Jump to content

Mark IV and 3G HUAWEI 1750 + microSD 2GB - Not mounting SD partitions

d1000

By d1000
in WiFi Pineapple Mark IV

 Share

Recommended Posts

d1000 Newbie

d1000

Posted
Posted
Hi folks, i'm using my huawei 1750 with a simple 2GB microsd card and couldn't mount the sd partitions. I follow Darren thread preparing the sd partitions and also tried some inputs from other members in that thread. Any help will be much appreciated.


Pineapple Hardware Version (ex: Mark III, Mark IV, etc.): MK4

Pineapple Software Version (ex: 2.5.0, 2.6.4): 2.7.1

OS used to connect to the pineapple: Win8

All the tools/options that are running on the pineapple when the issue happened: Stock

Ping results from computer to pineapple: OK

Is the problem repeatable (Yes/No): Yes

Steps taken which created the problem: Just plug the hauwei 1750 with 2gb sd card, and dont mount the two EXT4 partitions

Error Messages: Dont find any

Log file information: Above in spoiler

Anything else that was attempted to 'fix' the problem: Follow the Darren's thread http://forums.hak5.org/index.php?/topic/25882-how-to-enable-usb-mass-storage-with-swap-partition/ and also modified to sg0 and sg1 where sda1 and sd2 were (also not working)


Disk Usage


Filesystem Size Used Available Use% Mounted on

rootfs 1.0M 244.0K 780.0K 24% /

/dev/root 5.0M 5.0M 0 100% /rom

tmpfs 14.3M 112.0K 14.2M 1% /tmp

tmpfs 512.0K 0 512.0K 0% /dev

/dev/mtdblock3 1.0M 244.0K 780.0K 24% /overlay

overlayfs:/overlay 1.0M 244.0K 780.0K 24% /

MISSING SD1 and SD2 (two EXT4 partitions in 2GB SD card)




Execute: ls /dev/s*


/dev/sda

/dev/sg0

/dev/sg1


/dev/shm:




fstab Configuration


config global automount

option from_fstab 1

option anon_mount 1


config global autoswap

option from_fstab 1

option anon_swap 0


config mount

option target /usb

option device /dev/sg0

option fstype ext4

option options rw,sync

option enabled 1

option enabled_fsck 0


config swap

option device /dev/sg1

option enabled 0




lsusb Output


Bus 001 Device 011: ID 12d1:1001 Huawei Technologies Co., Ltd. E169/E620/E800 HSDPA Modem

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub



Execute: dmesg


[ 0.000000] Linux version 3.6.11 (sebkinne@nimbus) (gcc version 4.6.4 20121106 (prerelease) (Linaro GCC 4.6-2012.11) ) #23 Wed Jan 9 18:08:46 GMT 2013

[ 0.000000] MyLoader: sysp=00020004, boardp=80250204, parts=20004319

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)

[ 0.000000] SoC: Atheros AR9330 rev 1

[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 02000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Zone ranges:

[ 0.000000] Normal [mem 0x00000000-0x01ffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]

[ 0.000000] On node 0 totalpages: 8192

[ 0.000000] free_area_init_node: node 0, pgdat 802d1340, node_mem_map 81000000

[ 0.000000] Normal zone: 64 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 8128 pages, LIFO batch:0

[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768

[ 0.000000] pcpu-alloc: [0] 0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128

[ 0.000000] Kernel command line: board=HORNET-UB console=ttyATH0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6144k(rootfs),1600k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd

[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)

[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] __ex_table already sorted, skipping sort

[ 0.000000] Writing ErrCtl register=00000000

[ 0.000000] Readback ErrCtl register=00000000

[ 0.000000] Memory: 29132k/32768k available (2105k kernel code, 3636k reserved, 396k data, 212k init, 0k highmem)

[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] NR_IRQS:51

[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)

[ 0.080000] pid_max: default: 32768 minimum: 301

[ 0.080000] Mount-cache hash table entries: 512

[ 0.090000] NET: Registered protocol family 16

[ 0.090000] MIPS: machine is ALFA NETWORKS Hornet-UB

[ 0.550000] bio: create slab at 0

[ 0.550000] Switching to clocksource MIPS

[ 0.560000] NET: Registered protocol family 2

[ 0.560000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)

[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)

[ 0.580000] TCP: reno registered

[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.600000] NET: Registered protocol family 1

[ 0.600000] PCI: CLS 0 bytes, default 32

[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.

[ 0.630000] msgmni has been set to 56

[ 0.640000] io scheduler noop registered

[ 0.640000] io scheduler deadline registered (default)

[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

[ 0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART

[ 0.660000] console [ttyATH0] enabled, bootconsole disabled

[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated

[ 0.680000] m25p80 spi0.0: found mx25l6405d, expected m25p80

[ 0.680000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)

[ 0.690000] 7 cmdlinepart partitions found on MTD device spi0.0

[ 0.690000] Creating 7 MTD partitions on "spi0.0":

[ 0.700000] 0x000000000000-0x000000040000 : "u-boot"

[ 0.710000] 0x000000040000-0x000000050000 : "u-boot-env"

[ 0.710000] 0x000000050000-0x000000650000 : "rootfs"

[ 0.720000] mtd: partition "rootfs" set to be root filesystem

[ 0.720000] mtd: partition "rootfs_data" created automatically, ofs=550000, len=100000

[ 0.730000] 0x000000550000-0x000000650000 : "rootfs_data"

[ 0.740000] 0x000000650000-0x0000007e0000 : "kernel"

[ 0.740000] 0x0000007e0000-0x0000007f0000 : "nvram"

[ 0.750000] 0x0000007f0000-0x000000800000 : "art"

[ 0.750000] 0x000000050000-0x0000007e0000 : "firmware"

[ 0.780000] libphy: ag71xx_mdio: probed

[ 0.780000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII

[ 1.340000] eth0: Found an AR7240/AR9330 built-in switch

[ 2.370000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII

[ 2.920000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]

[ 2.930000] TCP: cubic registered

[ 2.930000] NET: Registered protocol family 17

[ 2.940000] 8021q: 802.1Q VLAN Support v1.8

[ 2.950000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.

[ 2.960000] Freeing unused kernel memory: 212k freed

[ 6.350000] Registered led device: alfa:blue:lan

[ 6.350000] Registered led device: alfa:blue:usb

[ 6.350000] Registered led device: alfa:blue:wan

[ 6.350000] Registered led device: alfa:blue:wlan

[ 6.350000] Registered led device: alfa:blue:wps

[ 9.670000] jffs2: notice: (458) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 13 of xref (0 dead, 5 orphan) found.

[ 10.430000] SCSI subsystem initialized

[ 10.730000] usbcore: registered new interface driver usbfs

[ 10.740000] usbcore: registered new interface driver hub

[ 10.740000] usbcore: registered new device driver usb

[ 11.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 11.350000] ehci-platform ehci-platform: Generic Platform EHCI Controller

[ 11.360000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1

[ 11.400000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000

[ 11.420000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00

[ 11.420000] hub 1-0:1.0: USB hub found

[ 11.420000] hub 1-0:1.0: 1 port detected

[ 11.540000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 11.660000] uhci_hcd: USB Universal Host Controller Interface driver

[ 11.780000] Initializing USB Mass Storage driver...

[ 11.780000] usbcore: registered new interface driver usb-storage

[ 11.790000] USB Mass Storage support registered.

[ 11.890000] usb 1-1: new high-speed USB device number 2 using ehci-platform

[ 12.040000] scsi0 : usb-storage 1-1:1.0

[ 12.050000] scsi1 : usb-storage 1-1:1.1

[ 13.040000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 13.050000] scsi 1:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 13.060000] sd 1:0:0:0: [sda] Attached SCSI removable disk

[ 33.370000] Compat-drivers backport release: compat-drivers-2012-12-04

[ 33.370000] Backport based on wireless-testing.git master-2012-12-06

[ 33.380000] compat.git: wireless-testing.git

[ 33.420000] cfg80211: Calling CRDA to update world regulatory domain

[ 33.420000] cfg80211: World regulatory domain updated:

[ 33.430000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 33.430000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 33.440000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 33.450000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 33.460000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 33.460000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.380000] cfg80211: World regulatory domain updated:

[ 34.380000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 34.390000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.400000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 34.410000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 34.420000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.420000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.910000] usbcore: registered new interface driver rt73usb

[ 35.060000] usbcore: registered new interface driver rtl8187

[ 35.100000] ath: EEPROM regdomain: 0x833a

[ 35.100000] ath: EEPROM indicates we should expect a country code

[ 35.100000] ath: doing EEPROM country->regdmn map search

[ 35.100000] ath: country maps to regdmn code: 0x37

[ 35.100000] ath: Country alpha2 being used: GB

[ 35.100000] ath: Regpair used: 0x37

[ 35.100000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

[ 35.100000] Registered led device: ath9k-phy0

[ 35.100000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2

[ 35.130000] usbcore: registered new interface driver rt2800usb

[ 35.210000] Button Hotplug driver version 0.4.1

[ 35.230000] cfg80211: Calling CRDA for country: GB

[ 35.230000] cfg80211: Regulatory domain changed to country: GB

[ 35.230000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 35.240000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[ 35.250000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[ 35.260000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[ 35.260000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)

[ 35.510000] RPC: Registered named UNIX socket transport module.

[ 35.510000] RPC: Registered udp transport module.

[ 35.520000] RPC: Registered tcp transport module.

[ 35.520000] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 35.870000] PPP generic driver version 2.4.2

[ 36.000000] tun: Universal TUN/TAP device driver, 1.6

[ 36.010000] tun: © 1999-2004 Max Krasnyansky

[ 36.300000] ip_tables: © 2000-2006 Netfilter Core Team

[ 36.540000] NET: Registered protocol family 24

[ 36.680000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)

[ 37.540000] usbcore: registered new interface driver ath9k_htc

[ 37.810000] usbcore: registered new interface driver usbserial

[ 37.810000] usbcore: registered new interface driver usbserial_generic

[ 37.820000] USB Serial support registered for generic

[ 37.820000] usbserial: USB Serial Driver core

[ 37.870000] usbcore: registered new interface driver cdc_ether

[ 37.980000] Error: Driver 'gpio-keys-polled' is already registered, aborting...

[ 38.100000] usbcore: registered new interface driver rndis_host

[ 38.230000] scsi 0:0:0:0: Attached scsi generic sg0 type 5

[ 38.240000] sd 1:0:0:0: Attached scsi generic sg1 type 0

[ 41.940000] usb 1-1: USB disconnect, device number 2

[ 44.290000] device eth0 entered promiscuous mode

[ 46.710000] usb 1-1: new high-speed USB device number 3 using ehci-platform

[ 46.870000] scsi5 : usb-storage 1-1:1.3

[ 46.870000] scsi6 : usb-storage 1-1:1.4

[ 47.690000] device wlan0 entered promiscuous mode

[ 47.770000] br-lan: port 2(wlan0) entered forwarding state

[ 47.770000] br-lan: port 2(wlan0) entered forwarding state

[ 47.870000] scsi 5:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 47.870000] scsi 5:0:0:0: Attached scsi generic sg0 type 5

[ 47.880000] scsi 6:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 47.890000] sd 6:0:0:0: Attached scsi generic sg1 type 0

[ 47.900000] sd 6:0:0:0: [sda] Attached SCSI removable disk

[ 49.770000] br-lan: port 2(wlan0) entered forwarding state

[ 57.860000] device wlan0 left promiscuous mode

[ 57.860000] br-lan: port 2(wlan0) entered disabled state

[ 58.910000] device wlan0 entered promiscuous mode

[ 59.000000] br-lan: port 2(wlan0) entered forwarding state

[ 59.000000] br-lan: port 2(wlan0) entered forwarding state

[ 59.210000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x02000020 DMADBG_7=0x00026e00

[ 59.220000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up

[ 61.000000] br-lan: port 2(wlan0) entered forwarding state

[ 73.980000] USB Serial deregistering driver generic

[ 73.980000] usbcore: deregistering interface driver usbserial_generic

[ 73.990000] usbcore: deregistering interface driver usbserial

[ 77.020000] usbcore: registered new interface driver usbserial

[ 77.030000] usbcore: registered new interface driver usbserial_generic

[ 77.040000] USB Serial support registered for generic

[ 77.040000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 77.050000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 77.060000] usbserial_generic 1-1:1.0: generic converter detected

[ 77.070000] usb 1-1: generic converter now attached to ttyUSB0

[ 77.070000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 77.080000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 77.090000] usbserial_generic 1-1:1.1: generic converter detected

[ 77.100000] usb 1-1: generic converter now attached to ttyUSB1

[ 77.100000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 77.120000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 77.120000] usbserial_generic 1-1:1.2: generic converter detected

[ 77.130000] usb 1-1: generic converter now attached to ttyUSB2

[ 77.140000] usbserial: USB Serial Driver core

[ 755.990000] usb 1-1: USB disconnect, device number 3

[ 756.000000] generic ttyUSB0: generic converter now disconnected from ttyUSB0

[ 756.000000] usbserial_generic 1-1:1.0: device disconnected

[ 756.010000] generic ttyUSB1: generic converter now disconnected from ttyUSB1

[ 756.020000] usbserial_generic 1-1:1.1: device disconnected

[ 756.020000] generic ttyUSB2: generic converter now disconnected from ttyUSB2

[ 756.030000] usbserial_generic 1-1:1.2: device disconnected

[ 762.930000] usb 1-1: new high-speed USB device number 4 using ehci-platform

[ 763.080000] scsi7 : usb-storage 1-1:1.0

[ 763.100000] scsi8 : usb-storage 1-1:1.1

[ 763.650000] usb 1-1: USB disconnect, device number 4

[ 768.600000] usb 1-1: new high-speed USB device number 5 using ehci-platform

[ 768.750000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 768.760000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 768.770000] usbserial_generic 1-1:1.0: generic converter detected

[ 768.780000] usb 1-1: generic converter now attached to ttyUSB0

[ 768.780000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 768.790000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 768.800000] usbserial_generic 1-1:1.1: generic converter detected

[ 768.810000] usb 1-1: generic converter now attached to ttyUSB1

[ 768.820000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 768.820000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 768.830000] usbserial_generic 1-1:1.2: generic converter detected

[ 768.840000] usb 1-1: generic converter now attached to ttyUSB2

[ 768.850000] scsi12 : usb-storage 1-1:1.3

[ 768.860000] scsi13 : usb-storage 1-1:1.4

[ 769.850000] scsi 12:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 769.850000] scsi 12:0:0:0: Attached scsi generic sg0 type 5

[ 769.860000] scsi 13:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 769.870000] sd 13:0:0:0: Attached scsi generic sg1 type 0

[ 769.890000] sd 13:0:0:0: [sda] Attached SCSI removable disk

[ 1012.150000] usb 1-1: USB disconnect, device number 5

[ 1012.150000] generic ttyUSB0: generic converter now disconnected from ttyUSB0

[ 1012.160000] usbserial_generic 1-1:1.0: device disconnected

[ 1012.170000] generic ttyUSB1: generic converter now disconnected from ttyUSB1

[ 1012.170000] usbserial_generic 1-1:1.1: device disconnected

[ 1012.180000] generic ttyUSB2: generic converter now disconnected from ttyUSB2

[ 1012.190000] usbserial_generic 1-1:1.2: device disconnected

[ 1186.780000] usb 1-1: new high-speed USB device number 6 using ehci-platform

[ 1186.930000] scsi14 : usb-storage 1-1:1.0

[ 1186.950000] scsi15 : usb-storage 1-1:1.1

[ 1187.150000] usb 1-1: USB disconnect, device number 6

[ 1191.450000] usb 1-1: new high-speed USB device number 7 using ehci-platform

[ 1191.600000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1191.610000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1191.620000] usbserial_generic 1-1:1.0: generic converter detected

[ 1191.630000] usb 1-1: generic converter now attached to ttyUSB0

[ 1191.630000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1191.640000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1191.650000] usbserial_generic 1-1:1.1: generic converter detected

[ 1191.660000] usb 1-1: generic converter now attached to ttyUSB1

[ 1191.670000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1191.670000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1191.680000] usbserial_generic 1-1:1.2: generic converter detected

[ 1191.690000] usb 1-1: generic converter now attached to ttyUSB2

[ 1191.710000] scsi19 : usb-storage 1-1:1.3

[ 1191.710000] scsi20 : usb-storage 1-1:1.4

[ 1192.710000] scsi 19:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 1192.710000] scsi 19:0:0:0: Attached scsi generic sg0 type 5

[ 1192.720000] scsi 20:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 1192.730000] sd 20:0:0:0: Attached scsi generic sg1 type 0

[ 1192.740000] sd 20:0:0:0: [sda] Attached SCSI removable disk

[ 1210.790000] USB Serial deregistering driver generic

[ 1210.800000] generic ttyUSB2: generic converter now disconnected from ttyUSB2

[ 1210.800000] generic ttyUSB1: generic converter now disconnected from ttyUSB1

[ 1210.810000] generic ttyUSB0: generic converter now disconnected from ttyUSB0

[ 1210.820000] usbcore: deregistering interface driver usbserial_generic

[ 1210.820000] usbserial_generic 1-1:1.2: device disconnected

[ 1210.830000] usbserial_generic 1-1:1.1: device disconnected

[ 1210.830000] usbserial_generic 1-1:1.0: device disconnected

[ 1210.840000] usbcore: deregistering interface driver usbserial

[ 1213.990000] usbcore: registered new interface driver usbserial

[ 1214.000000] usbcore: registered new interface driver usbserial_generic

[ 1214.000000] USB Serial support registered for generic

[ 1214.010000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1214.020000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1214.030000] usbserial_generic 1-1:1.0: generic converter detected

[ 1214.040000] usb 1-1: generic converter now attached to ttyUSB0

[ 1214.040000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1214.050000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1214.060000] usbserial_generic 1-1:1.1: generic converter detected

[ 1214.070000] usb 1-1: generic converter now attached to ttyUSB1

[ 1214.070000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1214.080000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1214.090000] usbserial_generic 1-1:1.2: generic converter detected

[ 1214.100000] usb 1-1: generic converter now attached to ttyUSB2

[ 1214.110000] usbserial: USB Serial Driver core

[ 1431.040000] usb 1-1: USB disconnect, device number 7

[ 1431.050000] generic ttyUSB0: generic converter now disconnected from ttyUSB0

[ 1431.050000] usbserial_generic 1-1:1.0: device disconnected

[ 1431.060000] generic ttyUSB1: generic converter now disconnected from ttyUSB1

[ 1431.070000] usbserial_generic 1-1:1.1: device disconnected

[ 1431.070000] generic ttyUSB2: generic converter now disconnected from ttyUSB2

[ 1431.080000] usbserial_generic 1-1:1.2: device disconnected

[ 1439.680000] usb 1-1: new high-speed USB device number 8 using ehci-platform

[ 1439.830000] scsi21 : usb-storage 1-1:1.0

[ 1439.850000] scsi22 : usb-storage 1-1:1.1

[ 1440.050000] usb 1-1: USB disconnect, device number 8

[ 1444.340000] usb 1-1: new high-speed USB device number 9 using ehci-platform

[ 1444.490000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1444.500000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1444.510000] usbserial_generic 1-1:1.0: generic converter detected

[ 1444.520000] usb 1-1: generic converter now attached to ttyUSB0

[ 1444.530000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1444.530000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1444.540000] usbserial_generic 1-1:1.1: generic converter detected

[ 1444.550000] usb 1-1: generic converter now attached to ttyUSB1

[ 1444.570000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 1444.580000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 1444.580000] usbserial_generic 1-1:1.2: generic converter detected

[ 1444.590000] usb 1-1: generic converter now attached to ttyUSB2

[ 1444.610000] scsi26 : usb-storage 1-1:1.3

[ 1444.610000] scsi27 : usb-storage 1-1:1.4

[ 1445.610000] scsi 26:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 1445.620000] scsi 26:0:0:0: Attached scsi generic sg0 type 5

[ 1445.620000] scsi 27:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 1445.630000] sd 27:0:0:0: Attached scsi generic sg1 type 0

[ 1445.640000] sd 27:0:0:0: [sda] Attached SCSI removable disk



System Log


10:17:47 Pineapple user.info autossh[5331]: starting ssh (count 10)

10:17:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:17:47 Pineapple user.info autossh[5331]: ssh child pid is 5578

10:17:15 Pineapple user.info autossh[5331]: starting ssh (count 9)

10:17:15 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:17:15 Pineapple user.info autossh[5331]: ssh child pid is 5575

10:17:06 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:05 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:04 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:03 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:02 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:01 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:00 Pineapple user.notice usb-modeswitch: 1-1:1.4: Switching seemingly failed

10:17:00 Pineapple user.notice usb-modeswitch: 1-1:1.4: Selecting /etc/usb_modeswitch.d/12d1:1001 for mode switching

10:17:00 Pineapple user.notice usb-modeswitch: 1-1:1.4: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:16:58 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:57 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:57 Pineapple user.info autossh[5331]: starting ssh (count 8)

10:16:57 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:57 Pineapple user.info autossh[5331]: ssh child pid is 5421

10:16:56 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:55 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:54 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:53 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:52 Pineapple user.notice usb-modeswitch: 1-1:1.3: Switching seemingly failed

10:16:52 Pineapple user.notice usb-modeswitch: 1-1:1.3: Selecting /etc/usb_modeswitch.d/12d1:1001 for mode switching

10:16:52 Pineapple user.notice usb-modeswitch: 1-1:1.3: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:16:51 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:50 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:49 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:49 Pineapple user.info autossh[5331]: starting ssh (count 7)

10:16:49 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:49 Pineapple user.info autossh[5331]: ssh child pid is 5360

10:16:49 Pineapple daemon.info dnsmasq[1093]: using nameserver 88.214.182.1#53

10:16:49 Pineapple daemon.info dnsmasq[1093]: using nameserver 88.214.178.2#53

10:16:49 Pineapple daemon.info dnsmasq[1093]: using nameserver 8.8.8.8#53

10:16:49 Pineapple daemon.info dnsmasq[1093]: using local addresses only for domain lan

10:16:49 Pineapple daemon.info dnsmasq[1093]: reading /tmp/resolv.conf.auto

10:16:48 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:47 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:47 Pineapple user.info autossh[5331]: starting ssh (count 6)

10:16:47 Pineapple user.info autossh[5331]: starting ssh (count 5)

10:16:47 Pineapple user.info autossh[5331]: starting ssh (count 4)

10:16:47 Pineapple user.info autossh[5331]: starting ssh (count 3)

10:16:47 Pineapple user.info autossh[5331]: starting ssh (count 2)

10:16:47 Pineapple user.info autossh[5331]: starting ssh (count 1)

10:16:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:47 Pineapple user.info autossh[5331]: ssh exited with error status 1; restarting ssh

10:16:47 Pineapple user.info autossh[5331]: ssh child pid is 5337

10:16:47 Pineapple user.info autossh[5331]: ssh child pid is 5336

10:16:47 Pineapple user.info autossh[5331]: ssh child pid is 5335

10:16:47 Pineapple user.info autossh[5331]: ssh child pid is 5334

10:16:47 Pineapple user.info autossh[5331]: ssh child pid is 5333

10:16:47 Pineapple user.info autossh[5331]: ssh child pid is 5332

10:16:46 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:46 Pineapple daemon.warn pppd[5247]: Could not determine remote IP address: defaulting to 10.64.64.64

10:16:46 Pineapple daemon.notice pppd[5247]: secondary DNS address 88.214.182.1

10:16:46 Pineapple daemon.notice pppd[5247]: remote IP address 10.64.64.64

10:16:46 Pineapple daemon.notice pppd[5247]: primary DNS address 88.214.178.2

10:16:46 Pineapple daemon.notice pppd[5247]: local IP address 46.50.27.46

10:16:46 Pineapple daemon.notice netifd: Interface 'wan2' is now up

10:16:45 Pineapple user.notice usb-modeswitch: 1-1:1.2: Switching seemingly failed

10:16:45 Pineapple user.notice usb-modeswitch: 1-1:1.2: Selecting /etc/usb_modeswitch.d/12d1:1001 for mode switching

10:16:45 Pineapple user.notice usb-modeswitch: 1-1:1.2: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:16:43 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:43 Pineapple daemon.notice pppd[5247]: CHAP authentication succeeded

10:16:43 Pineapple daemon.info pppd[5247]: CHAP authentication succeeded

10:16:42 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:42 Pineapple daemon.notice pppd[5247]: Connect: 3g-wan2 <--> /dev/ttyUSB0

10:16:42 Pineapple daemon.info pppd[5247]: Using interface 3g-wan2

10:16:41 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:41 Pineapple local2.info chat[5256]: timeout set to 30 seconds

10:16:41 Pineapple local2.info chat[5256]: timeout set to 10 seconds

10:16:41 Pineapple local2.info chat[5256]: send (ATE1^M)

10:16:41 Pineapple local2.info chat[5256]: send (ATD*99***1#^M)

10:16:41 Pineapple local2.info chat[5256]: send (AT+CGDCONT=1,"IP","internet"^M)

10:16:41 Pineapple local2.info chat[5256]: send (AT&F^M)

10:16:41 Pineapple local2.info chat[5256]: send ( ^M)

10:16:41 Pineapple local2.info chat[5256]: report (CONNECT)

10:16:41 Pineapple local2.info chat[5256]: expect (OK)

10:16:41 Pineapple local2.info chat[5256]: expect (OK)

10:16:41 Pineapple local2.info chat[5256]: expect (OK)

10:16:41 Pineapple local2.info chat[5256]: expect (CONNECT)

10:16:41 Pineapple local2.info chat[5256]: abort on (NO CARRIER)

10:16:41 Pineapple local2.info chat[5256]: abort on (ERROR)

10:16:41 Pineapple local2.info chat[5256]: abort on (BUSY)

10:16:41 Pineapple local2.info chat[5256]: ^M

10:16:41 Pineapple local2.info chat[5256]: ^M

10:16:41 Pineapple local2.info chat[5256]: ^M

10:16:41 Pineapple local2.info chat[5256]: OK

10:16:41 Pineapple local2.info chat[5256]: OK

10:16:41 Pineapple local2.info chat[5256]: OK

10:16:41 Pineapple local2.info chat[5256]: CONNECT

10:16:41 Pineapple local2.info chat[5256]: ATE1^M^M

10:16:41 Pineapple local2.info chat[5256]: ATD*99***1#^M^M

10:16:41 Pineapple local2.info chat[5256]: AT+CGDCONT=1,"IP","internet"^M^M

10:16:41 Pineapple local2.info chat[5256]: AT&F^M^M

10:16:41 Pineapple local2.info chat[5256]: -- got it

10:16:41 Pineapple local2.info chat[5256]: -- got it

10:16:41 Pineapple local2.info chat[5256]: -- got it

10:16:41 Pineapple local2.info chat[5256]: -- got it

10:16:41 Pineapple daemon.info pppd[5247]: Serial connection established.

10:16:40 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:40 Pineapple daemon.notice pppd[5247]: pppd 2.4.5 started by root, uid 0

10:16:39 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:39 Pineapple daemon.notice netifd: wan2 (5203): Trying to set mode

10:16:38 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:37 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:37 Pineapple user.notice usb-modeswitch: 1-1:1.1: Selecting /etc/usb_modeswitch.d/12d1:1001 for mode switching

10:16:37 Pineapple user.notice usb-modeswitch: 1-1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:16:36 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:35 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:34 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:33 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:32 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:31 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:30 Pineapple user.notice usb-modeswitch: 1-1:1.0: Switching seemingly failed

10:16:30 Pineapple user.notice usb-modeswitch: 1-1:1.0: Selecting /etc/usb_modeswitch.d/12d1:1001 for mode switching

10:16:30 Pineapple user.notice usb-modeswitch: 1-1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:16:28 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:27 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:26 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:25 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:24 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:23 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:22 Pineapple user.notice usb-modeswitch: 1-1:1.1: Switching seemingly failed

10:16:22 Pineapple user.notice usb-modeswitch: 1-1:1.1: Selecting /etc/usb_modeswitch.d/12d1:1001 for mode switching

10:16:22 Pineapple user.notice usb-modeswitch: 1-1:1.1: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:16:05 Pineapple daemon.info dnsmasq[1093]: using nameserver 8.8.8.8#53

10:16:05 Pineapple daemon.info dnsmasq[1093]: using local addresses only for domain lan

10:16:05 Pineapple daemon.info dnsmasq[1093]: reading /tmp/resolv.conf.auto

10:15:57 Pineapple kern.notice kernel: [ 1855.510000] sd 34:0:0:0: [sda] Attached SCSI removable disk

10:15:57 Pineapple kern.notice kernel: [ 1855.500000] sd 34:0:0:0: Attached scsi generic sg1 type 0

10:15:57 Pineapple kern.notice kernel: [ 1855.490000] scsi 34:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

10:15:57 Pineapple kern.notice kernel: [ 1855.480000] scsi 33:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

10:15:57 Pineapple kern.notice kernel: [ 1855.480000] scsi 33:0:0:0: Attached scsi generic sg0 type 5

10:15:56 Pineapple kern.info kernel: [ 1854.480000] scsi34 : usb-storage 1-1:1.4

10:15:56 Pineapple kern.info kernel: [ 1854.480000] scsi33 : usb-storage 1-1:1.3

10:15:56 Pineapple kern.info kernel: [ 1854.460000] usbserial_generic 1-1:1.2: generic converter detected

10:15:56 Pineapple kern.info kernel: [ 1854.460000] usb 1-1: generic converter now attached to ttyUSB2

10:15:56 Pineapple kern.info kernel: [ 1854.450000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

10:15:56 Pineapple kern.info kernel: [ 1854.440000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

10:15:56 Pineapple kern.info kernel: [ 1854.430000] usb 1-1: generic converter now attached to ttyUSB1

10:15:56 Pineapple kern.info kernel: [ 1854.420000] usbserial_generic 1-1:1.1: generic converter detected

10:15:56 Pineapple kern.info kernel: [ 1854.410000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

10:15:56 Pineapple kern.info kernel: [ 1854.400000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

10:15:56 Pineapple kern.info kernel: [ 1854.400000] usb 1-1: generic converter now attached to ttyUSB0

10:15:56 Pineapple kern.info kernel: [ 1854.390000] usbserial_generic 1-1:1.0: generic converter detected

10:15:56 Pineapple kern.info kernel: [ 1854.380000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

10:15:55 Pineapple kern.info kernel: [ 1854.370000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

10:15:55 Pineapple kern.info kernel: [ 1854.220000] usb 1-1: new high-speed USB device number 11 using ehci-platform

10:15:51 Pineapple user.notice usb-modeswitch: 1-1:1.0: Selecting /etc/usb_modeswitch.d/12d1:1446 for mode switching

10:15:51 Pineapple user.notice usb-modeswitch: 1-1:1.0: Manufacturer=HUAWEI_Technology Product=HUAWEI_Mobile Serial=?

10:15:51 Pineapple syslog.notice usb_modeswitch: switching device 12d1:1446 on 001/010

10:15:51 Pineapple kern.info kernel: [ 1849.920000] usb 1-1: USB disconnect, device number 10

10:15:51 Pineapple kern.info kernel: [ 1849.720000] scsi29 : usb-storage 1-1:1.1

10:15:51 Pineapple kern.info kernel: [ 1849.700000] scsi28 : usb-storage 1-1:1.0

10:15:51 Pineapple kern.info kernel: [ 1849.550000] usb 1-1: new high-speed USB device number 10 using ehci-platform

10:15:44 Pineapple user.info autossh[4516]: starting ssh (count 14)

10:15:44 Pineapple user.info autossh[4516]: ssh exited with error status 1; restarting ssh

10:15:44 Pineapple user.info autossh[4516]: ssh child pid is 4961

10:15:44 Pineapple daemon.notice netifd: Interface 'wan2' is now down

10:15:44 Pineapple daemon.info pppd[4432]: Terminating on signal 15

10:15:44 Pineapple daemon.info pppd[4432]: Exit.

10:15:43 Pineapple kern.info kernel: [ 1842.080000] usbserial_generic 1-1:1.2: device disconnected

10:15:43 Pineapple kern.info kernel: [ 1842.080000] generic ttyUSB2: generic converter now disconnected from ttyUSB2

10:15:43 Pineapple kern.info kernel: [ 1842.070000] usbserial_generic 1-1:1.1: device disconnected

10:15:43 Pineapple kern.info kernel: [ 1842.060000] usbserial_generic 1-1:1.0: device disconnected

10:15:43 Pineapple kern.info kernel: [ 1842.060000] generic ttyUSB1: generic converter now disconnected from ttyUSB1

10:15:43 Pineapple kern.info kernel: [ 1842.050000] generic ttyUSB0: generic converter now disconnected from ttyUSB0

10:15:43 Pineapple daemon.notice pppd[4432]: Connection terminated.

10:15:43 Pineapple daemon.notice netifd: Interface 'wan2' has lost the connection

10:15:43 Pineapple daemon.info pppd[4432]: Sent 106239 bytes, received 102921 bytes.

10:15:43 Pineapple daemon.info pppd[4432]: Connect time 5.8 minutes.



Link to comment
Share on other sites
d1000 Newbie

d1000

Posted
  • Author
Posted

in dmesg i find the follow:

[ 38.470000] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 38.480000] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 42.430000] usb 1-1: USB disconnect, device number 2
[ 44.930000] device eth0 entered promiscuous mode
[ 47.360000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 47.520000] scsi5 : usb-storage 1-1:1.3
[ 47.520000] scsi6 : usb-storage 1-1:1.4
[ 48.330000] device wlan0 entered promiscuous mode
[ 48.410000] br-lan: port 2(wlan0) entered forwarding state
[ 48.410000] br-lan: port 2(wlan0) entered forwarding state
[ 48.520000] scsi 5:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 48.520000] scsi 5:0:0:0: Attached scsi generic sg0 type 5
[ 48.530000] scsi 6:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2
[ 48.540000] sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 48.550000] sd 6:0:0:0: [sda] Attached SCSI removable disk


Link to comment
Share on other sites
d1000 Newbie

d1000

Posted
  • Author
Posted
Not sure whats going on but looks like (from dmesg and /dev/s*) that the sdcard is mapping to /dev/sda, im not seeing any partitions.

Can you try to mount /dev/sda ? or fdisk /dev/sda?

mount using the fstab conf?

Like this?

config global automount

option from_fstab 1

option anon_mount 1

config global autoswap

option from_fstab 1

option anon_swap 0

config mount

option target /usb

option device /dev/sda

option fstype ext4

option options rw,sync

option enabled 1

option enabled_fsck 0

config swap

option device /dev/sg1

option enabled 0

Link to comment
Share on other sites
no42 Newbie

no42

Posted
Posted

Sorry I wasnt clear earlier.

Can you either mount the sda drive on the pineapple / another linux OS.

it looks like the sdcard is assigned to /dev/sda, it could be 1 large partition or it could be that the sdcard is not formatted.

commands:

mkdir /mnt/test

mount /dev/sda /mnt/test

or

fdisk /dev/sda

> p
Link to comment
Share on other sites
d1000 Newbie

d1000

Posted
  • Author
Posted (edited)

1 - I plug to Linux and the volumes appear mounted stable
2 - I unmounted the volumes
3 - Plug to MK4 with same fstab config, they mount and appear in resources, but could use to install or appear as valid location when you choose to install infusions/modules.

Bring the pen to Linux again, in fdisk and disk utility appears like this:

21d21rt.png

33xhetz.png

Also tried to mount volumes and move to MK4, and unmount volumes and move to MK4, same behavior...


I don't understand...

Edited by d1000
Link to comment
Share on other sites
no42 Newbie

no42

Posted
Posted

hmm, my mate hasn't returned my pineapple, to see if i can duplicate your results - odd.

For the moment I'm stuck! and cant fathom it; maybe some-other pineapple expert can spot something i missed?

Link to comment
Share on other sites
d1000 Newbie

d1000

Posted
  • Author
Posted
hmm, my mate hasn't returned my pineapple, to see if i can duplicate your results - odd.

For the moment I'm stuck! and cant fathom it; maybe some-other pineapple expert can spot something i missed?

:) thxs midS!

Will wait for further inputs or experiences? I'm stuck over here. Will try next week using an Anker + usb hub + pen drive + pen 3 without microsd, juicing only Pineapple with 9V...

Cheers

Link to comment
Share on other sites
kevambert Newbie

kevambert

Posted
Posted (edited)

Did you try this in your Fstab to mount to /USB

config global automount

option from_fstab 1

option anon_mount 1

config global autoswap

option from_fstab 1

option anon_swap 1

config mount

option target /usb

option device /dev/sda

option fstype ext4

option options rw,sync

option enabled 1

option enabled_fsck 0

config mount

option target /usb

option device /dev/sda1

option fstype ext4

option options rw,sync

option enabled 1

option enabled_fsck 0

config swap

option device /dev/sda2

option enabled 1

Edited by kevambert
Link to comment
Share on other sites
d1000 Newbie

d1000

Posted
  • Author
Posted (edited)
Did you try this in your Fstab to mount to /USB

config global automount

option from_fstab 1

option anon_mount 1

config global autoswap

option from_fstab 1

option anon_swap 1

config mount

option target /usb

option device /dev/sda

option fstype ext4

option options rw,sync

option enabled 1

option enabled_fsck 0

config mount

option target /usb

option device /dev/sda1

option fstype ext4

option options rw,sync

option enabled 1

option enabled_fsck 0

config swap

option device /dev/sda2

option enabled 1

Well well well :)

Now it mounts the FIRST partition ONLY, almost there! I wonder why...

Disk Usage

Filesystem Size Used Available Use% Mounted onrootfs 896.0K 268.0K 628.0K 30% //dev/root 5.3M 5.3M 0 100% /romtmpfs 14.3M 120.0K 14.2M 1% /tmptmpfs 512.0K 0 512.0K 0% /dev/dev/mtdblock3 896.0K 268.0K 628.0K 30% /overlayoverlayfs:/overlay 896.0K 268.0K 628.0K 30% //dev/sda1 1.7G 40.8M 1.5G 3% /usb[/spoiler]

Execute: dmesg

[ 0.000000] Linux version 3.6.11 (sebkinne@nimbus) (gcc version 4.6.4 20121106 (prerelease) (Linaro GCC 4.6-2012.11) ) #24 Wed Jan 9 22:13:23 GMT 2013

[ 0.000000] MyLoader: sysp=00020004, boardp=80250204, parts=20004319

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)

[ 0.000000] SoC: Atheros AR9330 rev 1

[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 02000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Zone ranges:

[ 0.000000] Normal [mem 0x00000000-0x01ffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]

[ 0.000000] On node 0 totalpages: 8192

[ 0.000000] free_area_init_node: node 0, pgdat 802d1340, node_mem_map 81000000

[ 0.000000] Normal zone: 64 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 8128 pages, LIFO batch:0

[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768

[ 0.000000] pcpu-alloc: [0] 0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128

[ 0.000000] Kernel command line: board=HORNET-UB console=ttyATH0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6144k(rootfs),1600k(kernel),64k(nvram),64k(art)ro,7744k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd

[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)

[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] __ex_table already sorted, skipping sort

[ 0.000000] Writing ErrCtl register=00000000

[ 0.000000] Readback ErrCtl register=00000000

[ 0.000000] Memory: 29132k/32768k available (2105k kernel code, 3636k reserved, 396k data, 212k init, 0k highmem)

[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] NR_IRQS:51

[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)

[ 0.080000] pid_max: default: 32768 minimum: 301

[ 0.080000] Mount-cache hash table entries: 512

[ 0.090000] NET: Registered protocol family 16

[ 0.090000] MIPS: machine is ALFA NETWORKS Hornet-UB

[ 0.550000] bio: create slab at 0

[ 0.550000] Switching to clocksource MIPS

[ 0.560000] NET: Registered protocol family 2

[ 0.560000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)

[ 0.570000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.570000] TCP: Hash tables configured (established 1024 bind 1024)

[ 0.580000] TCP: reno registered

[ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.590000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.600000] NET: Registered protocol family 1

[ 0.600000] PCI: CLS 0 bytes, default 32

[ 0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.620000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc.

[ 0.630000] msgmni has been set to 56

[ 0.640000] io scheduler noop registered

[ 0.640000] io scheduler deadline registered (default)

[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

[ 0.650000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART

[ 0.660000] console [ttyATH0] enabled, bootconsole disabled

[ 0.670000] ath79-spi ath79-spi: master is unqueued, this is deprecated

[ 0.680000] m25p80 spi0.0: found mx25l6405d, expected m25p80

[ 0.680000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)

[ 0.690000] 7 cmdlinepart partitions found on MTD device spi0.0

[ 0.690000] Creating 7 MTD partitions on "spi0.0":

[ 0.700000] 0x000000000000-0x000000040000 : "u-boot"

[ 0.710000] 0x000000040000-0x000000050000 : "u-boot-env"

[ 0.710000] 0x000000050000-0x000000650000 : "rootfs"

[ 0.720000] mtd: partition "rootfs" set to be root filesystem

[ 0.720000] mtd: partition "rootfs_data" created automatically, ofs=570000, len=E0000

[ 0.730000] 0x000000570000-0x000000650000 : "rootfs_data"

[ 0.740000] 0x000000650000-0x0000007e0000 : "kernel"

[ 0.740000] 0x0000007e0000-0x0000007f0000 : "nvram"

[ 0.750000] 0x0000007f0000-0x000000800000 : "art"

[ 0.750000] 0x000000050000-0x0000007e0000 : "firmware"

[ 0.780000] libphy: ag71xx_mdio: probed

[ 0.780000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII

[ 1.340000] eth0: Found an AR7240/AR9330 built-in switch

[ 2.370000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII

[ 2.920000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]

[ 2.930000] TCP: cubic registered

[ 2.930000] NET: Registered protocol family 17

[ 2.940000] 8021q: 802.1Q VLAN Support v1.8

[ 2.950000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.

[ 2.960000] Freeing unused kernel memory: 212k freed

[ 6.370000] Registered led device: alfa:blue:lan

[ 6.370000] Registered led device: alfa:blue:usb

[ 6.370000] Registered led device: alfa:blue:wan

[ 6.370000] Registered led device: alfa:blue:wlan

[ 6.370000] Registered led device: alfa:blue:wps

[ 9.700000] jffs2: notice: (458) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 13 of xref (0 dead, 5 orphan) found.

[ 10.450000] SCSI subsystem initialized

[ 10.750000] usbcore: registered new interface driver usbfs

[ 10.760000] usbcore: registered new interface driver hub

[ 10.760000] usbcore: registered new device driver usb

[ 11.370000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 11.370000] ehci-platform ehci-platform: Generic Platform EHCI Controller

[ 11.380000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1

[ 11.420000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000

[ 11.440000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00

[ 11.440000] hub 1-0:1.0: USB hub found

[ 11.440000] hub 1-0:1.0: 1 port detected

[ 11.560000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 11.680000] uhci_hcd: USB Universal Host Controller Interface driver

[ 11.800000] Initializing USB Mass Storage driver...

[ 11.800000] usbcore: registered new interface driver usb-storage

[ 11.810000] USB Mass Storage support registered.

[ 11.910000] usb 1-1: new high-speed USB device number 2 using ehci-platform

[ 12.060000] scsi0 : usb-storage 1-1:1.0

[ 12.070000] scsi1 : usb-storage 1-1:1.1

[ 13.060000] scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 13.070000] scsi 1:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 13.080000] sd 1:0:0:0: [sda] Attached SCSI removable disk

[ 33.420000] Compat-drivers backport release: compat-drivers-2012-12-04

[ 33.420000] Backport based on wireless-testing.git master-2012-12-06

[ 33.430000] compat.git: wireless-testing.git

[ 33.460000] cfg80211: Calling CRDA to update world regulatory domain

[ 33.470000] cfg80211: World regulatory domain updated:

[ 33.470000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 33.480000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 33.490000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 33.500000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 33.500000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 33.510000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.010000] cfg80211: World regulatory domain updated:

[ 34.020000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 34.030000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.030000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 34.040000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)

[ 34.050000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 34.060000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)

[ 35.160000] usbcore: registered new interface driver rt73usb

[ 35.310000] usbcore: registered new interface driver rtl8187

[ 35.340000] ath: EEPROM regdomain: 0x833a

[ 35.340000] ath: EEPROM indicates we should expect a country code

[ 35.340000] ath: doing EEPROM country->regdmn map search

[ 35.340000] ath: country maps to regdmn code: 0x37

[ 35.340000] ath: Country alpha2 being used: GB

[ 35.340000] ath: Regpair used: 0x37

[ 35.350000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

[ 35.350000] Registered led device: ath9k-phy0

[ 35.350000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2

[ 35.370000] usbcore: registered new interface driver rt2800usb

[ 35.430000] cfg80211: Calling CRDA for country: GB

[ 35.430000] cfg80211: Regulatory domain changed to country: GB

[ 35.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

[ 35.450000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[ 35.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[ 35.460000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)

[ 35.470000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)

[ 35.510000] Button Hotplug driver version 0.4.1

[ 35.750000] RPC: Registered named UNIX socket transport module.

[ 35.750000] RPC: Registered udp transport module.

[ 35.760000] RPC: Registered tcp transport module.

[ 35.760000] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 36.110000] PPP generic driver version 2.4.2

[ 36.240000] tun: Universal TUN/TAP device driver, 1.6

[ 36.250000] tun: © 1999-2004 Max Krasnyansky

[ 36.540000] ip_tables: © 2000-2006 Netfilter Core Team

[ 36.780000] NET: Registered protocol family 24

[ 36.910000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)

[ 37.780000] usbcore: registered new interface driver ath9k_htc

[ 38.040000] usbcore: registered new interface driver usbserial

[ 38.050000] usbcore: registered new interface driver usbserial_generic

[ 38.060000] USB Serial support registered for generic

[ 38.060000] usbserial: USB Serial Driver core

[ 38.100000] usbcore: registered new interface driver cdc_ether

[ 38.220000] Error: Driver 'gpio-keys-polled' is already registered, aborting...

[ 38.340000] usbcore: registered new interface driver rndis_host

[ 38.470000] scsi 0:0:0:0: Attached scsi generic sg0 type 5

[ 38.470000] sd 1:0:0:0: Attached scsi generic sg1 type 0

[ 40.950000] sd 1:0:0:0: [sda] 3911680 512-byte logical blocks: (2.00 GB/1.86 GiB)

[ 40.970000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 40.980000] sda: sda1 sda2

[ 42.230000] usb 1-1: USB disconnect, device number 2

[ 42.250000] sd 1:0:0:0: [sda] Synchronizing SCSI cache

[ 42.250000] sd 1:0:0:0: [sda]

[ 42.250000] Result: hostbyte=0x01 driverbyte=0x00

[ 44.750000] device eth0 entered promiscuous mode

[ 46.750000] usb 1-1: new high-speed USB device number 3 using ehci-platform

[ 46.910000] scsi5 : usb-storage 1-1:1.3

[ 46.910000] scsi6 : usb-storage 1-1:1.4

[ 47.910000] scsi 5:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2

[ 47.920000] scsi 5:0:0:0: Attached scsi generic sg0 type 5

[ 47.930000] scsi 6:0:0:0: Direct-Access HUAWEI SD Storage 2.31 PQ: 0 ANSI: 2

[ 47.940000] sd 6:0:0:0: Attached scsi generic sg1 type 0

[ 47.950000] sd 6:0:0:0: [sda] Attached SCSI removable disk

[ 48.140000] device wlan0 entered promiscuous mode

[ 48.220000] br-lan: port 2(wlan0) entered forwarding state

[ 48.220000] br-lan: port 2(wlan0) entered forwarding state

[ 50.220000] br-lan: port 2(wlan0) entered forwarding state

[ 58.390000] device wlan0 left promiscuous mode

[ 58.390000] br-lan: port 2(wlan0) entered disabled state

[ 59.440000] device wlan0 entered promiscuous mode

[ 59.520000] br-lan: port 2(wlan0) entered forwarding state

[ 59.520000] br-lan: port 2(wlan0) entered forwarding state

[ 61.520000] br-lan: port 2(wlan0) entered forwarding state

[ 74.650000] USB Serial deregistering driver generic

[ 74.650000] usbcore: deregistering interface driver usbserial_generic

[ 74.660000] usbcore: deregistering interface driver usbserial

[ 77.690000] usbcore: registered new interface driver usbserial

[ 77.700000] usbcore: registered new interface driver usbserial_generic

[ 77.700000] USB Serial support registered for generic

[ 77.710000] usbserial_generic 1-1:1.0: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 77.720000] usbserial_generic 1-1:1.0: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 77.730000] usbserial_generic 1-1:1.0: generic converter detected

[ 77.740000] usb 1-1: generic converter now attached to ttyUSB0

[ 77.740000] usbserial_generic 1-1:1.1: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 77.750000] usbserial_generic 1-1:1.1: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 77.760000] usbserial_generic 1-1:1.1: generic converter detected

[ 77.770000] usb 1-1: generic converter now attached to ttyUSB1

[ 77.770000] usbserial_generic 1-1:1.2: The "generic" usb-serial driver is only for testing and one-off prototypes.

[ 77.780000] usbserial_generic 1-1:1.2: Tell linux-usb@vger.kernel.org to add your device to a proper driver.

[ 77.790000] usbserial_generic 1-1:1.2: generic converter detected

[ 77.800000] usb 1-1: generic converter now attached to ttyUSB2

[ 77.810000] usbserial: USB Serial Driver core

[ 90.010000] sd 6:0:0:0: [sda] 3911680 512-byte logical blocks: (2.00 GB/1.86 GiB)

[ 90.020000] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[ 90.040000] sda: sda1 sda2

[ 90.060000] EXT4-fs (sda1): recovery complete

[ 90.060000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)

[ 131.450000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)@qualcomm.com>

@qualcomm.com>

Execute: ls /dev/sd*

dev/sda

/dev/sda1

/dev/sda2

Edited by d1000
Link to comment
Share on other sites
  • 1 month later...
d1000 Newbie

d1000

Posted
  • Author
Posted

Hi webdirector,

Will post my fstab no prob asap. But in my case, I could mount one of the two partitions and when try to use disappeared again. Still waiting for a working usb hub to identify if was a power issue like most of this problem.

Will post it today or tomorrow, sorry for the delay.

Cheers,

D1000

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...