Tataboutlamin Posted October 16, 2012 Share Posted October 16, 2012 I just bricked my pineapple mark IV. I made a firmware flashing and my pc Rebooted in the sametime..... now I can't access my router pineappe when i try, i just reach the "redirect.php" in loop :( is there a way to fix it? Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted October 16, 2012 Share Posted October 16, 2012 Try http://172.16.42.1:1471 Please read my thread on how to ask questions, also read the change logs. Quote Link to comment Share on other sites More sharing options...
Tataboutlamin Posted October 16, 2012 Author Share Posted October 16, 2012 ok Thanks... I'll be home at 9pm and try this! Quote Link to comment Share on other sites More sharing options...
PineDominator Posted October 17, 2012 Share Posted October 17, 2012 what version were you upgrading from? because if it was one that required md5 checking this should not happen unless the pineapple had power loss Quote Link to comment Share on other sites More sharing options...
zettaquark Posted October 17, 2012 Share Posted October 17, 2012 OT- sorry to bust in here: @Petertfm: Can't hit you up on pm... ?? Z** Quote Link to comment Share on other sites More sharing options...
Tataboutlamin Posted October 17, 2012 Author Share Posted October 17, 2012 Try http://172.16.42.1:1471 Please read my thread on how to ask questions, also read the change logs. Hey you were right, I can now access my pineapple wifi, but it's the ONLY way I can!!! It seems that the firmware is updated but I'm not to sure about that, 'cause even if I launch the script to start it again, it cannot start properly. So what can I do to fix all of this? I tried the option "reset" in the ADVANCED tab but it didn't work. Any hints? And thanks again by the way :) Quote Link to comment Share on other sites More sharing options...
Tataboutlamin Posted October 17, 2012 Author Share Posted October 17, 2012 what version were you upgrading from? because if it was one that required md5 checking this should not happen unless the pineapple had power loss I think it was 2.4.1 to 2.7.... but I did unplug my router after that :( I didn't know that specification before you told me! Quote Link to comment Share on other sites More sharing options...
zettaquark Posted October 17, 2012 Share Posted October 17, 2012 once you get to the UI can you then: 1. stop all modules 2. go to update and attempt to check for upgrades 3. choose re-flash to 2.7.0 4. use a ups if you have power issues.... reflash first.... hopefully that will get you back up and running. 5. I would recommend using the mkIV setup script found by topic unde3r jasenger... I think petertfm is the originator and author?? Good luck ;) Z** Quote Link to comment Share on other sites More sharing options...
Tataboutlamin Posted October 17, 2012 Author Share Posted October 17, 2012 once you get to the UI can you then: 1. stop all modules 2. go to update and attempt to check for upgrades 3. choose re-flash to 2.7.0 4. use a ups if you have power issues.... reflash first.... hopefully that will get you back up and running. 5. I would recommend using the mkIV setup script found by topic unde3r jasenger... I think petertfm is the originator and author?? Good luck ;) Z** Ok so first of all, the ONLY way that I can access my pineapple router is by this address that someone gave me on this post : http://172.16.42.1:1471 I can't access the router by typing http://172.16.42.1 nor http://172.16.42.1/pineapple . When I do by http://172.16.42.1/pineapple it's an infinite loop of redirect.php, it never stops. I did what you told me until number 4 (not sur to understand #5) and the fruits go on and on (to show me that it's flashing). It says that "The pineapple will reboot once the upgrade is complete and this page will refresh automatically!" but it's been 30 minutes that it's flashing lol. Any opinions? Should I try to downgrade? The only way to access my router is being wired and using http://172.16.42.1:1471 Thanks again guys! Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted October 17, 2012 Share Posted October 17, 2012 Ok so first of all, the ONLY way that I can access my pineapple router is by this address that someone gave me on this post : http://172.16.42.1:1471 I can't access the router by typing http://172.16.42.1 nor http://172.16.42.1/pineapple . When I do by http://172.16.42.1/pineapple it's an infinite loop of redirect.php, it never stops. That is correct, please read changelog http://cloud.wifipin...dex.php?changes Specifically, 2.6.4 changes... I did what you told me until number 4 (not sur to understand #5) and the fruits go on and on (to show me that it's flashing). It says that "The pineapple will reboot once the upgrade is complete and this page will refresh automatically!" but it's been 30 minutes that it's flashing lol. Any opinions? Should I try to downgrade? The only way to access my router is being wired and using http://172.16.42.1:1471 Thanks again guys! If the WPS light isn't flashing, try to close and re-open browser, http://172.16.42.1:1471 Quote Link to comment Share on other sites More sharing options...
Tataboutlamin Posted October 17, 2012 Author Share Posted October 17, 2012 That is correct, please read changelog http://cloud.wifipin...dex.php?changes Specifically, 2.6.4 changes... If the WPS light isn't flashing, try to close and re-open browser, http://172.16.42.1:1471 OHHHHHH I see :) Txs a Lot! What about the script we download to "install" and launch the rooter? It redirect to the wrong page after installing preferences... normal? Do all the preferences that we set with the script working? Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted October 17, 2012 Share Posted October 17, 2012 OHHHHHH I see :) Txs a Lot! What about the script we download to "install" and launch the rooter? It redirect to the wrong page after installing preferences... normal? Do all the preferences that we set with the script working? I'm not sure what those 3 questions are asking about, please be more specific. Are you talking about the wp4.sh? Quote Link to comment Share on other sites More sharing options...
Tataboutlamin Posted October 17, 2012 Author Share Posted October 17, 2012 I'm not sure what those 3 questions are asking about, please be more specific. Are you talking about the wp4.sh? Sorry for my english i speak french... yeah im talking about the file wp4.sh.... seems like when i use the command "wget wifipineapple.com/wp4.sh; chmod +x wp4.sh; ./wp4.sh; firefox http://172.16.42.1/pineapple &" everything is going well, except that in the end of everything, it tries to load "http://172.16.42.1/pineapple" as it was.... I guess I don't bother with that and typing the new IP address with new port is enough? Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted October 17, 2012 Share Posted October 17, 2012 Sorry for my english i speak french... yeah im talking about the file wp4.sh.... seems like when i use the command "wget wifipineapple.com/wp4.sh; chmod +x wp4.sh; ./wp4.sh; firefox http://172.16.42.1/pineapple &" everything is going well, except that in the end of everything, it tries to load "http://172.16.42.1/pineapple" as it was.... I guess I don't bother with that and typing the new IP address with new port is enough? The script has not been updated, It says to use the old GUI path. Use the one that ends in 1471 for the port. You will also need to run wp4.sh as sudo or as root. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.