Jump to content

Search the Community

Showing results for tags 'uart'.

  • Search By Tags

    Type tags separated by commas.

  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End

Last Updated

  • Start

    End

Filter by number of...

Joined

  • Start

    End

Group

AIM

MSN

Website URL

ICQ

Yahoo

Jabber

Skype

Location

Interests

Enter a five letter word.

Found 4 results

  1. Buff_r
    i was wondering if these are possible serial headers. I'm trying to hopefully get a shell from this. and how would i communicate with these do i use any TTL adapter are does it have to be specific. also what it an easy way to identify the headers TX,RX,VCC,GND...? I'm a beginner so please give me some tips. Images: Device: NetComm NB6Plus4Wn I'm a beginner at this so please give me some tips too. :)
  2. PierogiPowered
    Good evening. I've been tinkering with a mark IV Wifi Pineapple. I recently went to upgrade and the upgrade failed. I waited a half hour and couldn't do anything. I tried power cycling it and found that it was bricked. https://wifipineapple.com/?flashing I went to follow the instructions on the main wifipineapple.com site at the link above. That specific page didn't mention that you shouldn't connect VCC to VDD when trying to serial flash it. I made the connection. When I powered the device up, I had console. Then the device went entirely dead. Anyone with hardware experience know what to do? Is there a fuse or resistor in the path that can be replaced with some soldering or did I fry a chip? I'm hoping I can salvage this device.
  3. ktulu
    [sOLVED!] For those of you having the same problem as me, I fixed it by using the power cable that it was shipped with, rather than the USB power cable. Because I am in the UK, I had to use a shaver to mains adapter. Thanks everyone. Hey guys, me and a friend got our hands on the AP121U via ebay and were hoping to flash them with the Jasager firmware. We followed the guide to the letter and used UART cables to flash the factory binaries onto the devices. However, they enter into a boot loop after resetting them. I can hit 'f' and return to drop into failsafe mode, where we're presented with the following prompt: root@(none):/# I've tried starting dropbear to scp over the Jasager files to /tmp/, but I can't even establish a connection (yeah, I'm using the PoE port). Any ideas would be much appreciated. P.S. I thought it could have been a dodgy AP121U, but my friend's does EXACTLY the same thing as mine.
  4. Sah5die
    Hey Everybody, is there anyway to change the Serial Speed on the MK IV ? I tried stty, mgetty and setserial and none of them worked. (with /dev/ttyS01) Need to use the serial port over a wireless(433Mhz) link that runs at max 19200 Baud, so default speed 115200 is way to fast ;) Any Suggestions? Cheers Max
×
×
  • Create New...