Jump to content

Trouble connecting the Tetra to a Raspberry Pi


Boosted240
 Share

Recommended Posts

I'm finally getting around to updating my old setup (see attached photos) with my Tetra.  (I've also replaced the RPi 1 with an RPi 2) 

In the original setup the MK4 was connected to the Pi via eth and all was well.  Static IP, used SSH from the MK4 to the Kali RPi.

Now with the Tetra I'm connecting to the Kali Pi via the micro USB ETH port, but I'm having no luck.  Looking on the Pi, the adapter looks like its listed using "lsusb"  but it won't show up under interfaces.  All I have is eth0 (the Pi's eth port)

Both devices are fully powered.  The Tetra at 12v, 2A.  Pi at 5v 2A.  

 

Any ideas?  

 

root@kali:~# lsusb
Bus 001 Device 008: ID 148f:2770 Ralink Technology, Corp. RT2770 Wireless Adapter
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter
Bus 001 Device 002: ID 0424:9514 Standard Microsystems Corp. SMC9514 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@kali:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:64 errors:0 dropped:0 overruns:0 frame:0
          TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5184 (5.0 KiB)  TX bytes:5184 (5.0 KiB)

wlan0     Link encap:Ethernet  HWaddr 
          inet addr:192.168.1.112  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::2c0:caff:fe32:c219/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1766 errors:0 dropped:0 overruns:0 frame:0
          TX packets:389 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:195338 (190.7 KiB)  TX bytes:58971 (57.5 KiB)

root@kali:~#

 

 

https://www.dropbox.com/sh/jr62ncj4u54sr06/AACPcQplq0QYg5WTFRWDRvnsa?dl=0

Link to comment
Share on other sites

52 minutes ago, Boosted240 said:

...Looking on the Pi, the adapter looks like its listed using "lsusb"...

Your 'lsusb' output does not show any TETRA being connected.

This is the VID:PID of a TETRA:

Bus 002 Device 005: ID 0bda:8152 Realtek Semiconductor Corp.

 

Link to comment
Share on other sites

20 minutes ago, Boosted240 said:

Okay, then 003 must be the Tetra's eth adapter?   Well then, that's really odd.

No... Unless the Pi is doing weird things and displaying wrong VID:PIDs, there is no TETRA being listed in your output. It should be the one I posted in my first reply. Is the driver loaded?

"ID 0424:ec00 Standard Microsystems Corp. SMSC9512/9514 Fast Ethernet Adapter" is the Pi's Ethernet port.

Edited by Foxtrot
Link to comment
Share on other sites

I'm not sure on the driver, but I figured the adapter would show up even if the driver wasn't present?  

How can I check for, or get the driver? I haven't run Kali in a good while, so I'm currently doing:

apt-get clean && apt-get update && apt-get upgrade -y && apt-get dist-upgrade -y

 

Thank you in advance for your assistance!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...