Jump to content

Proxmox Problems? :(


Recommended Posts

So I'm trying to setup my quadcore 955 black edition running on a M4A79T Deluxe SE board with the built in ethernet, however the latest version of proxmox won't allow me to connect to it after installing to a terabyte hard disk.

I've run IFCONFIG and this is what the screen displays:

Link encap: Ethernet HWaddr 00:24:8c:6e:bd:c0
inet6 addr fe80:224:8cff:fe6e:bdc0/64 Scope: Link
UP BROADCAST RUNNING MULTICAST MTU: 1500 Metric:1
RX Packets: 0 errors: 0 dropped: 0 overruns: 0 frame:0
TX packets: 68 errors: 0 dropped: 0 overruns: 0 carrier:0
collisions: 0 txqueueclcn: 1000
RX bytes: 0 (0.0 B) TX bytes: 3328 (3.2KiB)

Link encap: Local Loopback
inet addr:127.0.0.1 Mask: 255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets: 40 errors:0 dropped: 0 overruns:0 frame:0
TX packets: 40 errors: 0 dropped:0 overruns:0 carrier:0
collisions: 0 txquelen:0
RX Bytes: 3864 (3.7 KiB) TX bytes: 3864 (3.7 KiB)

Link encap: UNSPEC HWAddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet6 addr: fe80::1/28 Scope:Link
UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:3 overruns:0 carrier:0
collisions:0 txquelen:0
RX bytes:0 (0.0B) TX bytes:0 (0.0B)

Link encap: Ethernet HWaddr:00:24:8c:6e:bd:c0
inetaddr:192.168.1.5 Bcast:192.168.1.255 Mask: 255.255.255.0
inet6 addr: fe80::224:8cff:fe6e:bdc0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:60 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txquelen:0
RX bytes(0.0B) TX Bytes:2776(2.7KiB)

My primary router is set up in this configuration:

Default Gateway: 96.253.86.1 DNS Server: 71.252.0.12
68.238.112.12

Although I have set the gateway and DNS server during installation to 192.168.1.1 for both, and the IP address as 192.168.1.5

Do I need to reinstall and use the default gateway as shown in my router? by the way, this is a cruddy MI424WR router. YUCK!

This is also as stated, hooked up directly to ethernet and appears to have a link.

I try to connect to 192.168.1.5 and it actually trys to connect for about a minute and then displays the typical "The connection has timed out" page.

The server at 192.168.1.5(:8006)is taking too long to respond.

If it matters, I am also logged in as root while trying to connect.

Edited by 40Tons_Of_Bananas
Link to post
Share on other sites

1. I assume you are trying to connect to it from a machine on the same LAN.

2. Can you ping it?

3. Port 8006?

(Note I'm running an older version of Proxmox, so I don't know if they've changed something, but this sounds like a basic network issue)

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...