Search the Community

Hi, I'm selling my WiFi pineapple Tetra New not used at all only opened the box with its full field guide! Going for 149£. shipping fee may apply for worldwide shipping. Selling it because I do not need it and have never used it. Can send full pictures

I have no idea why, but after successful configuration using the USB y-cable I cannot connect to the management IP address. I can connect to the network fine, but the 172.16.42.1:1471 IP gives me a "refused to connect" error. I've done a factory reset twice and it's the same result once I remove it from the connection to my laptop. What's the point in having this thing if I can't use it without it being connected to my laptop. Makes no real sense to me. Anyone have a real fix for this? I'm about 24 hours from sending it back...

Tried and tried. USB tethering is on. USB connection set to tether with phone (Android) in control. Would not allow tethering with device in control. Nothing. Pineapple blue light on and flashing, flashing, flashing. Tried reset button. Tried incense and prayers. Nothing helps. 'Sup?

I have a new Pineapple Tetra (MK5.8) with a specific reset problem. It can Recon just fine -- days without any issue, detecting all the right things. But, the moment I enable any transmitters in PineAP, it reboots. Here are the easiest steps to crash it: Factory Reset on Firmware 2.5.4, do basic intro/configuration Recon w/ Start PineAP for 30 seconds Pick a client MAC Deauth BOOM, reboot and back to login Or more typically: Factory Reset "Get Started", set basic configuration screen Recon w/ Start PineAP Pick an SSID from Recon Scan Results ("PineAP Pool: Add SSID" and "PineAP Filter: Add SSID") Confirm that Filters show Clients Deny:None, SSID: Allow corpAP Switch to PineAP tab, confirm PineAP Daemon: Enabled PineAP checkbox Log PineAP Events, Save PineAP checkbox Client Connect/Disconnect Notifications, Save PineAP checkbox: Broadcast SSID Pool, Save and BOOM, reboots immediately on Save Enabling Beacon Response, or Associations also crashes it. Even a simple Deauth from Recon crashes it. I have tried: Dozens of Factory Resets Minimalist configuration just to get it running (no special options/settings) Get Started, set basic configuration Firmware recovery to 2.4.1 Firmware upgrade to 2.5.4 This really feels like a power-related problem -- as if it resets when the second radio tries to Transmit. Is there any other test I can do to confirm it? Power supplies I have tried: The included 12v 2A AC Adapter (Intertek) (preferred by Hak5 Forum users the world over) The USB Y-Cable with two supplies Two lab-grade bench power supplies set to 5.25V DC feeding each of the two MicroUSB ports on the Tetra Two USB Batteries A lab power supply at 12.0V with up to 3A of current. 13v power supply to see if connector/cable loss is an issue All THREE power supplies at once (12v 2A, 5v 2.5A, 5v 2.5A) I really thought I'd find a power solution that runs it, but no. I was able to see more the expected reboots when running under-powered single-USB supplies, but that's well-documented. The highest consumption I've seen on 12v is only 0.7 Amps, far from the "24W" I was expecting. One possibility is that a Tx power amplifier is messed up and surging huge current on any transmission from PineAP. Does PineAP use a different transmitter or amp than anything else? It could be a more general fault in the (regulated) power distribution in the Tetra, since it behaves the same on 5v or 12v supply. I'm open to any ideas to debug this.. it's just a passive monitor otherwise. Thanks!

I just got my pineapple yesterday and I managed to update the firmware. It took about two hours because of wifi dropping from laptop.or pineapple. When I connect the wifi to my laptop then connect the tetra pineapple, the wifi disconnects from my laptop. The pineapple is still connected, then I reconnect the wifi and then the pineapple gets disconnected. Am I doing something wrong or is there a glitch with the pineapple? Thank in advance.