Search the Community
Showing results for tags 'mark 7'.
Hello! We're happy to announce the release of 1.0.1 for the WiFi Pineapple Mark VII. Based on your invaluable feedback (especially the Beta channel testers, thank you!) - numerous improvements to PineAP, Recon, Settings and more have been made. Be sure to check out the changes below and grab the new release by giving your WiFi Pineapple Mark VII an internet connection and going to "Settings > Check for Updates". Changelog: Setup Improve screen real-estate on smaller mobile screens. Button delay now says 4 seconds, to match the recovery wizard. PineAP Dramatically reduce the CPU percentage used by PineAP during idle and during scans. Logging options can now be persistently stored in the browser. Tweak the appearance of the logging options side bar. A spinner now shows when PineAP is saving the users configuration. Fixed an issue where the PineAP Source MAC option was not saving. Fixed an issue where the PineAP Autostart functionality would not work correctly. Fixed an issue where the PineAP Autostart toggle would not report a correct status. Fixed a rare issue where PineAP would not start after being disabled. Improved the settings save time. Recon Recon Table Columns can now be toggled to show or hide. Added an OUI column to the Recon Table. Scan duration choice is now remembered when you navigate away from Recon. Fixed an issue introduced in Beta 2, where Recon would sometimes show an error if PineAP was not running. Result cards are now clickable, instead of using a button to open the bigger view. Result cards for Clients now render the timestamp in human-readable format. Modules Fixed an issue introduced in Beta 3 where modules would not start due to a missing SSL dependency. Modules can now use PNG icons as well as SVGs. Settings Add censorship mode. Keyboard shortcuts can now be enabled or disabled from the Advanced Settings tab. Software Update will now accurately display when the selected update channel is closed. Small text changes to Software Update. Fixed an issue where Client Mode may not report an error correctly. Improve reliability of Client Mode. Client Mode settings are now saved automatically, and will re-connect on boot automatically. Add an option to reinstall the current firmware if no update is found. Greatly improve Network page for smaller mobile screens. Greatly improve Settings page for smaller mobile screens. Cloud C2 Improved the reliability of Recon scans. Misc Fix an issue where the Web Terminal would not connect when connected to the WiFi Pineapple via WAN. Updated the Python library for WiFi Pineapple Mark 7 modules. Fixed a rare issue where the internet connectivity check would fail despite having internet. Add support for USB Ethernet adapters using the ASIX AX88179 chipset. Add support for USB Ethernet adapters using the Realtek RTL8152 chipset. As always, feedback is greatly appreciated, and you're encouraged to join the community to discuss!
HI, A couple of weeks ago I wanted to update my wifi Pineapple to the latest software however, it seemed to never end.. I was busy so I left it aside for a later recovery. Today I decided to give it some time. Everything seems to be fine to the point where I upload the recovery bin file (checksum matching). From that point onwards it seems like nothing is happening. The led is red solid. From time to time I see the eth1 interface (which is the pineapple) is assigned an IPv6 address. Then it's unassigned then assigned again. There are even some rx and tx packets. Is there any other step to get this finally sorted? I had been in that state for a long time now.. much more longer that the 5-10 mins it should have taken... Thanks for helping ! -------------------------------------------- SOLVED After i posted this, I unplugged it, pressed the reset button, plugged it back in and released the reset button after the red led flashed for the third time and refreshed the the recovery page. The led turned purple and the page then said the updating was in progress and it was up and running again a couple of minutes later. Not sure why it had this behavior as the recovery guide says not to unplug it. Anyways, good new 😌
Hi! We've just pushed Beta 1 for 1.0.2 to the WiFi Pineapple BETA Channel. This update features some small bug fixes and UX improvements since 1.0.1. If you'd like to try the upcoming release, updating is easily done by following the above guide. Change Log: Recon Fixed an issue where the dBi column would not sort. Show a message if all table columns are disabled. Fixed an issue where results would not update when navigating back to a running scan. Campaigns Added the functionality to delete campaign reports. Misc Fix an issue with ICS routing introduced in 1.0.1. Cloud C2 Improvements to Cloud C2 functionality. Add the ability to manage Client Mode whilst in C2 Mode. Upcoming Changes: Improved support for WPA3 and WPA2/3 Mixed Client Mode Have a suggestion? Let us know! We're constantly looking for feedback, especially during the public beta programs. If you're interested in joining the discussion, be sure to check out the community page and say hello! Thanks, Foxtrot