Jump to content

No IP from TETRA


McBean4000
 Share

Recommended Posts

I can't seem to get an IP address from my TETRA. ifconfig said the adapter is up, but no IP address issued. I've attached the log file from boot up. Any help would be appreaciated.

I'm not permited to upload this kind of file? Here is the log.

eth0 up
WASP ----> S27 PHY
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Atheros on-chip NAND FLash Controller Driver, Version 0.1 © 2010 Atheros Communications, Ltd.
Ath Nand ID[87fef17c]: 2c:48:00:26:89
ONFI MICRON MT29F16G08ABABAWP
Micronset ns -0x80000-0x1000
====== NAND Parameters ======
sc = 0x87fef158 bbt = 0x87f98538 bbt_size = 0x400 nf_ctrl = 0x485
page = 0x1000 block = 0x80000 oob = 0xe0
size = 2048MB
Setting 0xb8116290 to 0x20402d0f
Hit any key to stop autoboot: 0

Loading from device 0: ath-nand (offset 0x0)
Booting image at: 0x81000000
Image Name: MIPS OpenWrt Linux-3.18.23
Created: 2015-12-22 4:23:13 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1965951 Bytes = 1.9 MB
Load Address: 80060000
Entry Point: 80060000
Uncompressing kernel image... OK!
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...

[ 0.000000] Linux version 3.18.23 (sebkinne@buildtop) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47951) ) #3 Tue Dec 22 05:23:06 CET 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125796K/131072K available (2642K kernel code, 125K rwdata, 556K rodata, 188K init, 186K bss, 5276K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is tetra
[ 0.530000] registering PCI controller with io_map_base unset
[ 0.540000] PCI host bridge to bus 0000:00
[ 0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.550000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.560000] pci 0000:00:00.0: invalid calibration data
[ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.570000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switched to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.590000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.600000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.600000] TCP: reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.660000] msgmni has been set to 245
[ 0.660000] io scheduler noop registered
[ 0.670000] io scheduler deadline registered (default)
[ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.680000] console [ttyS0] disabled�[ 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.710000] console [ttyS0] enabled
[ 0.710000] console [ttyS0] enabled
[ 0.720000] bootconsole [early0] disabled
[ 0.720000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found s25fl008k, expected m25p80
[ 0.730000] m25p80 spi0.0: s25fl008k (1024 Kbytes)
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.750000] 0x000000040000-0x000000080000 : "u-boot-env"
[ 0.760000] 0x000000080000-0x0000000c0000 : "caldata"
[ 0.770000] 0x0000000c0000-0x000000100000 : "mb0"
[ 0.770000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48
[ 0.780000] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit
[ 0.780000] nand: 2048MiB, SLC, page size: 4096, OOB size: 224
[ 0.790000] Scanning device for bad blocks
[ 1.060000] random: nonblocking pool is initialized
[ 1.070000] 2 cmdlinepart partitions found on MTD device ar934x-nfc
[ 1.070000] Creating 2 MTD partitions on "ar934x-nfc":
[ 1.080000] 0x000000000000-0x000000200000 : "kernel"
[ 1.090000] 0x000000200000-0x000080000000 : "ubi"
[ 1.100000] libphy: ag71xx_mdio: probed
[ 1.700000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.740000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.340000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.350000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.350000] TCP: cubic registered
[ 2.360000] NET: Registered protocol family 17
[ 2.360000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.380000] 8021q: 802.1Q VLAN Support v1.8
[ 2.380000] UBI: auto-attach mtd5
[ 2.390000] UBI: attaching mtd5 to ubi0
[ 14.970000] UBI: scanning is finished
[ 15.000000] UBI: attached mtd5 (name "ubi", size 2046 MiB) to ubi0
[ 15.000000] UBI: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes
[ 15.010000] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 15.020000] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 15.020000] UBI: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0
[ 15.030000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 15.040000] UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 858528783
[ 15.040000] UBI: available PEBs: 0, total reserved PEBs: 4092, PEBs reserved for bad PEB handling: 80
[ 15.050000] UBI: background thread "ubi_bgt0d" started, PID 240
[ 15.060000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 15.070000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 15.070000] UBIFS error (pid 1): init_constants_early: too few LEBs (11), min. is 17
[ 15.090000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 15.100000] Freeing unused kernel memory: 188K (803a1000 - 803d0000)
[ 16.160000] init: Console is alive
[ 16.160000] init: - watchdog -
[ 17.500000] usbcore: registered new interface driver usbfs
[ 17.500000] usbcore: registered new interface driver hub
[ 17.510000] usbcore: registered new device driver usb
[ 17.530000] SCSI subsystem initialized
[ 17.540000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.550000] ehci-platform: EHCI generic platform driver
[ 17.550000] ehci-platform ehci-platform: EHCI Host Controller
[ 17.560000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 17.570000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 17.600000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 17.600000] hub 1-0:1.0: USB hub found
[ 17.610000] hub 1-0:1.0: 1 port detected
[ 17.610000] usbcore: registered new interface driver usb-storage
[ 18.180000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 22.030000] UBIFS: background thread "ubifs_bgt0_1" started, PID 333
[ 22.510000] UBIFS: recovery needed
[ 23.310000] UBIFS: recovery completed
[ 23.320000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 23.320000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 23.330000] UBIFS: FS size: 2057158656 bytes (1961 MiB, 3986 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 23.340000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 23.350000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 38045547-2CEB-4F61-9102-0C9CFC5FB3CE, small LPT model
[ 23.370000] mount_root: switching to jffs2 overlay
[ 23.430000] procd: - early -
[ 23.430000] procd: - watchdog -
[ 24.240000] procd: - ubus -
[ 25.250000] procd: - init -
Please press Enter to activate this console.
[ 26.390000] NET: Registered protocol family 10
[ 26.400000] ip6_tables: © 2000-2006 Netfilter Core Team
[ 26.420000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 26.430000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 26.440000] ip_tables: © 2000-2006 Netfilter Core Team
[ 26.450000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 26.480000] usbcore: registered new interface driver ums-alauda
[ 26.490000] usbcore: registered new interface driver ums-cypress
[ 26.500000] usbcore: registered new interface driver ums-datafab
[ 26.500000] usbcore: registered new interface driver ums-freecom
[ 26.510000] usbcore: registered new interface driver ums-isd200
[ 26.520000] usbcore: registered new interface driver ums-jumpshot
[ 26.530000] usbcore: registered new interface driver ums-karma
[ 26.540000] usbcore: registered new interface driver ums-sddr09
[ 26.540000] usbcore: registered new interface driver ums-sddr55
[ 26.550000] usbcore: registered new interface driver ums-usbat
[ 26.570000] usbcore: registered new interface driver usbserial
[ 26.570000] usbcore: registered new interface driver usbserial_generic
[ 26.580000] usbserial: USB Serial support registered for generic
[ 26.610000] xt_time: kernel timezone is -0000
[ 26.610000] usbcore: registered new interface driver asix
[ 26.620000] usbcore: registered new interface driver ax88179_178a
[ 26.630000] usbcore: registered new interface driver cdc_ether
[ 26.670000] cfg80211: Calling CRDA to update world regulatory domain
[ 26.670000] cfg80211: World regulatory domain updated:
[ 26.680000] cfg80211: DFS Master region: unset
[ 26.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 26.690000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 26.700000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 26.710000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 26.720000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 26.720000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 26.730000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 26.740000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 26.750000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 26.840000] PPP generic driver version 2.4.2
[ 26.850000] NET: Registered protocol family 24
[ 26.850000] usbcore: registered new interface driver rndis_host
[ 26.930000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 26.940000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 26.950000] cfg80211: Calling CRDA for country: US
[ 26.980000] cfg80211: Regulatory domain changed to country: US
[ 26.980000] cfg80211: DFS Master region: FCC
[ 26.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 27.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 27.000000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 27.010000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 27.020000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 27.030000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 27.060000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 35.220000] device eth1 entered promiscuous mode
[ 35.230000] br-lan: port 1(eth1) entered forwarding state
[ 35.230000] br-lan: port 1(eth1) entered forwarding state
[ 35.440000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 36.250000] br-lan: port 1(eth1) entered disabled state
[ 38.010000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 38.020000] device wlan0 entered promiscuous mode
[ 38.110000] br-lan: port 2(wlan0) entered forwarding state
[ 38.110000] br-lan: port 2(wlan0) entered forwarding state
[ 38.120000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 38.150000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 38.200000] device wlan1 entered promiscuous mode
[ 38.200000] br-lan: port 3(wlan1) entered forwarding state
[ 38.210000] br-lan: port 3(wlan1) entered forwarding state
[ 38.230000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 38.260000] eth1: link up (100Mbps/Full duplex)
[ 38.260000] br-lan: port 1(eth1) entered forwarding state
[ 38.270000] br-lan: port 1(eth1) entered forwarding state
[ 40.110000] br-lan: port 2(wlan0) entered forwarding state
[ 40.210000] br-lan: port 3(wlan1) entered forwarding state
[ 40.270000] br-lan: port 1(eth1) entered forwarding state

Link to comment
Share on other sites

From what interface are you trying to get an IP? The Ethernet port on the Tetra is client / wan port and not serving dhcp. Your laptop / computer .. etc wont get an ip from the tetra if you connect it thru ethernet.

Use the micro usb cable and connect it to the usb port marked eth.

Edit.. Sebkinne beat me to it... so what he said ;)

Edited by Smarty
Link to comment
Share on other sites

I understand why the rj45 jack wouldn't work now. I shut everything off and rebooted. I tried using my Andriod phone and it works. The pineapple is plugged in with the wall adapter, and the micro usb eth port is pluged into a macbook air running kali 2.0 in vm ware.

eth1 is up. no ip.

*edit*

I just plugged into my router and that works as well. The eth port on the pineapple dosent seem to work.

Edited by McBean4000
Link to comment
Share on other sites

I understand why the rj45 jack wouldn't work now. I shut everything off and rebooted. I tried using my Andriod phone and it works. The pineapple is plugged in with the wall adapter, and the micro usb eth port is pluged into a macbook air running kali 2.0 in vm ware.

eth1 is up. no ip.

*edit*

I just plugged into my router and that works as well. The eth port on the pineapple dosent seem to work.

Seeing as it shows up on your Mac, and I see it responding in dmesg, I think there is a good chance some configuration got messed up.

Can you try to factory reset your WiFi Pineapple TETRA?

Best regards,

Sebkinne

Link to comment
Share on other sites

I have had this issue and Darren couldnt even get this to work for me. What I had to do was let the pineapple boot 100% then insert the USB...

That's an issue with the network manager, to be honest. If we know what OS is being used, I recommend setting a static ip (or using the wp6.sh script) of 172.16.42.42 and checking if you get ping replies.

Best regards,

Sebkinne

Link to comment
Share on other sites

I had the same issue (eth1 up and no ip) in kali linux 2.0 x64. What i did was give a click in network manager and select USB Ethernet then click in connect and that gave me the IP. Finally run the wp6.sh script to have internet accsess in my computer and the wifi pineapple because i only had acces to the wifi pineaple. I guess that kali takes the USB Ethernet as default and ignore the wireless conection.

  • Upvote 1
Link to comment
Share on other sites

My situation has went from bad to worse. I reset the pineapple to default twice and now the pineapple shows eth1 as up, no ip (from the pineapple only). When I would plug the eth port into my computer, a box asking if I want to connect the device to mac or linux would pop up. That dosen't happen anymore after the reset (directions found in the bug tracker but now are gone). I've shut everything off and rebooted, no success. The wp6.sh script dose not work for me because my computer won't see the connection at all now.

Would it be more helpful if I put this in the bug tracker? Should I try wp6.sh from the pineapple?

Link to comment
Share on other sites

i don't know very well in vmware but sometimes i use kali 2.0 in virtualbox and i had to install an extension pack for use my usb ports with 2.0/3.0 driver because per default it uses in 1.0 driver.


I learn this when i wanted to connect an external wifi card and kali show the interface but when i scan for networks not show nothing.


so be shure you have installed all drivers or extra packs you need and these be configured appropriately.


also you can try to disable any other network interface from the VM and let only the usb of the tetra and press connect in the network manager just to see what happen if this give an ip.


or try in VirtualBox i had no problem using it.

Link to comment
Share on other sites

i don't know very well in vmware but sometimes i use kali 2.0 in virtualbox and i had to install an extension pack for use my usb ports with 2.0/3.0 driver because per default it uses in 1.0 driver.
I learn this when i wanted to connect an external wifi card and kali show the interface but when i scan for networks not show nothing.
so be shure you have installed all drivers or extra packs you need and these be configured appropriately.
also you can try to disable any other network interface from the VM and let only the usb of the tetra and press connect in the network manager just to see what happen if this give an ip.
or try in VirtualBox i had no problem using it.

Thanks! I'll try that this weekend. To be fair about my rant, Darren emailed me about my issue. All is well.

Link to comment
Share on other sites

  • 3 weeks later...

Thanks for that advice! I'll try that when I get home. I have no issue logging into the Tetra through wireless or the rj45 port connected to my router. The web interface and ssh work just fine. I cant seem to do anything with the usb ports. I can't remember why I decided to do this but I read the I can default the Tetra with

/sbin/jffs2reset

reboot

Since then the USB ports have been useless. Nothing happens when I connect the eth port to my Macbook Air (2013) running osx, Kali in VM Ware or usb booted with Kali, or my work computer a Surface Pro 2. As well I have a usb hub that gives a visual indication when something is plugged into it. The hub gives no indication that the Tetra is plugged into it.

I always power the Tetra with supplied 2A power adapter. But oddly enough I am able to power the Tetra through the usb ports. I can power the Tetra with any/all combinations. I just cant seem to transfer any data through the usb. I always have to connect wirelessly or through the rj45 port to access it.

I'm a bit of a noob with this. I always seem to take on a project that is slightly beyond me. To eliminate as many things as I could (although I don't think it matters for this issue) I decided to install Kali on a separate partition on my Macbook. I'm working on that now.

I have also tried the firmware recovery directions listed on the website. It won't work because I can't connect through the eth port.

I don't mind a good puzzle. Thats kinda why I'm attracted to this kinda thing. But I'm ready to figure this one out and move on to the next head scratcher.

Link to comment
Share on other sites

I've tried firstboot as well. No sucess.

With nothing plugged into any usb, lsusb gives me

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

If I plug my Alfa AWUS036NEH in, lsusb gives me

Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

If I plug my Mac into either micro usb and try lsusb, nothing changes?

Can someone try this and tell me your results?

  1. Please have nothing plugged into any usb on your Tetra
  2. Open a console and type lsusb
    1. Post results
  3. Plug the eth port into your computer and type lsusb again
    1. Post results

Am I insane? There is a problem here right?

Link to comment
Share on other sites

  • 4 weeks later...

Been busy lately. Haven't looked at this in a month... Now everything works?? Can someone tell me if there was an update in the last month? I need to know why it works now? Am I a noob who cant follow directions? Firmware update? Both?

To be clear, I understand my troubleshooting wasn't going anywhere. Don't know why yet. I just know I can get every port working on it now and I don't think I've done anything different to get it to work?

Edited by McBean4000
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...