ZeroSec Posted August 7, 2014 Share Posted August 7, 2014 Hey guys! I just got a USB 4G LTE Novatel U679 and have been trying to set it up with my pineapple, I have my settings as follows: network.wan2=interface network.wan2.ifname=ppp0 network.wan2.proto=3g network.wan2.service=umts network.wan2.device=/dev/ttyUSB0 network.wan2.apn=inet.bell.ca network.wan2.username= network.wan2.password= network.wan2.defaultroute=1 network.wan2.ppp_redial=persist network.wan2.peerdns=1 network.wan2.dns=8.8.8.8 network.wan2.keepalive=1 network.wan2.pppd_options=debug And this is not working. The odd thing is that when I first plug it into my pineapple the led ON THE STICK flashes for 10-20 seconds, then just goes out. whereas when it is plugged into my computer (even if not connected to a network) it is always on. Also I have tried nearly every "service" to no success, could it be that the stick is 4g and the "protocol" is 3g? I know this isn't a "supported" device. But I would appreciate any help you guys can give me :) Quote Link to comment Share on other sites More sharing options...
Foxtrot Posted August 7, 2014 Share Posted August 7, 2014 Post the output of "dmesg" into spoiler tags here Quote Link to comment Share on other sites More sharing options...
Smarty Posted August 8, 2014 Share Posted August 8, 2014 Could also be a power issue. MK5 puts out 0.5A on the usb port. If your 4G stick draws more it will fail. Dont use battery power on the MK5 while testing and possibly try it with a powered usb hub.. (Just make shure the hub doesnt backfeed power to the MK5) Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted August 10, 2014 Author Share Posted August 10, 2014 (edited) Post the output of "dmesg" into spoiler tags here root@Pineapple:~# dmesg [ 0.000000] Linux version 3.3.8 (sebkinne@WorstationMeltdown) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #21 Fri May 23 22:17:04 CEST 2014 [ 0.000000] MyLoader: sysp=97d936c9, boardp=61b798de, parts=6238a85e [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802d8470, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=MK5 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61592k/65536k available (2124k kernel code, 3944k reserved, 406k data, 212k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79 [ 0.100000] MIPS: machine is MK5 V1.0 [ 0.350000] bio: create slab <bio-0> at 0 [ 0.360000] Switching to clocksource MIPS [ 0.360000] NET: Registered protocol family 2 [ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.370000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.370000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.380000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.390000] TCP reno registered [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] NET: Registered protocol family 1 [ 0.410000] PCI: CLS 0 bytes, default 32 [ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.440000] msgmni has been set to 120 [ 0.440000] io scheduler noop registered [ 0.450000] io scheduler deadline registered (default) [ 0.450000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART [ 0.470000] console [ttyATH0] enabled, bootconsole disabled [ 0.480000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.480000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.490000] 5 tp-link partitions found on MTD device spi0.0 [ 0.490000] Creating 5 MTD partitions on "spi0.0": [ 0.500000] 0x000000000000-0x000000020000 : "u-boot" [ 0.510000] 0x000000020000-0x000000102744 : "kernel" [ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.520000] 0x000000102744-0x000000ff0000 : "rootfs" [ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.540000] mtd: partition "rootfs" set to be root filesystem [ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=C50000, len=3A0000 [ 0.550000] 0x000000c50000-0x000000ff0000 : "rootfs_data" [ 0.560000] 0x000000ff0000-0x000001000000 : "art" [ 0.570000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.590000] ag71xx_mdio: probed [ 0.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.160000] TCP cubic registered [ 1.160000] NET: Registered protocol family 17 [ 1.160000] Bridge firewalling registered [ 1.170000] 8021q: 802.1Q VLAN Support v1.8 [ 1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.180000] Freeing unused kernel memory: 212k freed [ 3.460000] Registered led device: mk5:red:wlan1 [ 3.460000] Registered led device: mk5:blue:wlan0 [ 3.470000] Registered led device: mk5:amber:lan [ 6.780000] JFFS2 notice: (421) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (1 unchecked, 5 orphan) and 43 of xref (0 dead, 27 orphan) found. [ 7.750000] SCSI subsystem initialized [ 8.050000] usbcore: registered new interface driver usbfs [ 8.060000] usbcore: registered new interface driver hub [ 8.060000] usbcore: registered new device driver usb [ 8.410000] eth0: link up (100Mbps/Full duplex) [ 8.610000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.610000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 8.620000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 8.660000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 8.680000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 8.680000] hub 1-0:1.0: USB hub found [ 8.680000] hub 1-0:1.0: 1 port detected [ 8.790000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.920000] uhci_hcd: USB Universal Host Controller Interface driver [ 9.040000] Initializing USB Mass Storage driver... [ 9.040000] usbcore: registered new interface driver usb-storage [ 9.050000] USB Mass Storage support registered. [ 9.150000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 9.300000] hub 1-1:1.0: USB hub found [ 9.300000] hub 1-1:1.0: 4 ports detected [ 9.580000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 9.800000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform [ 9.930000] scsi0 : usb-storage 1-1.2:1.0 [ 10.040000] usb 1-1.4: new high-speed USB device number 5 using ehci-platform [ 10.170000] scsi1 : usb-storage 1-1.4:1.0 [ 10.940000] scsi 0:0:0:0: CD-ROM NVTL Mass Storage 2.31 PQ: 0 ANSI: 2 [ 11.170000] scsi 1:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0 [ 11.790000] sd 1:0:0:0: [sda] 3686400 512-byte logical blocks: (1.88 GB/1.75 GiB) [ 11.790000] sd 1:0:0:0: [sda] Write Protect is off [ 11.800000] sd 1:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 11.800000] sd 1:0:0:0: [sda] No Caching mode page present [ 11.800000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 11.810000] sd 1:0:0:0: [sda] No Caching mode page present [ 11.820000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 11.830000] sda: sda1 sda2 [ 11.830000] sd 1:0:0:0: [sda] No Caching mode page present [ 11.840000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 11.840000] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 29.460000] eth0: link down [ 30.420000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d [ 30.430000] Backport generated by backports.git backports-20140124-0-g1256d3e [ 30.540000] cfg80211: Calling CRDA to update world regulatory domain [ 30.550000] cfg80211: World regulatory domain updated: [ 30.550000] cfg80211: DFS Master region: unset [ 30.560000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 30.570000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.570000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.580000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 30.590000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 30.600000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 30.610000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 32.100000] usbcore: registered new interface driver rt73usb [ 32.150000] ath: phy0: Enable LNA combining [ 32.150000] ath: EEPROM regdomain: 0x0 [ 32.150000] ath: EEPROM indicates default country code should be used [ 32.150000] ath: doing EEPROM country->regdmn map search [ 32.150000] ath: country maps to regdmn code: 0x3a [ 32.150000] ath: Country alpha2 being used: US [ 32.150000] ath: Regpair used: 0x3a [ 32.170000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 32.170000] Registered led device: ath9k-phy0 [ 32.170000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 32.180000] cfg80211: Calling CRDA for country: US [ 32.180000] cfg80211: Regulatory domain changed to country: US [ 32.180000] cfg80211: DFS Master region: FCC [ 32.190000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 32.200000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 32.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm) [ 32.210000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm) [ 32.220000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm) [ 32.230000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm) [ 32.240000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm) [ 32.240000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 32.530000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 32.530000] ieee80211 phy1: hwaddr 00:13:37:89:d0:3f, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2 [ 32.560000] rtl8187: Customer ID is 0x46 [ 32.560000] Registered led device: rtl8187-phy1::radio [ 32.560000] Registered led device: rtl8187-phy1::tx [ 32.560000] Registered led device: rtl8187-phy1::rx [ 32.560000] rtl8187: wireless switch is on [ 32.560000] usbcore: registered new interface driver rtl8187 [ 32.640000] Button Hotplug driver version 0.4.1 [ 32.860000] RPC: Registered named UNIX socket transport module. [ 32.860000] RPC: Registered udp transport module. [ 32.870000] RPC: Registered tcp transport module. [ 32.870000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 33.190000] PPP generic driver version 2.4.2 [ 33.220000] usbcore: registered new interface driver rt2800usb [ 33.350000] tun: Universal TUN/TAP device driver, 1.6 [ 33.360000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 33.710000] ip_tables: © 2000-2006 Netfilter Core Team [ 33.930000] NET: Registered protocol family 24 [ 34.080000] nf_conntrack version 0.5.0 (965 buckets, 3860 max) [ 34.780000] xt_time: kernel timezone is -0000 [ 35.300000] usbcore: registered new interface driver ath9k_htc [ 35.530000] usbcore: registered new interface driver usbserial [ 35.540000] USB Serial support registered for generic [ 35.540000] usbcore: registered new interface driver usbserial_generic [ 35.550000] usbserial: USB Serial Driver core [ 35.690000] usbcore: registered new interface driver asix [ 35.750000] usbcore: registered new interface driver cdc_ether [ 35.990000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 36.100000] usbcore: registered new interface driver rndis_host [ 36.200000] scsi 0:0:0:0: Attached scsi generic sg0 type 5 [ 36.210000] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 36.230000] USB Serial support registered for GSM modem (1-port) [ 36.240000] usbcore: registered new interface driver option [ 36.240000] option: v0.7.2:USB Driver for GSM modems [ 36.270000] USB Serial support registered for pl2303 [ 36.270000] usbcore: registered new interface driver pl2303 [ 36.270000] pl2303: Prolific PL2303 USB to serial adaptor driver [ 42.450000] usb 1-1.2: USB disconnect, device number 4 [ 43.380000] usb 1-1.2: new high-speed USB device number 6 using ehci-platform [ 43.510000] usb 1-1.2: config 1 has an invalid interface number: 6 but max is 5 [ 43.510000] usb 1-1.2: config 1 has an invalid interface number: 7 but max is 5 [ 43.520000] usb 1-1.2: config 1 has an invalid interface number: 7 but max is 5 [ 43.530000] usb 1-1.2: config 1 has no interface number 4 [ 43.530000] usb 1-1.2: config 1 has no interface number 5 [ 43.560000] cdc_ether 1-1.2:1.6: eth1: register 'cdc_ether' at usb-ehci-platform-1.2, CDC Ethernet Device, 00:a0:c6:00:00:00 [ 44.630000] device eth0 entered promiscuous mode [ 44.650000] cdc_ether 1-1.2:1.6: eth1: CDC: unexpected notification 01! [ 44.780000] eth0: link up (100Mbps/Full duplex) [ 44.780000] br-lan: port 1(eth0) entered forwarding state [ 44.790000] br-lan: port 1(eth0) entered forwarding state [ 46.790000] br-lan: port 1(eth0) entered forwarding state [ 50.510000] device wlan0 entered promiscuous mode [ 50.780000] eth0: link down [ 50.860000] br-lan: port 2(wlan0) entered forwarding state [ 50.860000] br-lan: port 2(wlan0) entered forwarding state [ 51.510000] br-lan: port 1(eth0) entered disabled state [ 52.860000] br-lan: port 2(wlan0) entered forwarding state [ 54.780000] eth0: link up (100Mbps/Full duplex) [ 54.780000] br-lan: port 1(eth0) entered forwarding state [ 54.790000] br-lan: port 1(eth0) entered forwarding state [ 56.790000] br-lan: port 1(eth0) entered forwarding state [ 61.240000] wlan1: authenticate with 38:60:77:88:57:3e [ 62.520000] wlan1: send auth to 38:60:77:88:57:3e (try 1/3) [ 62.520000] wlan1: authenticated [ 62.590000] wlan1: associate with 38:60:77:88:57:3e (try 1/3) [ 62.770000] wlan1: RX AssocResp from 38:60:77:88:57:3e (capab=0x411 status=0 aid=8) [ 62.800000] wlan1: associated [ 75.950000] FPU emulator disabled, make sure your toolchainwas compiled with software floating point support (soft-float) root@Pineapple:~# clear root@Pineapple:~# dmesg [ 0.000000] Linux version 3.3.8 (sebkinne@WorstationMeltdown) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #21 Fri May 23 22:17:04 CEST 2014 [ 0.000000] MyLoader: sysp=97d936c9, boardp=61b798de, parts=6238a85e [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802d8470, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=MK5 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61592k/65536k available (2124k kernel code, 3944k reserved, 406k data, 212k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79 [ 0.100000] MIPS: machine is MK5 V1.0 [ 0.350000] bio: create slab <bio-0> at 0 [ 0.360000] Switching to clocksource MIPS [ 0.360000] NET: Registered protocol family 2 [ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.370000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.370000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.380000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.390000] TCP reno registered [ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] NET: Registered protocol family 1 [ 0.410000] PCI: CLS 0 bytes, default 32 [ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.440000] msgmni has been set to 120 [ 0.440000] io scheduler noop registered [ 0.450000] io scheduler deadline registered (default) [ 0.450000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART [ 0.470000] console [ttyATH0] enabled, bootconsole disabled [ 0.480000] m25p80 spi0.0: found w25q128, expected m25p80 [ 0.480000] m25p80 spi0.0: w25q128 (16384 Kbytes) [ 0.490000] 5 tp-link partitions found on MTD device spi0.0 [ 0.490000] Creating 5 MTD partitions on "spi0.0": [ 0.500000] 0x000000000000-0x000000020000 : "u-boot" [ 0.510000] 0x000000020000-0x000000102744 : "kernel" [ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.520000] 0x000000102744-0x000000ff0000 : "rootfs" [ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.540000] mtd: partition "rootfs" set to be root filesystem [ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=C50000, len=3A0000 [ 0.550000] 0x000000c50000-0x000000ff0000 : "rootfs_data" [ 0.560000] 0x000000ff0000-0x000001000000 : "art" [ 0.570000] 0x000000020000-0x000000ff0000 : "firmware" [ 0.590000] ag71xx_mdio: probed [ 0.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY] [ 1.160000] TCP cubic registered [ 1.160000] NET: Registered protocol family 17 [ 1.160000] Bridge firewalling registered [ 1.170000] 8021q: 802.1Q VLAN Support v1.8 [ 1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.180000] Freeing unused kernel memory: 212k freed [ 3.460000] Registered led device: mk5:red:wlan1 [ 3.460000] Registered led device: mk5:blue:wlan0 [ 3.470000] Registered led device: mk5:amber:lan [ 6.780000] JFFS2 notice: (421) jffs2_build_xattr_subsystem: complete building xattr subsystem, 7 of xdatum (1 unchecked, 5 orphan) and 43 of xref (0 dead, 27 orphan) found. [ 7.750000] SCSI subsystem initialized [ 8.050000] usbcore: registered new interface driver usbfs [ 8.060000] usbcore: registered new interface driver hub [ 8.060000] usbcore: registered new device driver usb [ 8.410000] eth0: link up (100Mbps/Full duplex) [ 8.610000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.610000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 8.620000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 8.660000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 8.680000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 8.680000] hub 1-0:1.0: USB hub found [ 8.680000] hub 1-0:1.0: 1 port detected [ 8.790000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.920000] uhci_hcd: USB Universal Host Controller Interface driver [ 9.040000] Initializing USB Mass Storage driver... [ 9.040000] usbcore: registered new interface driver usb-storage [ 9.050000] USB Mass Storage support registered. [ 9.150000] usb 1-1: new high-speed USB device number 2 using ehci-platform [ 9.300000] hub 1-1:1.0: USB hub found [ 9.300000] hub 1-1:1.0: 4 ports detected [ 9.580000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform [ 9.800000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform [ 9.930000] scsi0 : usb-storage 1-1.2:1.0 [ 10.040000] usb 1-1.4: new high-speed USB device number 5 using ehci-platform [ 10.170000] scsi1 : usb-storage 1-1.4:1.0 [ 10.940000] scsi 0:0:0:0: CD-ROM NVTL Mass Storage 2.31 PQ: 0 ANSI: 2 [ 11.170000] scsi 1:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0 [ 11.790000] sd 1:0:0:0: [sda] 3686400 512-byte logical blocks: (1.88 GB/1.75 GiB) [ 11.790000] sd 1:0:0:0: [sda] Write Protect is off [ 11.800000] sd 1:0:0:0: [sda] Mode Sense: 03 00 00 00 [ 11.800000] sd 1:0:0:0: [sda] No Caching mode page present [ 11.800000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 11.810000] sd 1:0:0:0: [sda] No Caching mode page present [ 11.820000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 11.830000] sda: sda1 sda2 [ 11.830000] sd 1:0:0:0: [sda] No Caching mode page present [ 11.840000] sd 1:0:0:0: [sda] Assuming drive cache: write through [ 11.840000] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 29.460000] eth0: link down [ 30.420000] Loading modules backported from Linux version master-2014-01-23-0-g62c147d [ 30.430000] Backport generated by backports.git backports-20140124-0-g1256d3e [ 30.540000] cfg80211: Calling CRDA to update world regulatory domain [ 30.550000] cfg80211: World regulatory domain updated: [ 30.550000] cfg80211: DFS Master region: unset [ 30.560000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 30.570000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.570000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 30.580000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 30.590000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 30.600000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 30.610000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 32.100000] usbcore: registered new interface driver rt73usb [ 32.150000] ath: phy0: Enable LNA combining [ 32.150000] ath: EEPROM regdomain: 0x0 [ 32.150000] ath: EEPROM indicates default country code should be used [ 32.150000] ath: doing EEPROM country->regdmn map search [ 32.150000] ath: country maps to regdmn code: 0x3a [ 32.150000] ath: Country alpha2 being used: US [ 32.150000] ath: Regpair used: 0x3a [ 32.170000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 32.170000] Registered led device: ath9k-phy0 [ 32.170000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2 [ 32.180000] cfg80211: Calling CRDA for country: US [ 32.180000] cfg80211: Regulatory domain changed to country: US [ 32.180000] cfg80211: DFS Master region: FCC [ 32.190000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 32.200000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 32.200000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm) [ 32.210000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm) [ 32.220000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm) [ 32.230000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm) [ 32.240000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm) [ 32.240000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 32.530000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 32.530000] ieee80211 phy1: hwaddr 00:13:37:89:d0:3f, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2 [ 32.560000] rtl8187: Customer ID is 0x46 [ 32.560000] Registered led device: rtl8187-phy1::radio [ 32.560000] Registered led device: rtl8187-phy1::tx [ 32.560000] Registered led device: rtl8187-phy1::rx [ 32.560000] rtl8187: wireless switch is on [ 32.560000] usbcore: registered new interface driver rtl8187 [ 32.640000] Button Hotplug driver version 0.4.1 [ 32.860000] RPC: Registered named UNIX socket transport module. [ 32.860000] RPC: Registered udp transport module. [ 32.870000] RPC: Registered tcp transport module. [ 32.870000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 33.190000] PPP generic driver version 2.4.2 [ 33.220000] usbcore: registered new interface driver rt2800usb [ 33.350000] tun: Universal TUN/TAP device driver, 1.6 [ 33.360000] tun: © 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 33.710000] ip_tables: © 2000-2006 Netfilter Core Team [ 33.930000] NET: Registered protocol family 24 [ 34.080000] nf_conntrack version 0.5.0 (965 buckets, 3860 max) [ 34.780000] xt_time: kernel timezone is -0000 [ 35.300000] usbcore: registered new interface driver ath9k_htc [ 35.530000] usbcore: registered new interface driver usbserial [ 35.540000] USB Serial support registered for generic [ 35.540000] usbcore: registered new interface driver usbserial_generic [ 35.550000] usbserial: USB Serial Driver core [ 35.690000] usbcore: registered new interface driver asix [ 35.750000] usbcore: registered new interface driver cdc_ether [ 35.990000] Error: Driver 'gpio-keys-polled' is already registered, aborting... [ 36.100000] usbcore: registered new interface driver rndis_host [ 36.200000] scsi 0:0:0:0: Attached scsi generic sg0 type 5 [ 36.210000] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 36.230000] USB Serial support registered for GSM modem (1-port) [ 36.240000] usbcore: registered new interface driver option [ 36.240000] option: v0.7.2:USB Driver for GSM modems [ 36.270000] USB Serial support registered for pl2303 [ 36.270000] usbcore: registered new interface driver pl2303 [ 36.270000] pl2303: Prolific PL2303 USB to serial adaptor driver [ 42.450000] usb 1-1.2: USB disconnect, device number 4 [ 43.380000] usb 1-1.2: new high-speed USB device number 6 using ehci-platform [ 43.510000] usb 1-1.2: config 1 has an invalid interface number: 6 but max is 5 [ 43.510000] usb 1-1.2: config 1 has an invalid interface number: 7 but max is 5 [ 43.520000] usb 1-1.2: config 1 has an invalid interface number: 7 but max is 5 [ 43.530000] usb 1-1.2: config 1 has no interface number 4 [ 43.530000] usb 1-1.2: config 1 has no interface number 5 [ 43.560000] cdc_ether 1-1.2:1.6: eth1: register 'cdc_ether' at usb-ehci-platform-1.2, CDC Ethernet Device, 00:a0:c6:00:00:00 [ 44.630000] device eth0 entered promiscuous mode [ 44.650000] cdc_ether 1-1.2:1.6: eth1: CDC: unexpected notification 01! [ 44.780000] eth0: link up (100Mbps/Full duplex) [ 44.780000] br-lan: port 1(eth0) entered forwarding state [ 44.790000] br-lan: port 1(eth0) entered forwarding state [ 46.790000] br-lan: port 1(eth0) entered forwarding state [ 50.510000] device wlan0 entered promiscuous mode [ 50.780000] eth0: link down [ 50.860000] br-lan: port 2(wlan0) entered forwarding state [ 50.860000] br-lan: port 2(wlan0) entered forwarding state [ 51.510000] br-lan: port 1(eth0) entered disabled state [ 52.860000] br-lan: port 2(wlan0) entered forwarding state [ 54.780000] eth0: link up (100Mbps/Full duplex) [ 54.780000] br-lan: port 1(eth0) entered forwarding state [ 54.790000] br-lan: port 1(eth0) entered forwarding state [ 56.790000] br-lan: port 1(eth0) entered forwarding state [ 61.240000] wlan1: authenticate with 38:60:77:88:57:3e [ 62.520000] wlan1: send auth to 38:60:77:88:57:3e (try 1/3) [ 62.520000] wlan1: authenticated [ 62.590000] wlan1: associate with 38:60:77:88:57:3e (try 1/3) [ 62.770000] wlan1: RX AssocResp from 38:60:77:88:57:3e (capab=0x411 status=0 aid=8) [ 62.800000] wlan1: associated [ 75.950000] FPU emulator disabled, make sure your toolchainwas compiled with software floating point support (soft-float) root@Pineapple:~# And Smarty I'm not using battery power, it's right into the wall. But I don't think it's a power issue as the LED on the stick blinks for a couple seconds (The exact same every time) then goes out. Edited August 10, 2014 by ZeroSec Quote Link to comment Share on other sites More sharing options...
Smarty Posted August 11, 2014 Share Posted August 11, 2014 I understand.. Yet i had the exact same issue with an Huawei LTE dongle.. Didn't boot the dongle and didn't dial in. Used a USB port meter and all the leds turned off when it peaked at 0.76a. Power-usage when dialed in (on a laptop ) was just 0.4. Just once during the boot / initialization of the dongle it peaked at a level the MK5 couldn't provide. Resulted in a not working dongle. Not saying thats the case with you.. just something to keep in mind when troubleshooting your issue. Quote Link to comment Share on other sites More sharing options...
Smarty Posted August 11, 2014 Share Posted August 11, 2014 As for your output: [ 10.940000] scsi 0:0:0:0: CD-ROM NVTL Mass Storage 2.31 PQ: 0 ANSI: 2 I'd say your device is not modeswitching. Could your post the output of LSUSB ? If you have the Vendor and Product id from LSUSB google to what it should switch and try somehing like : usb_modeswitch -v 12d1 -p 1506 -c /etc/usb_modeswitch.d/12d1\:14fe Replace the vendor and product id to match your needs. Quote Link to comment Share on other sites More sharing options...
Darren Kitchen Posted August 11, 2014 Share Posted August 11, 2014 cdc_ether 1-1.2:1.6: eth1: register 'cdc_ether' at usb-ehci-platform-1.2, CDC Ethernet Device, 00:a0:c6:00:00:00 Your modem is up as eth1. You just need to static an IP and setup iptables forwarding. Search the forums for the other similar model Novatel modems. Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted August 12, 2014 Author Share Posted August 12, 2014 cdc_ether 1-1.2:1.6: eth1: register 'cdc_ether' at usb-ehci-platform-1.2, CDC Ethernet Device, 00:a0:c6:00:00:00 Your modem is up as eth1. You just need to static an IP and setup iptables forwarding. Search the forums for the other similar model Novatel modems. Thanks Darren! Its weird though because the LED on the modem is off. I'll try it out and see what happens. Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted August 12, 2014 Author Share Posted August 12, 2014 (edited) cdc_ether 1-1.2:1.6: eth1: register 'cdc_ether' at usb-ehci-platform-1.2, CDC Ethernet Device, 00:a0:c6:00:00:00 Your modem is up as eth1. You just need to static an IP and setup iptables forwarding. Search the forums for the other similar model Novatel modems. Used this setup https://forums.hak5.org/index.php?/topic/32785-usb-tether-to-novatel-5510l/?hl=novatel Where 100.71.42.* is the range (Got that by plugging it into my work computer and doing ipconfig) 10.1.1.* is my pineapples subnet Ran, ifconfig eth1 100.71.42.84 netmask 255.255.255.0 up route del default route add default gw 100.71.42.1 eth1 iptables -t nat -A POSTROUTING -s 10.1.1.0/24 -o eth1 -j MASQUERADE iptables -A FORWARD -s 10.1.1.0/24 -o eth1 -j ACCEPT iptables -A FORWARD -d 10.1.1.0/24 -m state --state ESTABLISHED,RELATED -i eth1 -j ACCEPT Tried it and got nothing, did a reboot tried it, and got nothing. It just hangs at " PING 8.8.8.8 (8.8.8.8): 56 data bytes " It never times out, which is strange... EDIT: At the end of dmesg I am now getting [ 79.540000] EXT4-fs (sda1): couldn't mount as ext3 due to feature incompatibilities [ 79.550000] EXT4-fs (sda1): couldn't mount as ext2 due to feature incompatibilities [ 79.580000] EXT4-fs (sda1): warning: mounting fs with errors, running e2fsck is recommended [ 79.590000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 80.510000] Adding 1002256k swap on /dev/sda2. Priority:-1 extents:1 across:1002256k [ 96.090000] cdc_ether 1-1.2:1.6: eth1: CDC: unexpected notification 01! EDIT2: (Sorry for editing so much, last time.) On my arch box dmesg also gives "469.721897 cdc_ether 1-1:1.6 enp0s16blah CDC: unexpected notification 01!" Edited August 12, 2014 by ZeroSec Quote Link to comment Share on other sites More sharing options...
Darren Kitchen Posted August 13, 2014 Share Posted August 13, 2014 Plug the modem into a regular computer and dial-up as usual. Check ip configuration and see what range it's on. For example when Mubix was here recently recording Metasploit Minute I helped him get a similar Verizon LTE dongle from Novatel online. It was running as 192.168.1.1 and had a little webserver going where you had to browse to and check a box for auto connect. It was a one time configuration. After that it's simply a matter of doing what you've stated above. Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted August 14, 2014 Author Share Posted August 14, 2014 (edited) Plug the modem into a regular computer and dial-up as usual. Check ip configuration and see what range it's on. For example when Mubix was here recently recording Metasploit Minute I helped him get a similar Verizon LTE dongle from Novatel online. It was running as 192.168.1.1 and had a little webserver going where you had to browse to and check a box for auto connect. It was a one time configuration. After that it's simply a matter of doing what you've stated above. It throws me into "100.71.42.*" I did a nmap scan and a netscan and was unable to find any web servers (also tried local IP). When I plug in the USB it opens up as storage, forces you to install the bloatware which when you click "connect" it comes up as a new device in the network connections list and works. There's nothing else I am able to find... Am I going to be better off to just buy a 4G LTE dongle thats supported? ​If so which one for a canadian carrier would you recommend? Edited August 15, 2014 by ZeroSec Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted August 20, 2014 Author Share Posted August 20, 2014 Nothing? :( Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted August 27, 2014 Author Share Posted August 27, 2014 Bump? Quote Link to comment Share on other sites More sharing options...
ZeroSec Posted September 30, 2014 Author Share Posted September 30, 2014 Final bumb before I give up... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.