Search the Community

Hi All, I'm a new user and i just recently got a Mark V pineapple. I've done minimal changes to the pineapple and setup the internet sharing as per the instructions stated here: https://wiki.wifipineapple.com/legacy/#!ics.md On 172.16.42.1:1471, however, i was not able to get an internet IP address via the pineapple "network" tile. It times out and says Error Connecting. The same goes for the tile for checking firmware upgrades. My internet facing wifi adapter has been set to "Allow other network users to connect through this computer's Internet connection" and has been shared with "Ethernet" connection (Windows 10) My pineapple facing ethernet adapter "Ethernet" TCP/IPv4 setting has been set up with IP address: 172.16.42.42/255.255.255.0, default gateway (empty), DNS: 8.8.8.8. I'm not sure what else i need to do to let my pineaple Mark V access the internet. Appreciate some help from kind souls here ?

Hi, I am new to wifi pineapple. I am having a problem with my wifi pineapple nano for windows 10. I followed the initial setup of nano for windows and I am not getting any internet connection. When I click the "Load Bulletins" from Dashboard, I get the error: "Error connecting to WiFiPineapple.com. Please check your connection.". I have attached the images for my network setting and the error I am getting. Can someone please tell me what I am doing wrong? Thanks!

First things first - I have already gone through a bunch of posts on this forum but none of them have been helpful to solve the specific problem that I am having so any help here is greatly appreciated. My setup is something like this: MK5 Kali Linux installed on Virtual Box sitting on Mac OSX 10.9.4 The network settings of the Kali Linux Virtualbox is set to "NAT". So, when I type in ifconfig inside Kali, I see just 2 interfaces: eth0 with an IP address of 10.0.2.15 lo with an IP address of 127.0.0.1 On my macbook, I have a bunch of interfaces. The important ones are listed below: en0 with an IP address of 172.16.42.210 - This is the ethernet interface connected to the MK5. en1 with an IP address of 192.168.1.3 - This is the wifi interface connected to my router Straight out of the box, I was able to successfully connect to MK5 via ethernet and fire it up. No problems there. I could reach to it from the macbook as well as Kali. After starting it up, I noticed there was no internet access on the MK5. So, I read some posts and figured that MK5 has 2 wlans now. So, I enabled Wlan1 from the portal, navigated to Client Mode. Scanned for my router's SSID and connected to it. I now had internet access on my MK5 so I upgraded the firmware, installed infusions, etc. I also had internet access on any other device connected to my MK5 via MK5's broadcasted SSID at Wlan0. So, everything till now looks good. I have my MK5 setup and running with internet access. I can connect any device to MK5 and have internet access to it. I can access Mk5's portal from both my Macbook and Kali. I can also run infusions like tcpdump, sslstrip, etc. on the Mk5 itself. So, on one hand I have my Macbook and Kali connected to the router and on the other hand, I have my MK5 connected to the router as well. And, I am able to access Mk5 from my Macbook/Kali via the ethernet port. However, the above setup is not something I want because all traffic sent to MK5 is automatically sent to the internet via the router because Wlan1 is enabled on Mk5. What I want is: Wlan1 be disabled so that only Wlan0 is open on the Mk5 broadcsting its SSID. All the traffic sent to the MK5 should be routed via Kali on my Macbook and then onwards to the router so that I can run tools on Kali and capture the traffic. I understand this means I will be sharing my internet from the wifi port of my macbook onto the ethernet port for the Mk5 to connect. But, I have read that the ICS on macbook should not be enabled because it changes the IP address? So, how do I get this working when the Wlan1 is disabled on the Mk5 and ICS is turned off on Macbook? Also, since i really want to be doing all this on the Kali VM rather than the Macbook, I downloaded the wp5.sh script from wifipineapple.com and ran it on the Kali VM. Pineapple Netmask: 255.255.255.0 Pineapple Network: 172.16.42.0/24 Interface between PC and Pineapple: eth0 ----> not sure what this should be since I'm on the Kali VM? Interface between PC and Internet: wlan0 ----> I only see eth0 and l0 listed on Kali so what value should I enter here? en1 of macbook? Internet Gateway: 10.0.2.2 IP Address of Host PC: 172.16.42.210 IP Address of Pineapple: 172.16.42.1 I am not sure the above values are correct or if the scenario I describe here is even possible? Can somebody please assist? Thanks

When I first set up the pineapple I was able to use the Ethernet cable to connect into my computer (both Windows and Linux) and from there access the Pineapple Bar Infusions/Internet. Out of the blue I was no longer able to get infusion connections or internet connections through the pineapple. As a test I used wlan1 to connect to my wifi directly and of course I get an internet connection and infusion updates. So in short what may cause this disconnect using the Ethernet? (Yes, I used the Windows ICS as described in the manual correctly because it worked out of the box for a few days before it stopped working. I used the wp5.sh for the Linux machine with no luck after the initial install.) I also tried to reset to factory defaults...not luck. Thanks UPDATE: I upgraded the 1.0.3 firmware and still no luck getting Ethernet ICS to work on Windows or Linux. Still searching for an idea...