Geomancer626 Posted March 14, 2012 Share Posted March 14, 2012 After issuing the command (reaver -i mon.wlan0 -b <bssid> -c <channel of WAP> -vv) reaver hangs on waiting for a beacon from the AP. This is my own AP and I have successfully tested Reaver against it in the past, any suggestions? My mark IV is running the 1.0.2 firmware. Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted March 14, 2012 Share Posted March 14, 2012 Sounds like the monitor mode channel is incorrect. Try iwconfig and change the channel there before running reaver. Quote Link to comment Share on other sites More sharing options...
Geomancer626 Posted March 14, 2012 Author Share Posted March 14, 2012 No change to the resulting output I'm afraid. Quote Link to comment Share on other sites More sharing options...
Geomancer626 Posted March 14, 2012 Author Share Posted March 14, 2012 Though for the sake of thorough troubleshooting, the interface would not allow me to adjust the channel without first issuing ifconfig mon.wlan0 down and ifconfig wlan0 down. Quote Link to comment Share on other sites More sharing options...
Mr-Protocol Posted March 14, 2012 Share Posted March 14, 2012 Though for the sake of thorough troubleshooting, the interface would not allow me to adjust the channel without first issuing ifconfig mon.wlan0 down and ifconfig wlan0 down. That is a normal result. take interface down, change, then back up. Quote Link to comment Share on other sites More sharing options...
Darren Shady Posted March 14, 2012 Share Posted March 14, 2012 I have the same issue. Reaver doesn't work on 1.02; have BT5 running it against same targets and works fine. Quote Link to comment Share on other sites More sharing options...
iamk3 Posted March 14, 2012 Share Posted March 14, 2012 Please search before posting. This is a known problem and there is already a thread on it. Quote Link to comment Share on other sites More sharing options...
Geomancer626 Posted March 15, 2012 Author Share Posted March 15, 2012 Perhaps you could point to that specific thread? My searches didn't turn up ANYTHING regarding this particular issue. Quote Link to comment Share on other sites More sharing options...
iamk3 Posted March 15, 2012 Share Posted March 15, 2012 (edited) Geomancer626: http://forums.hak5.org/index.php?showtopic=25691 Afaik, no one has been able to get it to function correctly on the Pineapple. You can SSH into the device and issue ifconfig mon.wlan0 down ifconfig wlan0 down airmon-ng stop mon.wlan0 (or) airmon-ng stop wlan0 then ifconfig start wlan0 At this point, it should start an interface called mon0 then try reaver -i mon0 -b xx:xx:xx:xx:xx:xx -vv Good Luck! :) (EDIT: After doing a little Google-fu, this seems like it might be a problem with OpenWRT) Edited March 15, 2012 by iamk3 Quote Link to comment Share on other sites More sharing options...
Jmanuel Posted April 7, 2012 Share Posted April 7, 2012 Geomancer626: http://forums.hak5.org/index.php?showtopic=25691 Afaik, no one has been able to get it to function correctly on the Pineapple. You can SSH into the device and issue ifconfig mon.wlan0 down ifconfig wlan0 down airmon-ng stop mon.wlan0 (or) airmon-ng stop wlan0 then ifconfig start wlan0 At this point, it should start an interface called mon0 then try reaver -i mon0 -b xx:xx:xx:xx:xx:xx -vv Good Luck! :) (EDIT: After doing a little Google-fu, this seems like it might be a problem with OpenWRT) I followed these steps but it only goes in circles between ch1 to ch14 Quote Link to comment Share on other sites More sharing options...
barry99705 Posted April 8, 2012 Share Posted April 8, 2012 I followed these steps but it only goes in circles between ch1 to ch14 Well that last line in the post you quoted says it's a problem with openwrt. Reaver doesn't work yet. Quote Link to comment Share on other sites More sharing options...
gamephreaker Posted April 29, 2012 Share Posted April 29, 2012 I can't seam to get wash command working I am trying to scan it works fine in backtrack but for some reason not when I am ssh-ed into the pineapple. Quote Link to comment Share on other sites More sharing options...
barry99705 Posted April 29, 2012 Share Posted April 29, 2012 It's still not functional in openwrt. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.