3G dongle Alcatel X602A recognized but missing confs.

[kavastudios]

Hi.

I am trying to use a 3G usb Dongle Alcatel X602A.

When I run lsusb I've got this:

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Bus 001 Device 002: ID 058f:6254 Alcor Micro Corp. USB Hub

Bus 001 Device 003: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter

Bus 001 Device 006: ID 1bbb:022c T & A Mobile Phones

Bus 001 Device 005: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader

It's recognized as Bus 001 Device 006: ID 1bbb:022c T & A Mobile Phones

I've checked the usb-modeswitch-data package and it show the 1bbb:022c file with the following info (i've downloaded the tar from the website):

#Alcatel X602D

Configuration=2

Then I cheked in /etc/usb_modeswitch.d/ in my router but the file 1bbb:022c was missing, so I've created the file with the info above mentioned.

Now when I run the lsusb I've got the same but if i run dmesg I get:

[ 22.170000] scsi 2:0:0:0: CD-ROM USBModem Mass Storage 2.31 PQ: 0 ANSI: 2

[ 38.240000] usbcore: registered new interface driver cdc_acm

[ 38.250000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters

[ 38.470000] usbcore: registered new interface driver usbserial

[ 38.480000] USB Serial support registered for generic

[ 38.480000] usbcore: registered new interface driver usbserial_generic

[ 38.490000] usbserial: USB Serial Driver core

[ 38.630000] usbcore: registered new interface driver asix

[ 38.710000] usbcore: registered new interface driver cdc_ether

[ 38.950000] Error: Driver 'gpio-keys-polled' is already registered, aborting...

[ 39.050000] usbcore: registered new interface driver rndis_host

[ 39.160000] sd 1:0:0:0: Attached scsi generic sg0 type 0

[ 39.170000] scsi 2:0:0:0: Attached scsi generic sg1 type 5

[ 39.190000] USB Serial support registered for GSM modem (1-port)

[ 39.200000] usbcore: registered new interface driver option

[ 39.200000] option: v0.7.2:USB Driver for GSM modems

Also, when I run

cat /proc/bus/usb/devices

I get this:

T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#= 6 Spd=480 MxCh= 0

D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 2

P: Vendor=1bbb ProdID=022c Rev= 0.00

S: Manufacturer=SCD

S: Product=HSPA+ USB Modem

C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=250mA

I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=

E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

C:* #Ifs= 4 Cfg#= 2 Atr=80 MxPwr=200mA

I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)

E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)

E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)

E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)

E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

I am a bit lost, I don't know if the 3g dongle was properly switched and to which /dev/ was attached?

What i am missing?

Thanks in advance for any guidance.

Edited November 5, 2015 by kavastudios