Draconem Posted October 27, 2013 Share Posted October 27, 2013 Hello! I just did a factory reset of my pineapple and i enabled wlan1. I went to the "network" and then went to the "Client mode" tab. I chose my internet and type in my password. Even when i have waited like 2 minutes or close the tab and then go back to it, it still says im "not connected" at the bottom. And it says on w1an1: N/A which means im not connected. But the weird thing is, when i click on "Internet IP" it shows me an IP and when I go to the Pineapple bar i can load the modules. And im connecting to my pineapple via my macbook --> (which is not connected to the internet! And does not have sharing enabled!) <-- so the pineapple can NOT get its internet over my laptop.. So it is connected to the internet in some way but on w1an1 it says N/A and if i go back to the "client mode" tab it says "not connected" at the bottom and it asks me to choose a ssid, IF i do this again the same thing as above will happen so that doesn't help.. And also when i look in the Wifi menu I cant see my pineapple, on any device (phone, laptop). What is happening!?! This is my iwconfig: lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=27 dBm RTS thr:off Fragment thr:off Encryption key:off Power Management:off wlan0 IEEE 802.11bgn ESSID:"4a350c" Mode:Managed Frequency:2.462 GHz Access Point: 70:71:BC:34:6F:FE Bit Rate=24 Mb/s Tx-Power=18 dBm RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=42/70 Signal level=-68 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:9 Missed beacon:0 eth0 no wireless extensions. br-lan no wireless extensions. Yes, "4a350c" is my network, im not sure why "encryption key" is off, maybe it should, but my wifi has a password (and yes i did enter it in the pineapple). And here is my ifconfig: br-lan Link encap:Ethernet HWaddr 00:13:37:A5:08:26 inet addr:172.16.42.1 Bcast:172.16.42.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8937 errors:0 dropped:116 overruns:0 frame:0 TX packets:7281 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1183443 (1.1 MiB) TX bytes:1124217 (1.0 MiB) eth0 Link encap:Ethernet HWaddr 00:13:37:A5:08:26 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8969 errors:0 dropped:15 overruns:0 frame:0 TX packets:7281 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1318613 (1.2 MiB) TX bytes:1124217 (1.0 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:609 errors:0 dropped:0 overruns:0 frame:0 TX packets:609 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:44059 (43.0 KiB) TX bytes:44059 (43.0 KiB) wlan0 Link encap:Ethernet HWaddr 00:13:37:A5:08:26 inet addr:192.168.0.24 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:992 errors:0 dropped:191 overruns:0 frame:0 TX packets:510 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:259319 (253.2 KiB) TX bytes:70928 (69.2 KiB) wlan1 Link encap:Ethernet HWaddr 00:13:37:81:43:7F UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) My wlan0 says its connected to "ethernet" but my macbook doesnt have internet... and that it has a internet address 0_o my head hurts.. PLEASE help me! Thanks you guys! Quote Link to comment Share on other sites More sharing options...
Sebkinne Posted October 27, 2013 Share Posted October 27, 2013 This is interesting. Please post your /etc/config/wireless I have seen quite a few people that seem to have wlan0 and wlan1 switch places. Let's see if it is to do with the radio enumeration. Quote Link to comment Share on other sites More sharing options...
Draconem Posted October 27, 2013 Author Share Posted October 27, 2013 My pineapple now works in client mode (and with wlan1) ! In IRC you told me a command then i rebooted and it fixed the problem DNS spoof and Karma is still not working tough :/ Quote Link to comment Share on other sites More sharing options...
Tommo Posted October 27, 2013 Share Posted October 27, 2013 (edited) Since the recent update, my Mark V won't connect as a client either. Worked fine, updated everything, rebooted, and now it won't connect. It also appears Karma clients can't connect now either (they can see the networks created, just not connect to them). :( EDIT: I had to use the Wifi Manager infusion to get it to connect as a client. Edited October 27, 2013 by Tommo Quote Link to comment Share on other sites More sharing options...
Foxtrot Posted October 28, 2013 Share Posted October 28, 2013 A fix is on the way, Me and Sebkinne have been working hard to find the problem and the issue seems to have been located. Quote Link to comment Share on other sites More sharing options...
Ianspeed Posted October 29, 2013 Share Posted October 29, 2013 Same here I belive. SSID list is reluctant to appear (only after a handfull of refreshes) and client mode has not so far allowed any traffic over the link. No change with a full reset. Happy to contribute if you need any debug info. Quote Link to comment Share on other sites More sharing options...
shoeless89 Posted October 29, 2013 Share Posted October 29, 2013 A fix is on the way, Me and Sebkinne have been working hard to find the problem and the issue seems to have been located. You can do it! Quote Link to comment Share on other sites More sharing options...
tanch Posted November 16, 2013 Share Posted November 16, 2013 My pineapple now works in client mode (and with wlan1) ! In IRC you told me a command then i rebooted and it fixed the problem DNS spoof and Karma is still not working tough :/ Hi there. Please share the command to fix client mode problem. I'm having the same issue. Thanks in adv. Quote Link to comment Share on other sites More sharing options...
Sebkinne Posted November 16, 2013 Share Posted November 16, 2013 Hi there. Please share the command to fix client mode problem. I'm having the same issue. Thanks in adv. Update to 1.0.1 firmware, update all infusions in the bar and it will work. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.