Jump to content

SD card corruption?

markcoker

By markcoker
in WiFi Pineapple Mark V

 Share

Recommended Posts

markcoker Newbie

markcoker

Posted
Posted (edited)

UPDATE: /sd contains nothing, it isnt mounted!

Any suggestions?

Thanks guys!

Current firmware 1.04

I had a update in pineapple bar and configuration was missing so i restarted a few times (there was a new update that fixed this issue :), but upon restart /sd contains nothing. I had all my infusions/scripts/captures etc on there.

Its my understanding that the pineapple needs the SD to operate? its strange its not mounted to /sd but i can still for the most part use the pineapple.

Maybe a mounting issue? what should i do?

edit: Restored firmware though web interface.... still no SD!

Corruption? (fdisk -l)

Disk /dev/mtdblock0: 0 MB, 131072 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock0 doesn't contain a valid partition table
Disk /dev/mtdblock1: 0 MB, 927232 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock1 doesn't contain a valid partition table
Disk /dev/mtdblock2: 15 MB, 15652864 bytes
255 heads, 63 sectors/track, 1 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock2 doesn't contain a valid partition table
Disk /dev/mtdblock3: 4 MB, 4259840 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock3 doesn't contain a valid partition table
Disk /dev/mtdblock4: 0 MB, 65536 bytes
255 heads, 63 sectors/track, 0 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock4 doesn't contain a valid partition table
Disk /dev/mtdblock5: 16 MB, 16580608 bytes
255 heads, 63 sectors/track, 2 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/mtdblock5 doesn't contain a valid partition table
Disk /dev/sda: 1887 MB, 1887436800 bytes
59 heads, 62 sectors/track, 1007 cylinders
Units = cylinders of 3658 * 512 = 1872896 bytes
Disk /dev/sda doesn't contain a valid partition table

Fstab Configuration:

root@Pineapple:/dev/sdcard# ls
sd
config global automount
option from_fstab 1
option anon_mount 1


config global autoswap
option from_fstab 1
option anon_swap 0


config mount
option target /sd
option device /dev/sdcard/sd1
option fstype auto
option options rw,sync
option enabled 1
option enabled_fsck 0


config swap
option device /dev/sdcard/sd2
option enabled 1

So i got another SD card formatted it to fat32 and loaded both update.bin (md5 hash checked) and md5.

it does its magic and boots, i ssh to the device and /sd isnt mounted and issues with webclient (http://172.16.42.1:1471/ doesnt work http://172.16.42.1/ changes to http://172.16.42.1/redirect.php then goes back to whatever page i previously was on.

Im considering loading stager.bin, i dont think it will work but im out of ideas.

UPDATE:
so ive reloaded the stager.bin > booted with sd card, create new password etc. The new SD card is showing up now but.... i put the old SD card in hoping it would be fixed /sd still doesnt mount. Im assuming these files are lost and SD is prob no good?

SYSLOG:

Syslog Output:
00:01:51 Pineapple auth.info sshd[1674]: Accepted password for root from 172.16.42.42 port 2359 ssh2
00:01:47 Pineapple auth.info sshd[1674]: WARNING: /etc/ssh/moduli does not exist, using fixed modulus
00:01:03 Pineapple user.info sysinit: setting up led wlan1
00:01:03 Pineapple user.info sysinit: setting up led wlan0
00:01:03 Pineapple user.info sysinit: setting up led ethernet
00:01:03 Pineapple daemon.info dnsmasq[1640]: using nameserver 8.8.8.8#53
00:01:03 Pineapple daemon.info dnsmasq[1640]: using local addresses only for domain lan
00:01:03 Pineapple daemon.info dnsmasq[1640]: using local addresses only for domain lan
00:01:03 Pineapple daemon.info dnsmasq[1640]: started, version 2.66 cachesize 150
00:01:03 Pineapple daemon.info dnsmasq[1640]: reading /tmp/resolv.conf.auto
00:01:03 Pineapple daemon.info dnsmasq[1640]: read /etc/hosts - 1 addresses
00:01:03 Pineapple daemon.info dnsmasq[1640]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
00:01:03 Pineapple daemon.info dnsmasq-dhcp[1640]: read /etc/ethers - 0 addresses
00:01:03 Pineapple daemon.info dnsmasq-dhcp[1640]: DHCP, IP range 172.16.42.100 -- 172.16.42.249, lease time 12h
00:00:59 Pineapple user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
00:00:59 Pineapple user.notice dnsmasq: Allowing 127.0.0.0/8 responses
00:00:56 Pineapple auth.info sshd[1573]: Server listening on 0.0.0.0 port 22.
00:00:55 Pineapple user.info sysinit: Failed to start hostapd for phy1
00:00:55 Pineapple cron.info crond[1567]: crond: crond (busybox 1.19.4) started, log level 5
00:00:50 Pineapple kern.info kernel: [ 50.930000] br-lan: port 2(wlan0) entered forwarding state
00:00:48 Pineapple kern.info kernel: [ 48.930000] br-lan: port 2(wlan0) entered forwarding state
00:00:48 Pineapple kern.info kernel: [ 48.920000] br-lan: port 2(wlan0) entered forwarding state
00:00:48 Pineapple kern.info kernel: [ 48.870000] device wlan0 entered promiscuous mode
00:00:46 Pineapple kern.info kernel: [ 46.040000] br-lan: port 1(eth0) entered forwarding state
00:00:44 Pineapple user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
00:00:44 Pineapple kern.info kernel: [ 44.040000] br-lan: port 1(eth0) entered forwarding state
00:00:44 Pineapple kern.info kernel: [ 44.030000] eth0: link up (100Mbps/Full duplex)
00:00:44 Pineapple kern.info kernel: [ 44.030000] br-lan: port 1(eth0) entered forwarding state
00:00:43 Pineapple user.notice usb-modeswitch: 1-1.4:1.0: Manufacturer=Generic Product=Mass_Storage_Device Serial=058F0O1111B1
00:00:43 Pineapple kern.info kernel: [ 43.700000] device eth0 entered promiscuous mode
00:00:43 Pineapple kern.info kernel: [ 43.130000] usbserial: USB Serial Driver core
00:00:43 Pineapple kern.info kernel: [ 43.130000] usbcore: registered new interface driver usbserial_generic
00:00:43 Pineapple kern.info kernel: [ 43.120000] usbcore: registered new interface driver usbserial
00:00:43 Pineapple kern.info kernel: [ 43.120000] USB Serial support registered for generic
00:00:43 Pineapple kern.info kernel: [ 43.080000] usbcore: deregistering interface driver usbserial
00:00:43 Pineapple kern.info kernel: [ 43.070000] usbcore: deregistering interface driver usbserial_generic
00:00:43 Pineapple kern.info kernel: [ 43.070000] USB Serial deregistering driver generic
00:00:43 Pineapple daemon.notice netifd: Interface 'loopback' is now up
00:00:43 Pineapple daemon.notice netifd: Interface 'lan' is now up
00:00:42 Pineapple user.notice usb-modeswitch: 1-1.1:1.0: Manufacturer=Manufacturer_Realtek_RTL8187_ Product=RTL8187_Wireless Serial=00133789D3FD
00:00:42 Pineapple kern.info kernel: [ 42.720000] usbserial: USB Serial Driver core
00:00:42 Pineapple kern.info kernel: [ 42.720000] usbcore: registered new interface driver usbserial_generic
00:00:42 Pineapple kern.info kernel: [ 42.710000] usbcore: registered new interface driver usbserial
00:00:42 Pineapple kern.info kernel: [ 42.710000] USB Serial support registered for generic
00:00:42 Pineapple kern.info kernel: [ 42.660000] usbcore: deregistering interface driver usbserial
00:00:42 Pineapple kern.info kernel: [ 42.660000] USB Serial deregistering driver generic
00:00:42 Pineapple kern.info kernel: [ 42.650000] usbcore: deregistering interface driver usbserial_generic
00:00:41 Pineapple user.notice usb-modeswitch: 1-1:1.0: Manufacturer=? Product=USB2.0Hub Serial=?
00:00:41 Pineapple user.notice usb-modeswitch: 1-0:1.0: Manufacturer=Linux_3.3.8_ehci_hcd Product=Generic_Platform_EHCI_Controller Serial=ehci-platform
00:00:41 Pineapple kern.info kernel: [ 41.950000] usbserial: USB Serial Driver core
00:00:41 Pineapple kern.info kernel: [ 41.950000] usbcore: registered new interface driver usbserial_generic
00:00:41 Pineapple kern.info kernel: [ 41.940000] usbcore: registered new interface driver usbserial
00:00:41 Pineapple kern.info kernel: [ 41.940000] USB Serial support registered for generic
00:00:41 Pineapple kern.info kernel: [ 41.790000] usbcore: deregistering interface driver usbserial
00:00:41 Pineapple kern.info kernel: [ 41.790000] USB Serial deregistering driver generic
00:00:41 Pineapple kern.info kernel: [ 41.780000] usbcore: deregistering interface driver usbserial_generic
00:00:41 Pineapple kern.info kernel: [ 41.120000] usbserial: USB Serial Driver core
00:00:41 Pineapple kern.info kernel: [ 41.120000] usbcore: registered new interface driver usbserial_generic
00:00:41 Pineapple kern.info kernel: [ 41.110000] usbcore: registered new interface driver usbserial
00:00:41 Pineapple kern.info kernel: [ 41.110000] USB Serial support registered for generic
00:00:41 Pineapple kern.info kernel: [ 41.060000] usbcore: deregistering interface driver usbserial
00:00:41 Pineapple kern.info kernel: [ 41.060000] USB Serial deregistering driver generic
00:00:41 Pineapple kern.info kernel: [ 41.050000] usbcore: deregistering interface driver usbserial_generic
00:00:38 Pineapple kern.notice kernel: [ 36.320000] sd 0:0:0:0: Attached scsi generic sg0 type 0
00:00:38 Pineapple kern.info kernel: [ 36.200000] usbcore: registered new interface driver rndis_host
00:00:38 Pineapple kern.info kernel: [ 35.970000] usbcore: registered new interface driver cdc_ether
00:00:38 Pineapple kern.info kernel: [ 35.840000] usbcore: registered new interface driver asix
00:00:38 Pineapple kern.info kernel: [ 35.700000] usbserial: USB Serial Driver core
00:00:38 Pineapple kern.info kernel: [ 35.690000] usbcore: registered new interface driver usbserial_generic
00:00:38 Pineapple kern.info kernel: [ 35.690000] USB Serial support registered for generic
00:00:38 Pineapple kern.info kernel: [ 35.680000] usbcore: registered new interface driver usbserial
00:00:38 Pineapple kern.info kernel: [ 35.450000] usbcore: registered new interface driver ath9k_htc
00:00:38 Pineapple kern.info kernel: [ 34.980000] xt_time: kernel timezone is -0000
00:00:38 Pineapple kern.info kernel: [ 34.270000] nf_conntrack version 0.5.0 (965 buckets, 3860 max)
00:00:38 Pineapple kern.info kernel: [ 34.130000] NET: Registered protocol family 24
00:00:38 Pineapple kern.info kernel: [ 33.890000] ip_tables: © 2000-2006 Netfilter Core Team
00:00:38 Pineapple kern.info kernel: [ 33.630000] tun: Universal TUN/TAP device driver, 1.6
00:00:38 Pineapple kern.info kernel: [ 33.630000] tun: © 1999-2004 Max Krasnyansky
00:00:38 Pineapple kern.info kernel: [ 33.590000] PPP generic driver version 2.4.2
00:00:38 Pineapple kern.info kernel: [ 33.340000] RPC: Registered tcp NFSv4.1 backchannel transport module.
00:00:38 Pineapple kern.info kernel: [ 33.330000] RPC: Registered tcp transport module.
00:00:38 Pineapple kern.err kernel: [ 36.090000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
00:00:37 Pineapple kern.notice kernel: [ 11.910000] sd 0:0:0:0: [sda] Attached SCSI removable disk
00:00:37 Pineapple kern.notice kernel: [ 11.860000] sd 0:0:0:0: [sda] Write Protect is off
00:00:37 Pineapple kern.notice kernel: [ 11.860000] sd 0:0:0:0: [sda] 3686400 512-byte logical blocks: (1.88 GB/1.75 GiB)
00:00:37 Pineapple kern.notice kernel: [ 11.230000] scsi 0:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
00:00:37 Pineapple kern.info kernel: [ 33.330000] RPC: Registered udp transport module.
00:00:37 Pineapple kern.info kernel: [ 33.320000] RPC: Registered named UNIX socket transport module.
00:00:37 Pineapple kern.info kernel: [ 33.110000] Button Hotplug driver version 0.4.1
00:00:37 Pineapple kern.info kernel: [ 33.080000] usbcore: registered new interface driver rtl8187
00:00:37 Pineapple kern.info kernel: [ 33.080000] rtl8187: wireless switch is on
00:00:37 Pineapple kern.info kernel: [ 33.080000] rtl8187: Customer ID is 0x46
00:00:37 Pineapple kern.info kernel: [ 33.050000] ieee80211 phy1: hwaddr 00:13:37:89:d3:fd, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2
00:00:37 Pineapple kern.info kernel: [ 32.640000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
00:00:37 Pineapple kern.info kernel: [ 32.630000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 32.620000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 32.610000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 32.610000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
00:00:37 Pineapple kern.info kernel: [ 32.600000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
00:00:37 Pineapple kern.info kernel: [ 32.590000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
00:00:37 Pineapple kern.info kernel: [ 32.580000] cfg80211: Regulatory domain changed to country: US
00:00:37 Pineapple kern.info kernel: [ 32.580000] cfg80211: Calling CRDA for country: US
00:00:37 Pineapple kern.info kernel: [ 32.570000] usbcore: registered new interface driver rt2800usb
00:00:37 Pineapple kern.info kernel: [ 32.550000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
00:00:37 Pineapple kern.info kernel: [ 32.490000] usbcore: registered new interface driver rt73usb
00:00:37 Pineapple kern.info kernel: [ 30.950000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 30.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 30.940000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 30.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 30.920000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
00:00:37 Pineapple kern.info kernel: [ 30.920000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
00:00:37 Pineapple kern.info kernel: [ 30.910000] cfg80211: World regulatory domain updated:
00:00:37 Pineapple kern.info kernel: [ 30.910000] cfg80211: Calling CRDA to update world regulatory domain
00:00:37 Pineapple kern.info kernel: [ 30.760000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
00:00:37 Pineapple kern.info kernel: [ 30.760000] Backport generated by backports.git backports-20130617-4-ge3220f5
00:00:37 Pineapple kern.info kernel: [ 29.740000] eth0: link down
00:00:37 Pineapple kern.info kernel: [ 11.900000] sda: unknown partition table
00:00:37 Pineapple kern.info kernel: [ 10.230000] scsi0 : usb-storage 1-1.4:1.0
00:00:37 Pineapple kern.info kernel: [ 10.100000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform
00:00:37 Pineapple kern.info kernel: [ 9.860000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
00:00:37 Pineapple kern.info kernel: [ 9.580000] hub 1-1:1.0: USB hub found
00:00:37 Pineapple kern.info kernel: [ 9.580000] hub 1-1:1.0: 4 ports detected
00:00:37 Pineapple kern.info kernel: [ 9.430000] usb 1-1: new high-speed USB device number 2 using ehci-platform
00:00:37 Pineapple kern.info kernel: [ 9.330000] USB Mass Storage support registered.
00:00:37 Pineapple kern.info kernel: [ 9.320000] usbcore: registered new interface driver usb-storage
00:00:37 Pineapple kern.info kernel: [ 9.320000] Initializing USB Mass Storage driver...
00:00:37 Pineapple kern.info kernel: [ 9.200000] uhci_hcd: USB Universal Host Controller Interface driver
00:00:37 Pineapple kern.info kernel: [ 9.080000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
00:00:37 Pineapple kern.info kernel: [ 8.950000] hub 1-0:1.0: USB hub found
00:00:37 Pineapple kern.info kernel: [ 8.950000] hub 1-0:1.0: 1 port detected
00:00:37 Pineapple kern.info kernel: [ 8.950000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
00:00:37 Pineapple kern.info kernel: [ 8.930000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
00:00:37 Pineapple kern.err kernel: [ 11.910000] sd 0:0:0:0: [sda] Assuming drive cache: write through
00:00:37 Pineapple kern.err kernel: [ 11.900000] sd 0:0:0:0: [sda] No Caching mode page present
00:00:37 Pineapple kern.err kernel: [ 11.890000] sd 0:0:0:0: [sda] Assuming drive cache: write through
00:00:37 Pineapple kern.err kernel: [ 11.880000] sd 0:0:0:0: [sda] No Caching mode page present
00:00:37 Pineapple kern.err kernel: [ 11.870000] sd 0:0:0:0: [sda] No Caching mode page present
00:00:37 Pineapple kern.err kernel: [ 11.870000] sd 0:0:0:0: [sda] Assuming drive cache: write through
00:00:37 Pineapple kern.debug kernel: [ 33.080000] Registered led device: rtl8187-phy1::tx
00:00:37 Pineapple kern.debug kernel: [ 33.080000] Registered led device: rtl8187-phy1::rx
00:00:37 Pineapple kern.debug kernel: [ 33.080000] Registered led device: rtl8187-phy1::radio
00:00:37 Pineapple kern.debug kernel: [ 33.050000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
00:00:37 Pineapple kern.debug kernel: [ 32.550000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
00:00:37 Pineapple kern.debug kernel: [ 32.550000] Registered led device: ath9k-phy0
00:00:37 Pineapple kern.debug kernel: [ 32.540000] ath: doing EEPROM country->regdmn map search
00:00:37 Pineapple kern.debug kernel: [ 32.540000] ath: country maps to regdmn code: 0x3a
00:00:37 Pineapple kern.debug kernel: [ 32.540000] ath: Regpair used: 0x3a
00:00:37 Pineapple kern.debug kernel: [ 32.540000] ath: EEPROM regdomain: 0x0
00:00:37 Pineapple kern.debug kernel: [ 32.540000] ath: EEPROM indicates default country code should be used
00:00:37 Pineapple kern.debug kernel: [ 32.540000] ath: Country alpha2 being used: US
00:00:37 Pineapple kern.debug kernel: [ 11.870000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00

DMESG:

Dmesg Output:
[ 0.000000] Linux version 3.3.8 (sebkinne@buildtop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #31 Fri Nov 22 15:47:49 CET 2013
[ 0.000000] MyLoader: sysp=97d936c9, boardp=61b798de, parts=6238a85e
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802d8470, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16256 pages, LIFO batch:3
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=MK5 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61596k/65536k available (2124k kernel code, 3940k reserved, 405k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is MK5 V1.0
[ 0.350000] bio: create slab at 0
[ 0.360000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.380000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.380000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.390000] TCP reno registered
[ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] NET: Registered protocol family 1
[ 0.410000] PCI: CLS 0 bytes, default 32
[ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.
[ 0.440000] msgmni has been set to 120
[ 0.440000] io scheduler noop registered
[ 0.450000] io scheduler deadline registered (default)
[ 0.450000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.460000] console [ttyATH0] enabled, bootconsole disabled
[ 0.480000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.480000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.490000] 5 tp-link partitions found on MTD device spi0.0
[ 0.490000] Creating 5 MTD partitions on "spi0.0":
[ 0.500000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.510000] 0x000000020000-0x000000102748 : "kernel"
[ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.520000] 0x000000102748-0x000000ff0000 : "rootfs"
[ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] mtd: partition "rootfs" set to be root filesystem
[ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=BE0000, len=410000
[ 0.550000] 0x000000be0000-0x000000ff0000 : "rootfs_data"
[ 0.560000] 0x000000ff0000-0x000001000000 : "art"
[ 0.570000] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.590000] ag71xx_mdio: probed
[ 0.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.160000] TCP cubic registered
[ 1.160000] NET: Registered protocol family 17
[ 1.160000] Bridge firewalling registered
[ 1.170000] 8021q: 802.1Q VLAN Support v1.8
[ 1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.190000] Freeing unused kernel memory: 208k freed
[ 3.680000] Registered led device: mk5:red:wlan1
[ 3.680000] Registered led device: mk5:blue:wlan0
[ 3.680000] Registered led device: mk5:amber:lan
[ 6.160000] eth0: link up (100Mbps/Full duplex)
[ 7.000000] JFFS2 notice: (422) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 27 of xref (0 dead, 9 orphan) found.
[ 8.020000] SCSI subsystem initialized
[ 8.310000] usbcore: registered new interface driver usbfs
[ 8.310000] usbcore: registered new interface driver hub
[ 8.320000] usbcore: registered new device driver usb
[ 8.880000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.890000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 8.890000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 8.930000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 8.950000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 8.950000] hub 1-0:1.0: USB hub found
[ 8.950000] hub 1-0:1.0: 1 port detected
[ 9.080000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.200000] uhci_hcd: USB Universal Host Controller Interface driver
[ 9.320000] Initializing USB Mass Storage driver...
[ 9.320000] usbcore: registered new interface driver usb-storage
[ 9.330000] USB Mass Storage support registered.
[ 9.430000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 9.580000] hub 1-1:1.0: USB hub found
[ 9.580000] hub 1-1:1.0: 4 ports detected
[ 9.860000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[ 10.100000] usb 1-1.4: new high-speed USB device number 4 using ehci-platform
[ 10.230000] scsi0 : usb-storage 1-1.4:1.0
[ 11.230000] scsi 0:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
[ 11.860000] sd 0:0:0:0: [sda] 3686400 512-byte logical blocks: (1.88 GB/1.75 GiB)
[ 11.860000] sd 0:0:0:0: [sda] Write Protect is off
[ 11.870000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 11.870000] sd 0:0:0:0: [sda] No Caching mode page present
[ 11.870000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 11.880000] sd 0:0:0:0: [sda] No Caching mode page present
[ 11.890000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 11.900000] sda: unknown partition table
[ 11.900000] sd 0:0:0:0: [sda] No Caching mode page present
[ 11.910000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 11.910000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 29.740000] eth0: link down
[ 30.760000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 30.760000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 30.910000] cfg80211: Calling CRDA to update world regulatory domain
[ 30.910000] cfg80211: World regulatory domain updated:
[ 30.920000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 30.920000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 30.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 30.940000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 30.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 30.950000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.490000] usbcore: registered new interface driver rt73usb
[ 32.540000] ath: EEPROM regdomain: 0x0
[ 32.540000] ath: EEPROM indicates default country code should be used
[ 32.540000] ath: doing EEPROM country->regdmn map search
[ 32.540000] ath: country maps to regdmn code: 0x3a
[ 32.540000] ath: Country alpha2 being used: US
[ 32.540000] ath: Regpair used: 0x3a
[ 32.550000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 32.550000] Registered led device: ath9k-phy0
[ 32.550000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 32.570000] usbcore: registered new interface driver rt2800usb
[ 32.580000] cfg80211: Calling CRDA for country: US
[ 32.580000] cfg80211: Regulatory domain changed to country: US
[ 32.590000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.600000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 32.610000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 32.610000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.620000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.630000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.640000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 33.050000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 33.050000] ieee80211 phy1: hwaddr 00:13:37:89:d3:fd, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2
[ 33.080000] rtl8187: Customer ID is 0x46
[ 33.080000] Registered led device: rtl8187-phy1::radio
[ 33.080000] Registered led device: rtl8187-phy1::tx
[ 33.080000] Registered led device: rtl8187-phy1::rx
[ 33.080000] rtl8187: wireless switch is on
[ 33.080000] usbcore: registered new interface driver rtl8187
[ 33.110000] Button Hotplug driver version 0.4.1
[ 33.320000] RPC: Registered named UNIX socket transport module.
[ 33.330000] RPC: Registered udp transport module.
[ 33.330000] RPC: Registered tcp transport module.
[ 33.340000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 33.590000] PPP generic driver version 2.4.2
[ 33.630000] tun: Universal TUN/TAP device driver, 1.6
[ 33.630000] tun: © 1999-2004 Max Krasnyansky
[ 33.890000] ip_tables: © 2000-2006 Netfilter Core Team
[ 34.130000] NET: Registered protocol family 24
[ 34.270000] nf_conntrack version 0.5.0 (965 buckets, 3860 max)
[ 34.980000] xt_time: kernel timezone is -0000
[ 35.450000] usbcore: registered new interface driver ath9k_htc
[ 35.680000] usbcore: registered new interface driver usbserial
[ 35.690000] USB Serial support registered for generic
[ 35.690000] usbcore: registered new interface driver usbserial_generic
[ 35.700000] usbserial: USB Serial Driver core
[ 35.840000] usbcore: registered new interface driver asix
[ 35.970000] usbcore: registered new interface driver cdc_ether
[ 36.090000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 36.200000] usbcore: registered new interface driver rndis_host
[ 36.320000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 41.050000] usbcore: deregistering interface driver usbserial_generic
[ 41.060000] USB Serial deregistering driver generic
[ 41.060000] usbcore: deregistering interface driver usbserial
[ 41.110000] usbcore: registered new interface driver usbserial
[ 41.110000] USB Serial support registered for generic
[ 41.120000] usbcore: registered new interface driver usbserial_generic
[ 41.120000] usbserial: USB Serial Driver core
[ 41.780000] usbcore: deregistering interface driver usbserial_generic
[ 41.790000] USB Serial deregistering driver generic
[ 41.790000] usbcore: deregistering interface driver usbserial
[ 41.940000] usbcore: registered new interface driver usbserial
[ 41.940000] USB Serial support registered for generic
[ 41.950000] usbcore: registered new interface driver usbserial_generic
[ 41.950000] usbserial: USB Serial Driver core
[ 42.650000] usbcore: deregistering interface driver usbserial_generic
[ 42.660000] USB Serial deregistering driver generic
[ 42.660000] usbcore: deregistering interface driver usbserial
[ 42.710000] usbcore: registered new interface driver usbserial
[ 42.710000] USB Serial support registered for generic
[ 42.720000] usbcore: registered new interface driver usbserial_generic
[ 42.720000] usbserial: USB Serial Driver core
[ 43.070000] usbcore: deregistering interface driver usbserial_generic
[ 43.070000] USB Serial deregistering driver generic
[ 43.080000] usbcore: deregistering interface driver usbserial
[ 43.120000] usbcore: registered new interface driver usbserial
[ 43.120000] USB Serial support registered for generic
[ 43.130000] usbcore: registered new interface driver usbserial_generic
[ 43.130000] usbserial: USB Serial Driver core
[ 43.700000] device eth0 entered promiscuous mode
[ 44.030000] eth0: link up (100Mbps/Full duplex)
[ 44.030000] br-lan: port 1(eth0) entered forwarding state
[ 44.040000] br-lan: port 1(eth0) entered forwarding state
[ 46.040000] br-lan: port 1(eth0) entered forwarding state
[ 48.870000] device wlan0 entered promiscuous mode
[ 48.920000] br-lan: port 2(wlan0) entered forwarding state
[ 48.930000] br-lan: port 2(wlan0) entered forwarding state
[ 50.930000] br-lan: port 2(wlan0) entered forwarding state

Edited by markcoker
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...