Jump to content

Search the Community

Showing results for tags 'red led'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 5 results

  1. I just flashed my rubber ducky with the ducky flasher and got the message that my rubber ducky had been flashed with the twin duck original firmware. Now I just get a solid red led every time I insert the ducky into my computer. I have even tried with different sd cards and payloads. I am not sure how to fix this problem. Your help would be appreciated.
  2. thomas@

    New user

    Good day guys, New user to bash bunny, However old user had one of first batches of rubber ducky. With that said got my bunny in the mail yesterday, got a chance to plug it in today. Mounted fine on my OSX After unmounting and putting it away for a bit, I plugged it back in to the same machine again. And it seems it is not mounting and goes to a solid RED led. I've read this is recover mode I left it for an hour and nothing happens. It is in arming mode, Selecting closest to USB side. Lights up green blinks a few times then goes solid red. Any thoughts on how to fix this. Never even got a chance to set anything up or get anything going. I plugged it into a windows 10 machine at work and did the same thing. thanks
  3. Hi, I have a couple of 64MB micro SD card (some have TransFlash written on them) but my ducky does not seem to recognise them, all I get is a red LED on the ducky. Is there a minimum spec of microSD card or a specific format for low capacity SD cards? At the moment they are formatted to FAT with an Allocation unit size 2048 bytes. I know it’s not the payload as have put it on the microSD the duck came with (128MB I think) and a 16GB and both work fine.
  4. Over the past ~48 hours I've been trying to get my pineapple to work. I seem to be having a very unusual (read: undocumented) error with this device, with the symptoms below: - Firstly, it tends to boot into what I have termed 'derp mode' where it gets stuck in a boot loop. This is usually characterized by solid green and faint-ish blue and VERY faint red LEDs. - Secondly, I have managed to get the device to boot/operate for a limited time (more detail later). - I noticed that it would enter derp mode if I rebooted it (i.e. power cycled) immediately. If I let it wait for ~5-10 minutes, it would actually run through the boot cycle. Now for a brief description of Derp Mode: - The device will not enter any form of boot cycle, just the immediate aformentioned LEDs. To me this indicates that the kernel isn't even getting hooked by the bootloader, if the bootloader (I assume RedBoot) is even getting loaded. - Derp mode will hold indefinitely, and has done so for several hours. During this time, it will not change state in any way. - As previously mentioned, rebooting immediately will not alleviate this problem in any way. Last night, the problem was somewhat mitigated by keeping the device cool (it's not getting especially warm). This allowed a successful unbricking and boot. The device works perfectly when cooled, however, this is not a practical use for it. As I am sure many people will offer the obligatory 'RTFM' comment, here is a concise list of common fixed that have been applied: - Standard factory reset - Standard (web facing) un-bricking (reflashing) - Power supply testing - Serial console debugging In summary: The device does work when exposed to colder temperatures; All normal operations function well in this state. To me, this indicates a potential manufacturing fault within the hardware. I will be contacting HakShop shortly regarding this, however, I am curious if anybody else has had a similar issue. I would really like to take the device apart and have a look at it, and maybe test it in the lab to try and get to the root of the problem, however, I do not wish to do so before getting in contact with the HakShop staff. Let me know what you think.
  5. Good Morning, Afternoon or Evening, About 2-3 weeks ago I received my Ducky. I unpacked everything. I took the following steps / got the following results: 1) Formatted the stock 256MB MicroSD card as FAT. 2) Inserted with no code in Duck. 3) Solid red LED comes on immediately. 4) Removed MicroSD, put in carrier, copied "Hello World!" to card. Reinserted in Duck, 5) Still solid red LED. 6) Tried every other available format - FAT32, exFAT(?), NTFS, no go. 7) Tried a name brand (Sans Disk) 8GB MicroSD. 8) Repeated steps 1-4, same result. I get the red LED with or without a card inserted, formatted in any format, with or without the stock "Hello World" script. I contacted Hak5 shop, they replied with what seemed to be "sympathetic boilerplate" - extending regrets for my issues but advising me they don't do tech support and referred me to this forum. Soooo, here I am! B) Does anyone have any ideas, suggestions, etc.? Or should I call it quits and return the Duck to Hak5 for replacement? :( Cheers, --P P.S.: I should probably add: I'm running Windows 7 Ultimate 64 bit, if that matters (I suspect it doesn't really, but if I knew what the prolem & fix were, you wouldn't be reading this! ;-P )
×
×
  • Create New...