Jump to content

Search the Community

Showing results for tags 'wp6.sh'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 6 results

  1. So, it's taken me about a week (off and on) since receiving my Nano to get ICS working. I can imagine if you're reading this you, like myself were aimlessly trying suggestions people have listed in the forums to no avail. It seems, like the wp6.sh script shown in the guides is broke. I'm no expert on IPtables but, alas there's a pull request / issue on the github repository for the script. Here's a link to the PR conversation. https://github.com/hak5darren/wp6/pull/4?_pjax=%23js-repo-pjax-container I've used the commit approved by H4xl0r on May 27, 2018. I dont know how this fix has
  2. Hi, I am a new user to the Tetra. I was able to set it up one time and never again. I did some searching for WP6 issues and none seemed to match my specific error/problem, so I am hoping someone here can help. I downloaded the WP6 and ran the Guided setup connected the tetra and saved the settings. I then selected Connect using saved settings and get several errors: ./wp6.sh: line 281: echo: write error: Invalid argument iptables/1.8.2 Failed to initialize nft: Protocol not supported iptables/1.8.2 Failed to initialize nft: Protocol not supported iptables/1.8.2 Failed to init
  3. Hi there, I'm trying to configure internet on my WIFI Pineapple Nano by using wp6.sh on my Ubuntu. Once reset (holding 10 secs the reset button), on my Ubuntu I downloaded the wp6.sh script and followed the steps explained here: https://docs.hak5.org/hc/en-us/articles/360010471454-Internet-connection-sharing-over-Ethernet-in-Linux ...but unfortunately it never worked as expected. The Firmware version of my WIFI Pineapple nano is 1.0.5 and obviously I can not upgrade from the Web UI. On my Ubuntu: $ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Ma
  4. I am new to the wifi pineapple and while setting it up, i found i could not share the internet. I am using the wp6.sh script at v6.5. I want to share my eth0 to the wifi pineapple either through eth1 (pineapple USB) or wlan0 (connected to management AP) any help would be appreciated, thanks.
  5. OS version is Parrot OS 3.9 (Intruder). Confirmed that ufw is not running. Confirmed that my internet gateway = 192.168.1.1 ┌─[eric@parrot]─[~] └──╼ $ip route | grep default default via 192.168.1.1 dev wlan0 proto static metric 600 Confirmed that internal wifi is wlan0. ┌─[eric@parrot]─[~] └──╼ $ifconfig eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether 54:a0:50:4d:89:57 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dr
  6. I'm currently running Ubuntu 16 and was trying to setup the wp6.sh I took the following steps: wget wifipinapple.com/wp6.sh chmod +x wp6.sh sudo ./wp6.sh I get the following error: .wp6.sh 1: ./wp6.sh Syntax error: redirection unexpected I also tried sudo bash wp6.sh Any thoughts or anyone else have this issue? Thanks
×
×
  • Create New...