Jump to content

Search the Community

Showing results for tags 'factory'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • Talk
    • Everything Else
    • Gaming
    • Questions
    • Business and Enterprise IT
    • Security
    • Hacks & Mods
    • Applications & Coding
    • Trading Post
  • Hak5 Gear
    • Hak5 Cloud C²
    • WiFi Pineapple Mark VII
    • USB Rubber Ducky
    • Bash Bunny
    • Key Croc
    • Packet Squirrel
    • Shark Jack
    • Signal Owl
    • LAN Turtle
    • Screen Crab
    • Plunder Bug
  • O.MG (Mischief Gadgets)
    • O.MG Cable
    • O.MG DemonSeed EDU
  • WiFi Pineapple (previous generations)
    • WiFi Pineapple TETRA
    • WiFi Pineapple NANO
    • WiFi Pineapple Mark V
    • WiFi Pineapple Mark IV
    • Pineapple Modules
    • WiFi Pineapples Mark I, II, III
  • Hak5 Shows
  • Community
    • Forums and Wiki
    • #Hak5
  • Projects
    • SDR - Software Defined Radio
    • Community Projects
    • Interceptor
    • USB Hacks
    • USB Multipass
    • Pandora Timeshifting

Find results in...

Find results that contain...


Date Created

  • Start

    End


Last Updated

  • Start

    End


Filter by number of...

Joined

  • Start

    End


Group


AIM


MSN


Website URL


ICQ


Yahoo


Jabber


Skype


Location


Interests


Enter a five letter word.

Found 7 results

  1. I am following these steps from the wiki: Factory Reset / "Unbricking" In the extreme case that a LAN Turtle has become permenantly inaccessible or inoperative, there is a quick method for recovery using a special web interface. Download the latest factory image from https://downloads.lanturtle.com/turtle-2-factory.bin Carefully open the LAN Turtle case by removing the two screws underneath the sticker on the bottom While holding the button on the bottom of the LAN Turtle, plug the device into a computer After 3 seconds let go of the button and wait an additional 30 seconds to receive an IP address from the LAN Turtle If you do not receive an IP address in the 192.168.x range from the LAN Turtle within a minute, statically assign the LAN Turtle's interface to 192.168.1.2 (netmask 255.255.255.0) Browse to the LAN Turtle firmware recovery web interface at http://192.168.1.1 Follow the on screen prompts to upload and flash the factory image downloaded in step 1 When the flash is complete the LAN Turtle will reboot and will be accessible again from 172.16.84.1 with the default username root and password sh3llz I do not get an IP in the 192.168.x.x range any time I hold down the button. When I hold down the button on my Kali linux box it comes up as 172.16.84.245 with a gateway of 172.16.84.1. If I manually set the adapter IP in Kali to 192.168.1.2 I am not able to get to a website using my web browser. I have tried this on a Linux Mint laptop, Kali linux laptop and Mac computer with all the same results. I have tried holding the button for 1 second and for 30 seconds and places in between with the same results. Do you think my LAN Turtle is defective?
  2. Just bought a Tetra a few weeks ago. Every time I shutdown or reboot the Pineapple, it factory resets. Nothing saves, and I have to go through full setup everytime. What can I do to stop this or exchange it?
  3. Hi, it is my first LAN Turtle, I ordered it as Bundle from the US Store. I did the Update to V2 with Putty & Network cable throug the LanTurtle I am not able to install anything from the Directory. I tryed factory Default reset with the .bin of your Website. Stil the same Problem. In the List of the Modules there is no X by Modulemange. When I select it, it tells me Current Status:Stopped And Bootup Status: Enabled When I go to configure I can select Modules from Directory but nothing is installed in the end. I tryed everthing! Is there a solution?
  4. Hi, I am wondering if there is a manual method to perform a factory reset or re-installation of the firmware ? Thinking that it is good to ask/know before I start experimenting :) Thanks for the all the help upfront!
  5. I have followed the wiki steps for factory resetting the Lan Turtle ( https://lanturtle.com/wiki/#!index.md ) In addition to this, I have followed this fellow who seems to have had the same problem. (And fixed it) However, I am having absolutely no luck reaching the internal webserver of the lan turtle. Once I type in 192.168.1.1 into my web browser, it hangs for approximately 2 seconds, and states that there is no internet. If someone could help me asap, it would be greatly appreciated, as I need it for a demonstration this week. (Tomorrow evening) Thank you for your time. PS. If it helps, I am on the Parrot operating system, although I do have both windows and default debian installed as well. (I've tried all 3 OSs, and still no luck.)
  6. Just received a brand new MKV a couple of days ago. I plugged it in with the original SD card and got blue light blinking more than 30’. I changed the original SD for a SD card samsung class 10, 16 GB formatted FAT32 (with no files as the original one), I got same result. Wrote in the SD card last upgrade.bin and md5 downloaded from MKV site and exactly same result. I downloaded and flashed factory.bin using the “recovery web interface” as suggested in “flashing Instructions”. The transfer was successfully but once I unplugged it and re plugged it the result was exactly the same the blue light is blinking forever. I also tried to change the power supply using one DC 10V 3A but same issue. Any one would have some suggestion to help me to revive the MKV ? Is there something that I am doing wrong or that I missed ? Is there a site where one could download an old version of factory.bin ? thx
  7. [sOLVED!] For those of you having the same problem as me, I fixed it by using the power cable that it was shipped with, rather than the USB power cable. Because I am in the UK, I had to use a shaver to mains adapter. Thanks everyone. Hey guys, me and a friend got our hands on the AP121U via ebay and were hoping to flash them with the Jasager firmware. We followed the guide to the letter and used UART cables to flash the factory binaries onto the devices. However, they enter into a boot loop after resetting them. I can hit 'f' and return to drop into failsafe mode, where we're presented with the following prompt: root@(none):/# I've tried starting dropbear to scp over the Jasager files to /tmp/, but I can't even establish a connection (yeah, I'm using the PoE port). Any ideas would be much appreciated. P.S. I thought it could have been a dodgy AP121U, but my friend's does EXACTLY the same thing as mine.
×
×
  • Create New...