Jump to content

Trouble With Wlan1


akraut
 Share

Recommended Posts

Hey folks,

I'm trying to use the USB wireless card that came in the Pro pack to relay wifi using the directions at this post: http://forums.hak5.o...l__ wifi relay

However, I keep getting errors about wlan1 being a non-existant device occasionally. Looking at dmesg, I see this repeated:


[ 307.960000] usb 1-1: new high-speed USB device number 22 using ehci-platform
[ 313.140000] usb 1-1: ath9k_htc: Firmware htc_9271.fw requested
[ 313.530000] usb 1-1: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
[ 313.770000] ath9k_htc 1-1:1.0: ath9k_htc: HTC initialized with 33 credits
[ 313.970000] ath9k_htc 1-1:1.0: ath9k_htc: FW Version: 1.3
[ 313.970000] ath: EEPROM regdomain: 0x833a
[ 313.970000] ath: EEPROM indicates we should expect a country code
[ 313.970000] ath: doing EEPROM country->regdmn map search
[ 313.970000] ath: country maps to regdmn code: 0x37
[ 313.970000] ath: Country alpha2 being used: GB
[ 313.970000] ath: Regpair used: 0x37
[ 313.970000] ieee80211 phy20: Atheros AR9271 Rev:1
[ 313.980000] Registered led device: ath9k_htc-phy20
[ 319.300000] usb 1-1: USB disconnect, device number 22
[ 319.400000] ath: phy20: RX failed to go idle in 10 ms RXSM=0x81872a80
[ 319.420000] ath: phy20: DMA failed to stop in 10 ms AR_CR=0x81873cbc AR_DIAG_SW=0x81873cbc DMADBG_7=0x81873cbc
[ 319.440000] ath: phy20: DMA failed to stop in 10 ms AR_CR=0x81873cbc AR_DIAG_SW=0x81873cbc DMADBG_7=0x81873cbc
[ 319.560000] ath: phy20: RX failed to go idle in 10 ms RXSM=0x1
[ 319.570000] ath: phy20: DMA failed to stop in 10 ms AR_CR=0x81873cbc AR_DIAG_SW=0x81873cbc DMADBG_7=0x81873cbc
[ 319.690000] ath: phy20: RX failed to go idle in 10 ms RXSM=0x1
[ 319.700000] ath: phy20: DMA failed to stop in 10 ms AR_CR=0x81873cbc AR_DIAG_SW=0x81873cbc DMADBG_7=0x81873cbc
[ 319.720000] usb 1-1: ath9k_htc: USB layer deinitialized
[/CODE]

The phy## increments each time as well as the USB device number.

I'm using an MK4 running 2.7.0. It's powered via the included wall-wart. Besides the /etc/wpa_supplicant.conf and ~/wireless_connect.sh the configuration is otherwise factory defaults. Any ideas?

Link to comment
Share on other sites

hmm, not enough amperage maybe, most people have to use a powered hub when using stuff that requires lots of power.

question are you getting the error after a reboot or does the card stop working and then you run the script again. I find with wifi cards and usb hub I have to unplug then replug power to get it to work correctly

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...