Jump to content

Search the Community

Showing results for tags 'mac os x'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 3 results

  1. Hello Everyone, You may have seen my last post on the iMessage Taker. It was unstable and had timing issues. Well today I am here to rectify the situation. I have vastly improved the script to allow for much quicker operation and reliability. Basically the ducky script is quite small and edits a "scpt" that it downloads from a Repo of mine. This script does require internet connection. In order to change the script to send the Messages to your email all you need to do is change "YOUREMAIL" to your preferred email. It will then take iMessages from the computer and send them to you. Short and Sweet! Enjoy! -wiredbrother https://pastebin.com/3fgET9zU P.S Would love everyone's though on this.
  2. I received a wifi pineapple nano as a Christmas gift and have yet to get any use out of it. I continually have issues restoring the firmware, IP address drops, can't access internet on host, etc. So... I finally got the firmware to load, 2.0.2, and can access the web panel on 172.16.42.1. However I cannot load modules or wifi bullets, nor access the internet from my computer. I did install wp6,sh appropriately. Here is my setup: Mac OS X running VMWare Fusion I have internet on my Mac, but not on Kali or pineapple. Kali Linux Guest on Bridge mode eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.163 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fe80::9214:9b83:34f6:e4fe prefixlen 64 scopeid 0x20<link> ether 00:50:56:2c:e8:c4 txqueuelen 1000 (Ethernet) RX packets 33831 bytes 38502566 (36.7 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 15159 bytes 1867459 (1.7 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 172.16.42.111 netmask 255.255.255.0 broadcast 172.16.42.255 inet6 fe80::1ef:d781:91d2:dc5 prefixlen 64 scopeid 0x20<link> ether 00:c0:ca:90:dc:7f txqueuelen 1000 (Ethernet) RX packets 4972 bytes 3106425 (2.9 MiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 4745 bytes 871859 (851.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 USB tethered to nano Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.16.42.0 * 255.255.255.0 U 0 0 0 br-lan 192.168.1.0 * 255.255.255.0 U 0 0 0 wlan2 192.168.1.1 * 255.255.255.255 UH 0 0 0 wlan2 Any assistance would be greatly appreciated. I have searched forums but can't find an answer that solves my problem.
  3. So last week I bought a DVD (from eBay), which was supposed to be or I had assumed to be a Mac OS X Yosemite installer. I wanted to use this DVD to install Mac OS X Yosemite into VirtualBox on my Windows 8.1 PC. Unfortunately, I was unable to do it, even after I tried to convert the DVD into an ISO, and also tried to convert the DVD into a USB "bootable" drive. Nothing worked. I even tried to install the DVD into VMWare, also with no success. If anyone has any suggestions or can offer help on this matter, it would be greatly appreciated. Thanks!
×
×
  • Create New...