Search the Community
Showing results for tags 'connectivity'.
Found 3 results
Hi everyone I have some Problems with my new LAN turtle. When i insert my SIM Card and boot up the turtle via USB on my Computer, everything works well, i can connect to the turtle via SSH an can see that the 3G interface got an IP and can connect to the Internet. --> See screenshot below (3g_visible.png) But as soon as i insert a LAN cable in the ethernet port of the turtle, the 3G Interface goes down and never comes up again, see second screenshot. I first thought this was due to the "WAN-FAllback" option, but i disabled the function and the problem is still there 😕 Any ideas what i could try to fix this issue? End goal: The Ethernet Port should allow me to connect to the internal network (get an IP via dhcp) , while the 3G connection should stay the primary internet connection and create the SSH connection to our Server. The USB will get connected to a powerbank. Best, Mo
TL;DR WifiPineapple Nano works 100% if I use my Ethernet cable, but will not connect to the internet using the Wifi adapter on my Laptop. Herewith the steps I have taken: ON WIFI Using HP 9740 Laptop, LAN cable disconnected, eth0 down, on-board Wifi connected to my home AP WifiPineapple Nano disconnected Boot Kali Linux 2016.2 Run wp6.sh, select [G] Default gateway identified as 192.168.1.1, select [Y] Internet interface reported as wlan0, select [Y] Detected WifiPineapple on interface eth1, select [Y} Once the light is solid blue, select [C] Detecting WifiPineapple......found. Browse to http://172.16.42.1:1471 Log into the WifiPineapple successfully Can browse to google.com, and the rest of the internet Load bulletins and Get Modules doesn't work (as per many other reports in this forum) Results of route -n: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 172.16.42.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 600 0 0 wlan0 ON LAN LAN cable plugged in, wlan0 down, (same network as Wifi) Exactly the same steps as above, except I am offered eth0 as the default gateway EVERYTHING WORKS 100%, including loading bulletins and Get Modules Results of route -n: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 172.16.42.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 100 0 0 eth0 I have attached a full comparison of ifconfig and route -n step by step throughout the process in the hope that someone can shed some light on why it works perfectly with a LAN cable plugged in, but on Wifi I can not get to the Internet from the Nano. All suggestions greatly appreciated. Thanks Void Main() WifiPineappleConfig-LAN.txt WifiPineappleConfig-Wifi-Eth0Down.txt
Hi All, I'm an absolute beginner at this, so please be gentle! I've just received my nano, and I'm having a few problems in connecting over USB. Windows didn't have the drivers at first, but recognised it as an asix AX88772A usb to fast ethernet adapter. Downloaded the driver from Asix, and we are good. I managed to log into the AP to update the firmware, but only by logging into the wifi AP. The pineapple appears in my network connections, and I've shared my home wifi with it, and set the pineapple IP to 172.16.42.1, 255.255.0.0. Status on the pinapple in network connections still says no internet connectivity on IPV4 and I can't ping the IP address either. My laptop IP is in the 192 range, do I need to put it in the 172 range with my router? or does the ICS take care of this? Thanks for any help!!!