detected
[    6.710000] mount_root: loading kmods from internal overlay
[    6.960000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[    7.030000] jffs2: notice: (325) jffs2_build_xattr_subsystem: complete building xattr subsystem, 18 of xdatum (0 unchecked, 17 orphan) and 18 of xref (0 dead, 17 orphan) found.
[    7.050000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[    7.060000] block: extroot: not configured
[    7.120000] jffs2: notice: (322) jffs2_build_xattr_subsystem: complete building xattr subsystem, 18 of xdatum (0 unchecked, 17 orphan) and 18 of xref (0 dead, 17 orphan) found.
[    7.210000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[    7.250000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[    7.260000] block: extroot: not configured
[    7.270000] mount_root: switching to jffs2 overlay
[    7.330000] procd: - early -
[    7.330000] procd: - watchdog -
[    7.760000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[    7.770000] scsi host0: usb-storage 1-1.2:1.0
[    7.910000] usb 1-1.3: new high-speed USB device number 5 using ehci-platform
[    8.600000] procd: - ubus -
[    8.870000] scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0933 PQ: 0 ANSI: 6
[    9.190000] sd 0:0:0:0: [sda] 62333952 512-byte logical blocks: (31.9 GB/29.7 GiB)
[    9.210000] sd 0:0:0:0: [sda] Write Protect is off
[    9.210000] sd 0:0:0:0: [sda] Mode Sense: 21 00 00 00
[    9.210000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    9.240000]  sda: sda1 sda2
[    9.240000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.620000] procd: - init -
[   14.090000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[   14.100000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[   14.290000] ath: EEPROM regdomain: 0x0
[   14.290000] ath: EEPROM indicates default country code should be used
[   14.290000] ath: doing EEPROM country->regdmn map search
[   14.290000] ath: country maps to regdmn code: 0x3a
[   14.290000] ath: Country alpha2 being used: US
[   14.290000] ath: Regpair used: 0x3a
[   14.300000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   14.300000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   14.320000] usb 1-1.1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
[   14.330000] usbcore: registered new interface driver ath9k_htc
[   14.370000] RPC: Registered named UNIX socket transport module.
[   14.380000] RPC: Registered udp transport module.
[   14.380000] RPC: Registered tcp transport module.
[   14.390000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   14.400000] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities
[   14.410000] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities
[   14.430000] tun: Universal TUN/TAP device driver, 1.6
[   14.430000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   14.470000] usbcore: registered new interface driver rt2800usb
[   14.480000] usbcore: registered new interface driver rtl8187
[   14.520000] rtl8192cu: Chip version 0x10
[   14.540000] EXT4-fs (sda1): recovery complete
[   14.540000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   14.650000] rtl8192cu: MAC address: 40:a5:ef:0c:a7:a8
[   14.660000] rtl8192cu: Board Type 0
[   14.660000] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[   14.670000] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[   14.670000] ieee80211 phy1: Selected rate control algorithm 'rtl_rc'
[   14.680000] usbcore: registered new interface driver rtl8192cu
[   14.760000] usb 1-1.1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
[   14.800000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   14.820000] usbcore: registered new interface driver cdc_acm
[   14.830000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[   14.850000] usbcore: registered new interface driver cdc_wdm
[   14.870000] nf_conntrack version 0.5.0 (956 buckets, 3824 max)
[   14.940000] ath9k_htc 1-1.1:1.0: ath9k_htc: HTC initialized with 33 credits
[   14.970000] usbcore: registered new interface driver ums-alauda
[   14.980000] usbcore: registered new interface driver ums-cypress
[   15.000000] usbcore: registered new interface driver ums-datafab
[   15.010000] usbcore: registered new interface driver ums-freecom
[   15.020000] usbcore: registered new interface driver ums-isd200
[   15.030000] usbcore: registered new interface driver ums-jumpshot
[   15.060000] usbcore: registered new interface driver ums-karma
[   15.070000] usbcore: registered new interface driver ums-sddr09
[   15.080000] usbcore: registered new interface driver ums-sddr55
[   15.090000] usbcore: registered new interface driver ums-usbat
[   15.120000] usbcore: registered new interface driver usbserial
[   15.120000] usbcore: registered new interface driver usbserial_generic
[   15.130000] usbserial: USB Serial support registered for generic
[   15.170000] Adding 1004024k swap on /dev/sdcard/sd2.  Priority:-1 extents:1 across:1004024k
[   15.210000] xt_time: kernel timezone is -0000
[   15.210000] usbcore: registered new interface driver asix
[   15.220000] usbcore: registered new interface driver ax88179_178a
[   15.230000] usbcore: registered new interface driver cdc_ether
[   15.250000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.310000] usbcore: registered new interface driver pl2303
[   15.320000] usbserial: USB Serial support registered for pl2303
[   15.330000] PPP generic driver version 2.4.2
[   15.340000] NET: Registered protocol family 24
[   15.350000] usbcore: registered new interface driver qmi_wwan
[   15.350000] usbcore: registered new interface driver rndis_host
[   15.360000] usbcore: registered new interface driver sierra_net
[   15.380000] usbcore: registered new interface driver option
[   15.380000] usbserial: USB Serial support registered for GSM modem (1-port)
[   15.580000] ath9k_htc 1-1.1:1.0: ath9k_htc: FW Version: 1.4
[   15.580000] ath9k_htc 1-1.1:1.0: FW RMW support: On
[   15.590000] ath: EEPROM regdomain: 0x0
[   15.590000] ath: EEPROM indicates default country code should be used
[   15.590000] ath: doing EEPROM country->regdmn map search
[   15.590000] ath: country maps to regdmn code: 0x3a
[   15.590000] ath: Country alpha2 being used: US
[   15.590000] ath: Regpair used: 0x3a
[   15.600000] ieee80211 phy2: Atheros AR9271 Rev:1
[   22.380000] random: nonblocking pool is initialized
[   25.200000] device eth0 entered promiscuous mode
[   27.770000] eth0: link up (100Mbps/Full duplex)
[   27.770000] br-lan: port 1(eth0) entered forwarding state
[   27.780000] br-lan: port 1(eth0) entered forwarding state
[   29.330000] rtl8192cu: MAC auto ON okay!
[   29.360000] rtl8192cu: Tx queue select: 0x05
[   29.780000] br-lan: port 1(eth0) entered forwarding state
[   40.970000] device wlan0 entered promiscuous mode
[   41.160000] br-lan: port 2(wlan0) entered forwarding state
[   41.160000] br-lan: port 2(wlan0) entered forwarding state
[   43.160000] br-lan: port 2(wlan0) entered forwarding state
[   53.920000] rtl8192cu: MAC auto ON okay!
[   53.950000] rtl8192cu: Tx queue select: 0x05
[   61.430000] device wlan1mon entered promiscuous mode
[  322.920000] rtl_usb: reg 0xda8, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x81580000
[  322.970000] rtl_usb: reg 0xcf0, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x40070000
[  323.020000] rtl_usb: reg 0xa2c, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0x40070008
[  323.070000] rtl_usb: reg 0xa5c, usbctrl_vendorreq TimeOut! status:0xffffffb9 value=0xc0d300
[  323.110000] usb 1-1.1: USB disconnect, device number 3
[  323.130000] ath: phy2: Failed to wakeup in 500us
[  323.150000] ath: phy2: DMA failed to stop in 10 ms AR_CR=0x82fe9b2c AR_DIAG_SW=0x82fe9b2c DMADBG_7=0x82fe9b2c
[  323.170000] ath: phy2: Failed to wakeup in 500us
[  323.180000] usb 1-1.1: ath9k_htc: USB layer deinitialized
[  323.430000] usb 1-1.1: new high-speed USB device number 6 using ehci-platform
[  328.520000] usb 1-1.1: device descriptor read/64, error -145
[  328.780000] usb 1-1.1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested
[  328.800000] usb 1-1.2: USB disconnect, device number 4
[  329.050000] usb 1-1.2: new high-speed USB device number 7 using ehci-platform
[  329.090000] usb 1-1.1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008
[  329.200000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[  329.200000] scsi host1: usb-storage 1-1.2:1.0
[  329.210000] usb 1-1.3: USB disconnect, device number 5
[  329.340000] ath9k_htc 1-1.1:1.0: ath9k_htc: HTC initialized with 33 credits
[  329.470000] usb 1-1.3: new high-speed USB device number 8 using ehci-platform
[  329.600000] rtl8192cu: Chip version 0x10
[  329.640000] ath9k_htc 1-1.1:1.0: ath9k_htc: FW Version: 1.4
[  329.650000] ath9k_htc 1-1.1:1.0: FW RMW support: On
[  329.650000] ath: EEPROM regdomain: 0x0
[  329.650000] ath: EEPROM indicates default country code should be used
[  329.650000] ath: doing EEPROM country->regdmn map search
[  329.650000] ath: country maps to regdmn code: 0x3a
[  329.650000] ath: Country alpha2 being used: US
[  329.650000] ath: Regpair used: 0x3a
[  329.660000] ieee80211 phy3: Atheros AR9271 Rev:1
[  329.760000] rtl8192cu: MAC address: 40:a5:ef:0c:a7:a8
[  329.760000] rtl8192cu: Board Type 0
[  329.780000] rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
[  329.780000] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw_TMSC.bin
[  329.790000] ieee80211 phy4: Selected rate control algorithm 'rtl_rc'
[  330.210000] scsi 1:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0933 PQ: 0 ANSI: 6
[  330.220000] sd 1:0:0:0: Attached scsi generic sg0 type 0
[  330.530000] sd 1:0:0:0: [sdb] 62333952 512-byte logical blocks: (31.9 GB/29.7 GiB)
[  330.560000] sd 1:0:0:0: [sdb] Write Protect is off
[  330.560000] sd 1:0:0:0: [sdb] Mode Sense: 21 00 00 00
[  330.570000] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  330.590000]  sdb: sdb1 sdb2
[  330.600000] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[  331.330000] Buffer I/O error on dev sda1, logical block 3702784, lost sync page write
[  331.340000] JBD2: Error -5 detected when updating journal superblock for sda1-8.
[  331.340000] Aborting journal on device sda1-8.
[  331.350000] Buffer I/O error on dev sda1, logical block 3702784, lost sync page write
[  331.360000] JBD2: Error -5 detected when updating journal superblock for sda1-8.
[  331.730000] rtl8192cu: MAC auto ON okay!
[  331.770000] rtl8192cu: Tx queue select: 0x05

Edited by Mr-Protocol
added spoiler tags

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...