Jump to content

Pineapple tetra reboots after a few minutes


johnnyg
 Share

Recommended Posts

Hi everyone,

Is anyone else experiencing a rebooting Tetra? I've tried powering my via my computer USB ports and via the twin Pineapple 15000 Juice packs she get up and running and then as soon as I the PineAP Daemon to enabled it reboots every time no matter which powering method is use.

Any help would be welcome.

Regards.

John

Link to comment
Share on other sites

I haven't experienced this, I've had it running consecutively with PineAP running for over 10 hours inside of the EDC bag on two separate occasions.

Not sure what would cause it in your situation or how to further diagnose, just wanted to point out I have had it working for prolonged periods of time. Possibly may suggest having it powered via both methods at once, so have one y-cable connected to two of your usb ports and the other y-cable connected to your two pineapple 15000 and see if you get the same results.

  • Upvote 1
Link to comment
Share on other sites

Hi Bored369,

Thanks for the advice, so I plugged the other Y cable I received into both Pineapple Juice 15000 batteries one end of each of the Y cable USB connectors into each battery so both batteris are used to supply power and into the two USB 3 ports on my PC to power the Tetra and both times a soon as I start the PineAP Daemon after about 15 seconds the Tetra reboots.

I've also contacted Hak5 returns for advice as I don't think this is little Tetra is operating as intended. I've only had it running for a few hours in total.

John

Link to comment
Share on other sites

Hi Bored369,

Thanks for the advice, so I plugged the other Y cable I received into both Pineapple Juice 15000 batteries one end of each of the Y cable USB connectors into each battery so both batteris are used to supply power and into the two USB 3 ports on my PC to power the Tetra and both times a soon as I start the PineAP Daemon after about 15 seconds the Tetra reboots.

I've also contacted Hak5 returns for advice as I don't think this is little Tetra is operating as intended. I've only had it running for a few hours in total.

John

hmm. this does seem psu related. are your PC ports usb 3.0?

Also, go grab a 12v/2a charger from your local computer store. That should get you up and going immediately. I use that + my usb cable over eth... I noticed that using two usb ports only gave me 5v/1a max! So be careful that you arent underpowering this thing. It can and will hurt it!

Link to comment
Share on other sites

Hi InfiniteDevelopment,

Thanks for your help, yes the PC USB ports are USB 3 and I agree that they might not be supplying enough power but I have the exact same result when using the Pineapple Juice 15000 battery packs I purchased with my new Tetra. I'm not very happy as I intended to use the purchased Pineapple Juice 15000 battery packs for remote deployments with the Tetra but even using both battery packs as prescribed the Tetra still reboots when I enable the PineAP Daemon! The reboot occurs from both power configurations, I've tried using different USB cables and power supplies, PC and Pineapple Juice 15000 I'm starting to suspect the Tetra is a faulty unit.

As I'm in Australia I'll try your suggestion for a charger 12v/2a and repost the results here.

As mentioned I've emailed Hak5 about thi issue but no reply as yet.

Regards.

John

Link to comment
Share on other sites

Did you email shop@hak5.org ? You should receive a reply in 1-2 business days. I also concur that it sounds like a power issue. Do you have it in this configuration?

5QwPDXH.jpg

If it's still happening with 18+ watts (either 2x Pineapple Juice or a 12V/2A adapter) I'll start suspecting software.

Can you post the output of the serial console from the moment it reboots?

Link to comment
Share on other sites

Hi Darren,

Thanks for stopping by and posting that photo of the battery configuration. I believe its another noob error on my part as I didn't have the Tetra configured with the batteries like your photo so I'll retest with this correct configuration. I suspect I've been underpower the Tetra and when I ask the Tetra to power on the PineAP Daemon she is not receiving enough power to keep the WiFi antennas powered up as well as the Tetra.

I'll retest again with your config and post the outcome here which I'm sure will be positive.

Thanks again for your time.

Regards.

John

Edited by johnnyg
Link to comment
Share on other sites

If it's still happening with 18+ watts (either 2x Pineapple Juice or a 12V/2A adapter) I'll start suspecting software.

Can you post the output of the serial console from the moment it reboots?

It may be something with software, can you give a couple steps on getting the serial output?

I was going to report back in this thread: https://forums.hak5.org/index.php?/topic/37670-stability-issues-with-red-is-wlan1mon-when-being-disabled-and-tethering-stopping/

but when I got home from Deadpool (highly recommend btw) the Tetra was restarting, I got a video of it restarting twice in 3 minutes (working on uploading to youtube and i'll post a link here)

I should have 2x2.1a + 1x1a with the two pineapple 15000 i have and the configuration of cables i was using. It appeared to restart as soon as I tried connecting to the management ap after I saw pineAP start flashing the red light consistently, but it may just have been coincidence.

Link to comment
Share on other sites

I know there's a way to do this with screen, but I'm a minicom man myself so I'll give you setup instructions for that:

Connect cable from PC to TETRA USB UART port

sudo apt-get install mincom

sudo minicom -s

Go to Serial Port setup the make sure it's set to /dev/ttyUSB0 as the device, 115200 as the speed, and 81N as in 8 data bits, 1 stop bit, no parity bit. Then save as default and either exit setup and re-issue sudo minicom without the -s, or select exit which'll drop you into the terminal. Press enter to activate -- you'll be prompted to login.

If you run this while booting you'll can watch the kernel come to life. Keep this open and log what happens when there's an issue.

Lemme tell you - having super convenient serial access in dev has been a boon. I highly recommend it.

BTW you can do the same in Windows with PuTTY and I'm sure there's something out there for mac.

I'll let the next guy school me on how screen > minicom later ;-)

Link to comment
Share on other sites

well I had to go with screen as mincom isn't available on kali for rasPi2

ended up just being:

script logTetra.txt

screen /dev/ttyUSB0 115200 8N1

So I tried to catch it on a reboot and stop it at a another reboot.

I have PineAP set to autostart all options. No other modules set to autostart.

Pineapple 15000 both ports connected to y-cable and then to the eth micro usb port

standard micro-usb cable from UART micro usb port to rasPi2 usb

Script started on Thu Feb 18 07:16:17 2016
root@kali:~# screen /deve /ttyUSB0 115200 8N1
[r[m[2J[H[?7h[?1;4;6l[?1049h[4l[?1h=[0m(B[1;24r[H[2J[H[2J
eth0 up
WASP ----> S27 PHY
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Atheros on-chip NAND FLash Controller Driver, Version 0.1 © 2010 Atheros Communications, Ltd.
Ath Nand ID[87fef17c]: 2c:48:00:26:89
ONFI MICRON MT29F16G08ABABAWP
Micronset ns -0x80000-0x1000
====== NAND Parameters ======
sc = 0x87fef158 bbt = 0x87f98538 bbt_size = 0x400 nf_ctrl = 0x485
page = 0x1000 block = 0x80000 oob = 0xe0
size = 2048MB
Setting 0xb8116290 to 0x20402d0f
Hit any key to stop autoboot: 2 1 0
Loading from device 0: ath-nand (offset 0x0)
Booting image at: 0x81000000
Image Name: MIPS OpenWrt Linux-3.18.23
Created: 2016-02-11 5:08:33 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1965951 Bytes = 1.9 MB
Load Address: 80060000
Entry Point: 80060000
Uncompressing kernel image... OK!
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (sebkinne@Worker) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48411) ) #17 Wed Feb 10 21:08:28 PST 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125796K/131072K available (2642K kernel code, 125K rwdata, 556K rodata, 188K init, 186K bss, 5276K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is tetra
[ 0.530000] registering PCI controller with io_map_base unset
[ 0.540000] PCI host bridge to bus 0000:00
[ 0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.550000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.560000] pci 0000:00:00.0: invalid calibration data
[ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.570000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switched to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.590000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.600000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.600000] TCP: reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.650000] msgmni has been set to 245
[ 0.660000] io scheduler noop registered
[ 0.670000] io scheduler deadline registered (default)
[ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.680000] console [ttyS0] disabled
ú[ 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.710000] console [ttyS0] enabled
[ 0.710000] console [ttyS0] enabled
[ 0.720000] bootconsole [early0] disabled
[ 0.720000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found s25fl008k, expected m25p80
[ 0.730000] m25p80 spi0.0: s25fl008k (1024 Kbytes)
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.750000] 0x000000040000-0x000000080000 : "u-boot-env"
[ 0.760000] 0x000000080000-0x0000000c0000 : "caldata"
[ 0.760000] 0x0000000c0000-0x000000100000 : "mb0"
[ 0.770000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48
[ 0.780000] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit
[ 0.780000] nand: 2048MiB, SLC, page size: 4096, OOB size: 224
[ 0.790000] Scanning device for bad blocks
[ 1.070000] random: nonblocking pool is initialized
[ 1.070000] 2 cmdlinepart partitions found on MTD device ar934x-nfc
[ 1.080000] Creating 2 MTD partitions on "ar934x-nfc":
[ 1.080000] 0x000000000000-0x000000200000 : "kernel"
[ 1.090000] 0x000000200000-0x000080000000 : "ubi"
[ 1.110000] libphy: ag71xx_mdio: probed
[ 1.700000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.740000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.340000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.350000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.350000] TCP: cubic registered
[ 2.360000] NET: Registered protocol family 17
[ 2.360000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.380000] 8021q: 802.1Q VLAN Support v1.8
[ 2.380000] UBI: auto-attach mtd5
[ 2.390000] UBI: attaching mtd5 to ubi0
[ 14.070000] UBI: scanning is finished
[ 14.100000] UBI: attached mtd5 (name "ubi", size 2046 MiB) to ubi0
[ 14.110000] UBI: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes
[ 14.120000] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 14.120000] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 14.130000] UBI: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0
[ 14.140000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 14.140000] UBI: max/mean erase counter: 12/1, WL threshold: 4096, image sequence number: 858528783
[ 14.150000] UBI: available PEBs: 0, total reserved PEBs: 4092, PEBs reserved for bad PEB handling: 80
[ 14.160000] UBI: background thread "ubi_bgt0d" started, PID 236
[ 14.170000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 14.170000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 14.190000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 14.200000] Freeing unused kernel memory: 188K (803a1000 - 803d0000)
[ 15.740000] init: Console is alive
[ 15.750000] init: - watchdog -
[ 17.670000] usbcore: registered new interface driver usbfs
[ 17.670000] usbcore: registered new interface driver hub
[ 17.680000] usbcore: registered new device driver usb
[ 17.730000] SCSI subsystem initialized
[ 17.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.750000] ehci-platform: EHCI generic platform driver
[ 17.750000] ehci-platform ehci-platform: EHCI Host Controller
[ 17.760000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 17.770000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 17.790000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 17.790000] hub 1-0:1.0: USB hub found
[ 17.800000] hub 1-0:1.0: 1 port detected
[ 17.800000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 17.810000] ohci-platform: OHCI generic platform driver
[ 17.820000] uhci_hcd: USB Universal Host Controller Interface driver
[ 17.830000] usbcore: registered new interface driver usb-storage
[ 17.860000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 22.460000] mount_root: loading kmods from internal overlay
[ 22.860000] UBIFS: background thread "ubifs_bgt0_1" started, PID 348
[ 23.200000] UBIFS: recovery needed
[ 24.010000] UBIFS: recovery completed
[ 24.010000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 24.020000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 24.030000] UBIFS: FS size: 2049417216 bytes (1954 MiB, 3971 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 24.040000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 24.040000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8C60326B-568B-489B-A7AB-C1381DB3E862, small LPT model
[ 24.060000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 24.080000] block: extroot: not configured
[ 24.090000] UBIFS: un-mount UBI device 0, volume 1
[ 24.090000] UBIFS: background thread "ubifs_bgt0_1" stops
[ 24.110000] UBIFS: background thread "ubifs_bgt0_1" started, PID 351
[ 24.970000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 24.970000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 24.980000] UBIFS: FS size: 2049417216 bytes (1954 MiB, 3971 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 24.990000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 25.000000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8C60326B-568B-489B-A7AB-C1381DB3E862, small LPT model
[ 25.020000] mount_root: loading kmods from internal overlay
[ 25.250000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 25.270000] block: extroot: not configured
[ 25.280000] mount_root: switching to jffs2 overlay
[ 25.360000] procd: - early -
[ 25.360000] procd: - watchdog -
[ 26.460000] procd: - ubus -
[ 27.520000] procd: - init -
Please press Enter to activate this console.
[ 29.790000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 29.800000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 29.820000] cfg80211: Calling CRDA to update world regulatory domain
[ 29.850000] cfg80211: World regulatory domain updated:
[ 29.850000] cfg80211: DFS Master region: unset
[ 29.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 29.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 29.870000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 29.880000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 29.890000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 29.900000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 29.910000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 29.920000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 29.930000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 30.040000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 30.050000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 30.060000] cfg80211: Calling CRDA for country: US
[ 30.060000] cfg80211: Regulatory domain changed to country: US
[ 30.070000] cfg80211: DFS Master region: FCC
[ 30.070000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 30.080000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 30.090000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 30.100000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 30.110000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[ 30.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 30.130000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 30.160000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 30.180000] usbcore: registered new interface driver ath9k_htc
[ 30.210000] RPC: Registered named UNIX socket transport module.
[ 30.220000] RPC: Registered udp transport module.
[ 30.220000] RPC: Registered tcp transport module.
[ 30.230000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 30.260000] tun: Universal TUN/TAP device driver, 1.6
[ 30.260000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 30.490000] usbcore: registered new interface driver rt2800usb
[ 30.500000] usbcore: registered new interface driver rtl8187
[ 30.540000] usbcore: registered new interface driver rtl8192cu
[ 30.600000] usbcore: registered new interface driver cdc_acm
[ 30.600000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 30.610000] usbcore: registered new interface driver cdc_wdm
[ 30.630000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 30.690000] usbcore: registered new interface driver ums-alauda
[ 30.690000] usbcore: registered new interface driver ums-cypress
[ 30.700000] usbcore: registered new interface driver ums-datafab
[ 30.710000] usbcore: registered new interface driver ums-freecom
[ 30.730000] usbcore: registered new interface driver ums-isd200
[ 30.740000] usbcore: registered new interface driver ums-jumpshot
[ 30.750000] usbcore: registered new interface driver ums-karma
[ 30.760000] usbcore: registered new interface driver ums-sddr09
[ 30.770000] usbcore: registered new interface driver ums-sddr55
[ 30.780000] usbcore: registered new interface driver ums-usbat
[ 30.800000] usbcore: registered new interface driver usbserial
[ 30.800000] usbcore: registered new interface driver usbserial_generic
[ 30.810000] usbserial: USB Serial support registered for generic
[ 30.890000] xt_time: kernel timezone is -0000
[ 30.900000] usbcore: registered new interface driver asix
[ 30.910000] usbcore: registered new interface driver cdc_ether
[ 30.920000] ip_tables: © 2000-2006 Netfilter Core Team
[ 30.960000] usbcore: registered new interface driver pl2303
[ 30.960000] usbserial: USB Serial support registered for pl2303
[ 30.980000] PPP generic driver version 2.4.2
[ 30.980000] NET: Registered protocol family 24
[ 30.990000] usbcore: registered new interface driver qmi_wwan
[ 31.000000] usbcore: registered new interface driver rndis_host
[ 31.010000] usbcore: registered new interface driver sierra_net
[ 31.020000] usbcore: registered new interface driver option
[ 31.030000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 41.050000] device eth1 entered promiscuous mode
[ 41.070000] br-lan: port 1(eth1) entered forwarding state
[ 41.070000] br-lan: port 1(eth1) entered forwarding state
[ 41.140000] br-lan: port 1(eth1) entered disabled state
[ 43.960000] eth1: link up (100Mbps/Full duplex)
[ 43.960000] br-lan: port 1(eth1) entered forwarding state
[ 43.970000] br-lan: port 1(eth1) entered forwarding state
[ 45.830000] device wlan0 entered promiscuous mode
[ 45.830000] br-lan: port 2(wlan0) entered forwarding state
[ 45.840000] br-lan: port 2(wlan0) entered forwarding state
[ 45.940000] device wlan0-1 entered promiscuous mode
[ 45.950000] br-lan: port 3(wlan0-1) entered forwarding state
[ 45.950000] br-lan: port 3(wlan0-1) entered forwarding state
[ 45.970000] br-lan: port 1(eth1) entered forwarding state
[ 46.350000] br-lan: port 3(wlan0-1) entered disabled state
[ 47.090000] br-lan: port 3(wlan0-1) entered forwarding state
[ 47.090000] br-lan: port 3(wlan0-1) entered forwarding state
[ 47.840000] br-lan: port 2(wlan0) entered forwarding state
[ 49.090000] br-lan: port 3(wlan0-1) entered forwarding state
[ 61.390000] device wlan1mon entered promiscuous mode
U-Boot 1.1.4 (Dec 22 2015 - 12:54:58)
DB120
DRAM:
sri
Wasp 1.2
wasp_ddr_initial_config(249): (32bit) ddr2 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf [0x0 - 0x1f]
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 276k for U-Boot at: 87fb8000
Reserving 192k for malloc() at: 87f88000
Reserving 44 Bytes for Board Info at: 87f87fd4
Reserving 36 Bytes for Global Data at: 87f87fb0
Reserving 128k for boot params() at: 87f67fb0
Stack Pointer at: 87f67f98
Now running in RAM - U-Boot at: 87fb8000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x14
flash size 1MB, sector count = 16
Flash: 1 MB
*** Warning - bad CRC, using default environment
Now starting pci_init process
pci_init_board: PCIe PLL not set for 40MHz refclk
BOARD IS NOT CALIBRATED!!!
pci_init finished
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
wasp reset mask:c02200
WASP ----> S27 PHY
s27 reg init
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
WASP ----> S27 PHY
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Atheros on-chip NAND FLash Controller Driver, Version 0.1 © 2010 Atheros Communications, Ltd.
Ath Nand ID[87fef17c]: 2c:48:00:26:89
ONFI MICRON MT29F16G08ABABAWP
Micronset ns -0x80000-0x1000
====== NAND Parameters ======
sc = 0x87fef158 bbt = 0x87f98538 bbt_size = 0x400 nf_ctrl = 0x485
page = 0x1000 block = 0x80000 oob = 0xe0
size = 2048MB
Setting 0xb8116290 to 0x20402d0f
Hit any key to stop autoboot: 2 1 0
Loading from device 0: ath-nand (offset 0x0)
Booting image at: 0x81000000
Image Name: MIPS OpenWrt Linux-3.18.23
Created: 2016-02-11 5:08:33 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1965951 Bytes = 1.9 MB
Load Address: 80060000
Entry Point: 80060000
Uncompressing kernel image... OK!
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (sebkinne@Worker) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48411) ) #17 Wed Feb 10 21:08:28 PST 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125796K/131072K available (2642K kernel code, 125K rwdata, 556K rodata, 188K init, 186K bss, 5276K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is tetra
[ 0.530000] registering PCI controller with io_map_base unset
[ 0.540000] PCI host bridge to bus 0000:00
[ 0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.550000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.560000] pci 0000:00:00.0: invalid calibration data
[ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.570000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switched to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.590000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.600000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.600000] TCP: reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.660000] msgmni has been set to 245
[ 0.660000] io scheduler noop registered
[ 0.670000] io scheduler deadline registered (default)
[ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.680000] console [ttyS0] disabled
ú[ 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.710000] console [ttyS0] enabled
[ 0.710000] console [ttyS0] enabled
[ 0.720000] bootconsole [early0] disabled
[ 0.720000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found s25fl008k, expected m25p80
[ 0.730000] m25p80 spi0.0: s25fl008k (1024 Kbytes)
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.750000] 0x000000040000-0x000000080000 : "u-boot-env"
[ 0.760000] 0x000000080000-0x0000000c0000 : "caldata"
[ 0.760000] 0x0000000c0000-0x000000100000 : "mb0"
[ 0.770000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48
[ 0.780000] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit
[ 0.780000] nand: 2048MiB, SLC, page size: 4096, OOB size: 224
[ 0.790000] Scanning device for bad blocks
[ 1.060000] random: nonblocking pool is initialized
[ 1.070000] 2 cmdlinepart partitions found on MTD device ar934x-nfc
[ 1.080000] Creating 2 MTD partitions on "ar934x-nfc":
[ 1.080000] 0x000000000000-0x000000200000 : "kernel"
[ 1.090000] 0x000000200000-0x000080000000 : "ubi"
[ 1.100000] libphy: ag71xx_mdio: probed
[ 1.700000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.740000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.340000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.350000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.350000] TCP: cubic registered
[ 2.360000] NET: Registered protocol family 17
[ 2.360000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.380000] 8021q: 802.1Q VLAN Support v1.8
[ 2.380000] UBI: auto-attach mtd5
[ 2.390000] UBI: attaching mtd5 to ubi0
[ 14.070000] UBI: scanning is finished
[ 14.100000] UBI: attached mtd5 (name "ubi", size 2046 MiB) to ubi0
[ 14.110000] UBI: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes
[ 14.120000] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 14.120000] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 14.130000] UBI: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0
[ 14.140000] UBI: user volume: 2, internal volumes: 1,

Edited by bored369
Link to comment
Share on other sites

Tried testing with the Anker PowerCore 20100 replacing the Pineapple 15000 for both the y-cable ports (each port getting 2.4a), same UART to rasPi2 otherwise.

It appeared to stay on and not reboot automatically after starting PineAP red light flashing.

So I connected to the management AP and tried doing a recon scan for 1 minute. This caused a reboot after this message was displayed about 50 % through the scan (also the red light went solid for a moment then the tetra rebooted)

[ 50.790000] br-lan: port 3(wlan0-1) entered forwarding state
[ 61.970000] device wlan1mon entered promiscuous mode
[ 329.120000] ath: phy0: Unable to reset channel, reset status -5
The full output from that run is the following:

Script started on Thu Feb 18 07:42:28 2016
root@kali:~# screen /dev/ttyUSB0 115200 8N1
[r[m[2J[H[?7h[?1;4;6l[?1049h[4l[?1h=[0m(B[1;24r[H[2J[H[2J^Eú[ 22.460000] mount_root: loading kmods from internal overlay
[ 22.860000] UBIFS: background thread "ubifs_bgt0_1" started, PID 348
[ 23.320000] UBIFS: recovery needed
[ 24.110000] UBIFS: recovery completed
[ 24.120000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 24.120000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 24.130000] UBIFS: FS size: 2049417216 bytes (1954 MiB, 3971 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 24.140000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 24.150000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8C60326B-568B-489B-A7AB-C1381DB3E862, small LPT model
[ 24.160000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 24.190000] block: extroot: not configured
[ 24.200000] UBIFS: un-mount UBI device 0, volume 1
[ 24.200000] UBIFS: background thread "ubifs_bgt0_1" stops
[ 24.210000] UBIFS: background thread "ubifs_bgt0_1" started, PID 351
[ 25.170000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 25.180000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 25.190000] UBIFS: FS size: 2049417216 bytes (1954 MiB, 3971 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 25.200000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 25.200000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8C60326B-568B-489B-A7AB-C1381DB3E862, small LPT model
[ 25.220000] mount_root: loading kmods from internal overlay
[ 25.450000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 25.470000] block: extroot: not configured
[ 25.480000] mount_root: switching to jffs2 overlay
[ 25.560000] procd: - early -
[ 25.570000] procd: - watchdog -
[ 26.660000] procd: - ubus -
Command failed: Not found
[ 27.710000] procd: - init -
Please press Enter to activate this console.
Command failed: Not found
Command failed: Not found
Command failed: Not found
Command failed: Not found
[ 30.000000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 30.010000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 30.030000] cfg80211: Calling CRDA to update world regulatory domain
[ 30.040000] cfg80211: World regulatory domain updated:
[ 30.050000] cfg80211: DFS Master region: unset
[ 30.050000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 30.060000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.070000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 30.080000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.090000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 30.100000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 30.110000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 30.110000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.120000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 30.250000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 30.260000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 30.270000] cfg80211: Calling CRDA for country: US
[ 30.270000] cfg80211: Regulatory domain changed to country: US
[ 30.280000] cfg80211: DFS Master region: FCC
[ 30.280000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 30.290000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 30.300000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 30.310000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 30.320000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[ 30.330000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 30.330000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 30.370000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 30.390000] usbcore: registered new interface driver ath9k_htc
[ 30.420000] RPC: Registered named UNIX socket transport module.
[ 30.430000] RPC: Registered udp transport module.
[ 30.440000] RPC: Registered tcp transport module.
[ 30.440000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 30.460000] tun: Universal TUN/TAP device driver, 1.6
[ 30.470000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 30.680000] usbcore: registered new interface driver rt2800usb
[ 30.700000] usbcore: registered new interface driver rtl8187
[ 30.730000] usbcore: registered new interface driver rtl8192cu
[ 30.780000] usbcore: registered new interface driver cdc_acm
[ 30.780000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 30.800000] usbcore: registered new interface driver cdc_wdm
[ 30.810000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 30.890000] usbcore: registered new interface driver ums-alauda
[ 30.890000] usbcore: registered new interface driver ums-cypress
[ 30.900000] usbcore: registered new interface driver ums-datafab
[ 30.910000] usbcore: registered new interface driver ums-freecom
[ 30.930000] usbcore: registered new interface driver ums-isd200
[ 30.940000] usbcore: registered new interface driver ums-jumpshot
[ 30.950000] usbcore: registered new interface driver ums-karma
[ 30.960000] usbcore: registered new interface driver ums-sddr09
[ 30.970000] usbcore: registered new interface driver ums-sddr55
[ 30.980000] usbcore: registered new interface driver ums-usbat
[ 31.000000] usbcore: registered new interface driver usbserial
[ 31.000000] usbcore: registered new interface driver usbserial_generic
[ 31.010000] usbserial: USB Serial support registered for generic
[ 31.090000] xt_time: kernel timezone is -0000
[ 31.100000] usbcore: registered new interface driver asix
[ 31.110000] usbcore: registered new interface driver cdc_ether
[ 31.120000] ip_tables: © 2000-2006 Netfilter Core Team
[ 31.160000] usbcore: registered new interface driver pl2303
[ 31.170000] usbserial: USB Serial support registered for pl2303
[ 31.180000] PPP generic driver version 2.4.2
[ 31.180000] NET: Registered protocol family 24
[ 31.190000] usbcore: registered new interface driver qmi_wwan
[ 31.200000] usbcore: registered new interface driver rndis_host
[ 31.210000] usbcore: registered new interface driver sierra_net
[ 31.220000] usbcore: registered new interface driver option
[ 31.230000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 41.380000] device eth1 entered promiscuous mode
[ 41.390000] br-lan: port 1(eth1) entered forwarding state
[ 41.390000] br-lan: port 1(eth1) entered forwarding state
[ 42.470000] br-lan: port 1(eth1) entered disabled state
[ 44.510000] eth1: link up (100Mbps/Full duplex)
[ 44.530000] br-lan: port 1(eth1) entered forwarding state
[ 44.530000] br-lan: port 1(eth1) entered forwarding state
[ 46.530000] br-lan: port 1(eth1) entered forwarding state
[ 46.970000] device wlan0 entered promiscuous mode
[ 47.030000] br-lan: port 2(wlan0) entered forwarding state
[ 47.040000] br-lan: port 2(wlan0) entered forwarding state
[ 47.090000] device wlan0-1 entered promiscuous mode
[ 47.100000] br-lan: port 3(wlan0-1) entered forwarding state
[ 47.100000] br-lan: port 3(wlan0-1) entered forwarding state
[ 47.780000] br-lan: port 3(wlan0-1) entered disabled state
[ 48.790000] br-lan: port 3(wlan0-1) entered forwarding state
[ 48.790000] br-lan: port 3(wlan0-1) entered forwarding state
[ 49.040000] br-lan: port 2(wlan0) entered forwarding state
[ 50.790000] br-lan: port 3(wlan0-1) entered forwarding state
[ 61.970000] device wlan1mon entered promiscuous mode
[ 329.120000] ath: phy0: Unable to reset channel, reset status -5
U-Boot 1.1.4 (Dec 22 2015 - 12:54:58)
DB120
DRAM:
sri
Wasp 1.2
wasp_ddr_initial_config(249): (32bit) ddr2 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xf [0x0 - 0x1f]
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 276k for U-Boot at: 87fb8000
Reserving 192k for malloc() at: 87f88000
Reserving 44 Bytes for Board Info at: 87f87fd4
Reserving 36 Bytes for Global Data at: 87f87fb0
Reserving 128k for boot params() at: 87f67fb0
Stack Pointer at: 87f67f98
Now running in RAM - U-Boot at: 87fb8000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x14
flash size 1MB, sector count = 16
Flash: 1 MB
*** Warning - bad CRC, using default environment
Now starting pci_init process
pci_init_board: PCIe PLL not set for 40MHz refclk
BOARD IS NOT CALIBRATED!!!
pci_init finished
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
wasp reset mask:c02200
WASP ----> S27 PHY
s27 reg init
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :12
eth0 up
WASP ----> S27 PHY
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Atheros on-chip NAND FLash Controller Driver, Version 0.1 © 2010 Atheros Communications, Ltd.
Ath Nand ID[87fef17c]: 2c:48:00:26:89
ONFI MICRON MT29F16G08ABABAWP
Micronset ns -0x80000-0x1000
====== NAND Parameters ======
sc = 0x87fef158 bbt = 0x87f98538 bbt_size = 0x400 nf_ctrl = 0x485
page = 0x1000 block = 0x80000 oob = 0xe0
size = 2048MB
Setting 0xb8116290 to 0x20402d0f
Hit any key to stop autoboot: 2 1 0
Loading from device 0: ath-nand (offset 0x0)
Booting image at: 0x81000000
Image Name: MIPS OpenWrt Linux-3.18.23
Created: 2016-02-11 5:08:33 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1965951 Bytes = 1.9 MB
Load Address: 80060000
Entry Point: 80060000
Uncompressing kernel image... OK!
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (sebkinne@Worker) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48411) ) #17 Wed Feb 10 21:08:28 PST 2016
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TETRA console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,256k(u-boot-env),256k(caldata),-(mb0);ar934x-nfc:2048k(kernel),-(ubi) rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125796K/131072K available (2642K kernel code, 125K rwdata, 556K rodata, 188K init, 186K bss, 5276K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:40.000MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is tetra
[ 0.530000] registering PCI controller with io_map_base unset
[ 0.540000] PCI host bridge to bus 0000:00
[ 0.540000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.550000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.550000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.560000] pci 0000:00:00.0: invalid calibration data
[ 0.560000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.570000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.570000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.580000] Switched to clocksource MIPS
[ 0.580000] NET: Registered protocol family 2
[ 0.590000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.590000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.600000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.600000] TCP: reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] NET: Registered protocol family 1
[ 0.620000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.650000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.650000] msgmni has been set to 245
[ 0.660000] io scheduler noop registered
[ 0.660000] io scheduler deadline registered (default)
[ 0.660000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.670000] console [ttyS0] disabled
þ[ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.700000] console [ttyS0] enabled
[ 0.700000] console [ttyS0] enabled
[ 0.710000] bootconsole [early0] disabled
[ 0.710000] bootconsole [early0] disabled
[ 0.730000] m25p80 spi0.0: found s25fl008k, expected m25p80
[ 0.730000] m25p80 spi0.0: s25fl008k (1024 Kbytes)
[ 0.740000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 4 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.750000] 0x000000040000-0x000000080000 : "u-boot-env"
[ 0.760000] 0x000000080000-0x0000000c0000 : "caldata"
[ 0.770000] 0x0000000c0000-0x000000100000 : "mb0"
[ 0.770000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48
[ 0.780000] nand: Micron MT29F16G08ABABAWP 2GiB 3.3V 8-bit
[ 0.790000] nand: 2048MiB, SLC, page size: 4096, OOB size: 224
[ 0.790000] Scanning device for bad blocks
[ 1.070000] random: nonblocking pool is initialized
[ 1.070000] 2 cmdlinepart partitions found on MTD device ar934x-nfc
[ 1.080000] Creating 2 MTD partitions on "ar934x-nfc":
[ 1.080000] 0x000000000000-0x000000200000 : "kernel"
[ 1.090000] 0x000000200000-0x000080000000 : "ubi"
[ 1.110000] libphy: ag71xx_mdio: probed
[ 1.700000] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.740000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.340000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[ 2.350000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.350000] TCP: cubic registered
[ 2.360000] NET: Registered protocol family 17
[ 2.360000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.380000] 8021q: 802.1Q VLAN Support v1.8
[ 2.380000] UBI: auto-attach mtd5
[ 2.390000] UBI: attaching mtd5 to ubi0
[ 14.070000] UBI: scanning is finished
[ 14.100000] UBI: attached mtd5 (name "ubi", size 2046 MiB) to ubi0
[ 14.110000] UBI: PEB size: 524288 bytes (512 KiB), LEB size: 516096 bytes
[ 14.120000] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
[ 14.120000] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
[ 14.130000] UBI: good PEBs: 4092, bad PEBs: 0, corrupted PEBs: 0
[ 14.140000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 14.140000] UBI: max/mean erase counter: 12/1, WL threshold: 4096, image sequence number: 858528783
[ 14.150000] UBI: available PEBs: 0, total reserved PEBs: 4092, PEBs reserved for bad PEB handling: 80
[ 14.160000] UBI: background thread "ubi_bgt0d" started, PID 236
[ 14.170000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 14.170000] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 14.190000] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 14.200000] Freeing unused kernel memory: 188K (803a1000 - 803d0000)
[ 15.740000] init: Console is alive
[ 15.750000] init: - watchdog -
[ 17.670000] usbcore: registered new interface driver usbfs
[ 17.680000] usbcore: registered new interface driver hub
[ 17.680000] usbcore: registered new device driver usb
[ 17.730000] SCSI subsystem initialized
[ 17.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.740000] ehci-platform: EHCI generic platform driver
[ 17.750000] ehci-platform ehci-platform: EHCI Host Controller
[ 17.760000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 17.770000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 17.790000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 17.790000] hub 1-0:1.0: USB hub found
[ 17.800000] hub 1-0:1.0: 1 port detected
[ 17.800000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 17.810000] ohci-platform: OHCI generic platform driver
[ 17.820000] uhci_hcd: USB Universal Host Controller Interface driver
[ 17.830000] usbcore: registered new interface driver usb-storage
[ 17.860000] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 22.460000] mount_root: loading kmods from internal overlay
[ 22.860000] UBIFS: background thread "ubifs_bgt0_1" started, PID 348
[ 23.310000] UBIFS: recovery needed
[ 24.110000] UBIFS: recovery completed
[ 24.120000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 24.130000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 24.130000] UBIFS: FS size: 2049417216 bytes (1954 MiB, 3971 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 24.150000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 24.150000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8C60326B-568B-489B-A7AB-C1381DB3E862, small LPT model
[ 24.160000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 24.190000] block: extroot: not configured
[ 24.190000] UBIFS: un-mount UBI device 0, volume 1
[ 24.200000] UBIFS: background thread "ubifs_bgt0_1" stops
[ 24.210000] UBIFS: background thread "ubifs_bgt0_1" started, PID 351
[ 25.160000] UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 25.170000] UBIFS: LEB size: 516096 bytes (504 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes
[ 25.180000] UBIFS: FS size: 2049417216 bytes (1954 MiB, 3971 LEBs), journal size 33546240 bytes (31 MiB, 65 LEBs)
[ 25.190000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 25.190000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 8C60326B-568B-489B-A7AB-C1381DB3E862, small LPT model
[ 25.220000] mount_root: loading kmods from internal overlay
[ 25.440000] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 25.460000] block: extroot: not configured
[ 25.470000] mount_root: switching to jffs2 overlay
[ 25.550000] procd: - early -
[ 25.560000] procd: - watchdog -
[ 26.650000] procd: - ubus -
[ 27.700000] procd: - init -
Please press Enter to activate this console.
[ 29.990000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 30.000000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 30.030000] cfg80211: Calling CRDA to update world regulatory domain
[ 30.030000] cfg80211: World regulatory domain updated:
[ 30.040000] cfg80211: DFS Master region: unset
[ 30.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 30.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.060000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 30.070000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.080000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 30.090000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 30.100000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 30.110000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.110000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 30.240000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 30.250000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 30.260000] cfg80211: Calling CRDA for country: US
[ 30.260000] cfg80211: Regulatory domain changed to country: US
[ 30.270000] cfg80211: DFS Master region: FCC
[ 30.270000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 30.280000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 30.290000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 30.300000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 30.310000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (0 s)
[ 30.320000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 30.330000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 30.360000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 30.380000] usbcore: registered new interface driver ath9k_htc
[ 30.410000] RPC: Registered named UNIX socket transport module.
[ 30.420000] RPC: Registered udp transport module.
[ 30.420000] RPC: Registered tcp transport module.
[ 30.430000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 30.450000] tun: Universal TUN/TAP device driver, 1.6
[ 30.450000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 30.680000] usbcore: registered new interface driver rt2800usb
[ 30.690000] usbcore: registered new interface driver rtl8187
[ 30.730000] usbcore: registered new interface driver rtl8192cu
[ 30.790000] usbcore: registered new interface driver cdc_acm
[ 30.790000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 30.800000] usbcore: registered new interface driver cdc_wdm
[ 30.820000] nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
[ 30.880000] usbcore: regist
Edited by bored369
Link to comment
Share on other sites

That's pretty much all greek to me, but appreciate learning how to get to the serial console!

Hope that helps track something down.

I should have a second y-cable tomorrow then I can try hooking up even more juice to it while it's connected to the rasPi2 and do some more testing if that would help any.

Let me know if there is any other testing I can do.

Link to comment
Share on other sites

We need to mainly be testing it with just the 2 pineapple 15000 batteries as the set comes. No use to add extra battery if we notice it's being unstable ;) with the provided items

I know I was just testing the outcome with additional power added to the mix :) There was a change, so it may prove helpful.

Link to comment
Share on other sites

Please use spoiler tags for your logs ^_^

which button is that or how would on go about that? I'm not very forum savvy.

Also noticed I was still on 1.0.1 firmware, just updated to 1.0.2 and with the anker battery pack setup (2.4a to each y-cable and rasPi2 usb port on standard cable) didn't see the power loss issue, with recon or anything else I tried.

Using 1.0.2 with Pineapple 15000 on the each of the y-cable (so 1a and 2.1a) and rasPi2 usb port, it still does the rebooting as soon as pineap seems to start up.

using 1.0.2 with two pineapple 15000 on each of the y-cable (so 2.1a and 2.1a) and rasPi2 usb port, it does not do the rebooting even with recon and anything else i tried.

Link to comment
Share on other sites

now if only we can find out why loss of power using two pineapple batteries when under load aka just using pineap :) is there like a rest state on the batteries itself that it will just go into sleep.i did notice one battery where the orange leds would just turn off

That's exactly what happens to me. One of the batteries just turns off when I try to recon.

Link to comment
Share on other sites

What does this mean on the logs: Warning - bad CRC, using default environment

Now starting pci_init process

pci_init_board: PCIe PLL not set for 40MHz refclk

BOARD IS NOT CALIBRATED!!!

pci_init finished

While I can't tell you why its there, I've been told its normal and nothing to worry about

Edited by Foxtrot
Link to comment
Share on other sites

So I got the 2amp 12v adapter today and had no issues with using that, worked for a few hours doing recon scans every now and then. Also got my second y-cable and I have four batteries hooked up to it (I want the longest runtime I can get) and everything seems to be working great with that so far.

IfjNtZr.jpg

  • Upvote 1
Link to comment
Share on other sites

So I got the 2amp 12v adapter today and had no issues with using that, worked for a few hours doing recon scans every now and then. Also got my second y-cable and I have four batteries hooked up to it (I want the longest runtime I can get) and everything seems to be working great with that so far.

IfjNtZr.jpg

I figured it was power related! :)

  • Upvote 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...