Jump to content

My Pineapple Can't Connect, and Doesn't Show Up As A Network.


Draconem
 Share

Recommended Posts

Hello! I just did a factory reset of my pineapple and i enabled wlan1. I went to the "network" and then went to the "Client mode" tab. I chose my internet and type in my password. Even when i have waited like 2 minutes or close the tab and then go back to it, it still says im "not connected" at the bottom. And it says on w1an1: N/A which means im not connected. But the weird thing is, when i click on "Internet IP" it shows me an IP and when I go to the Pineapple bar i can load the modules. And im connecting to my pineapple via my macbook --> (which is not connected to the internet! And does not have sharing enabled!) <-- so the pineapple can NOT get its internet over my laptop.. So it is connected to the internet in some way but on w1an1 it says N/A and if i go back to the "client mode" tab it says "not connected" at the bottom and it asks me to choose a ssid, IF i do this again the same thing as above will happen so that doesn't help.. And also when i look in the Wifi menu I cant see my pineapple, on any device (phone, laptop). What is happening!?! This is my iwconfig:

lo no wireless extensions.

wlan1 IEEE 802.11bg ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=27 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
wlan0 IEEE 802.11bgn ESSID:"4a350c"
Mode:Managed Frequency:2.462 GHz Access Point: 70:71:BC:34:6F:FE
Bit Rate=24 Mb/s Tx-Power=18 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=42/70 Signal level=-68 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:9 Missed beacon:0
eth0 no wireless extensions.
br-lan no wireless extensions.
Yes, "4a350c" is my network, im not sure why "encryption key" is off, maybe it should, but my wifi has a password (and yes i did enter it in the pineapple).
And here is my ifconfig:

br-lan Link encap:Ethernet HWaddr 00:13:37:A5:08:26

inet addr:172.16.42.1 Bcast:172.16.42.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8937 errors:0 dropped:116 overruns:0 frame:0
TX packets:7281 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1183443 (1.1 MiB) TX bytes:1124217 (1.0 MiB)
eth0 Link encap:Ethernet HWaddr 00:13:37:A5:08:26
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:8969 errors:0 dropped:15 overruns:0 frame:0
TX packets:7281 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1318613 (1.2 MiB) TX bytes:1124217 (1.0 MiB)
Interrupt:4
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:609 errors:0 dropped:0 overruns:0 frame:0
TX packets:609 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:44059 (43.0 KiB) TX bytes:44059 (43.0 KiB)
wlan0 Link encap:Ethernet HWaddr 00:13:37:A5:08:26
inet addr:192.168.0.24 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:992 errors:0 dropped:191 overruns:0 frame:0
TX packets:510 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:259319 (253.2 KiB) TX bytes:70928 (69.2 KiB)
wlan1 Link encap:Ethernet HWaddr 00:13:37:81:43:7F
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
My wlan0 says its connected to "ethernet" but my macbook doesnt have internet... and that it has a internet address 0_o my head hurts..

PLEASE help me! Thanks you guys!

Link to comment
Share on other sites

Since the recent update, my Mark V won't connect as a client either.
Worked fine, updated everything, rebooted, and now it won't connect.

It also appears Karma clients can't connect now either (they can see the networks created, just not connect to them). :(

EDIT: I had to use the Wifi Manager infusion to get it to connect as a client.

Edited by Tommo
Link to comment
Share on other sites

  • 3 weeks later...

My pineapple now works in client mode (and with wlan1) ! In IRC you told me a command then i rebooted and it fixed the problem DNS spoof and Karma is still not working tough :/

Hi there. Please share the command to fix client mode problem. I'm having the same issue. Thanks in adv.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...