JOHNDarc0de Posted December 29, 2012 Share Posted December 29, 2012 I Know this is a stupid question but i have no option i successfully copied the helloword in my sd card then i inserted the sd in my rubber ducky and i inserted the ducky in my usb port and i got the desired out put, but now i am unable to remove the sd card , the ducky seems to be very delicate so i don't want to risk anything, can some one instruct me the correct way on how to remove the sd card from the ducky Quote Link to comment Share on other sites More sharing options...
no42 Posted December 29, 2012 Share Posted December 29, 2012 Its always a little stiff at first... try to use your nail (any finger or thumb) and apply outward pressure on the small lip of the exposed part of the mini-sdcard. Eventually, it will come free... you may want to repeatedly insert remove the card, to break it in. After a few attempts you'll have no stiffness issues. Quote Link to comment Share on other sites More sharing options...
zac115 Posted January 7, 2013 Share Posted January 7, 2013 bring this back up how do you take out the sd card on the green board it came wih it all ready in???? Quote Link to comment Share on other sites More sharing options...
PineDominator Posted January 7, 2013 Share Posted January 7, 2013 (edited) bring this back up how do you take out the sd card on the green board it came wih it all ready in???? The green duck I have is the first revision, u have to slide the piece of metal holding in the sd card toward the USB end, then it should flap open. But if it's like my red one (revision 2) then u just slide the card out with a bit of force Edited January 7, 2013 by petertfm Quote Link to comment Share on other sites More sharing options...
zac115 Posted January 7, 2013 Share Posted January 7, 2013 The green duck I have is the first revision, u have to slide the piece of metal holding in the sd card toward the USB end, then it should flap open. But if it's like my red one (revision 2) then u just slide the card out with a bit of force i am not really sure what revision i have a green broad but the part that holds in the sd is fixed to there are no hinges and if it is spring loaded it is broken when i got Quote Link to comment Share on other sites More sharing options...
no42 Posted January 7, 2013 Share Posted January 7, 2013 you normally have a small RX, where X is a number in the corner of the board (usually appears on both sides) I believe the color versions are: Green = R1 Red = R2 White =R3 So you probably have one with the sliding metal tab Quote Link to comment Share on other sites More sharing options...
zac115 Posted January 7, 2013 Share Posted January 7, 2013 you normally have a small RX, where X is a number in the corner of the board (usually appears on both sides)I believe the color versions are: Green = R1 Red = R2 White =R3 So you probably have one with the sliding metal tab ya it says r1 but mine is not a sliding tab i have looked for the hing but there is none and i tried pulling it out but the sd will not budge and i called and emailed hak5 but there has been no answer are they at some convention right now Quote Link to comment Share on other sites More sharing options...
Solution ashbreeze96 Posted January 9, 2013 Solution Share Posted January 9, 2013 sounds like you have the same version as me. it is green with R1 but the card holder is completely soldered down. i took a pair of fine tipped needle nose pliers and gently pulled til it came out the first time. now after being used a bit, it comes out with a push from a fingernail Quote Link to comment Share on other sites More sharing options...
zac115 Posted January 9, 2013 Share Posted January 9, 2013 sounds like you have the same version as me. it is green with R1 but the card holder is completely soldered down. i took a pair of fine tipped needle nose pliers and gently pulled til it came out the first time. now after being used a bit, it comes out with a push from a fingernail nice thank for the tip Quote Link to comment Share on other sites More sharing options...
PineDominator Posted January 9, 2013 Share Posted January 9, 2013 sounds like you have the same version as me. it is green with R1 but the card holder is completely soldered down. i took a pair of fine tipped needle nose pliers and gently pulled til it came out the first time. now after being used a bit, it comes out with a push from a fingernail I used mine so much it almost falls out. Quote Link to comment Share on other sites More sharing options...
Bryguy Posted April 21 Share Posted April 21 I think i have the r1 but it wont come out because there is a sautr blocking the sd card from being removed Quote Link to comment Share on other sites More sharing options...
dark_pyrro Posted April 21 Share Posted April 21 28 minutes ago, Bryguy said: there is a sautr blocking the sd card I have no idea what a "sautr" is, but you probably have a gen2 Ducky if you just got it and there shouldn't be anything blocking the Micro SD card slot on the gen1 Ducky in the way that the USB-C connector mounting blocks the Micro SD card slot on the gen2. Bringing an 11 year old thread to life isn't most likely relevant in this case either. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.